Replacing the light bulb in the refrigerator Burning: instructions for 2010–2026 models

Burnt light bulb in a refrigerator Gorenje (in the Russian version - Combustion) is a problem that every owner faces sooner or later. Even if the equipment works properly, the lack of lighting creates discomfort: you have to use a flashlight or open the door wider to see the contents. Fortunately, you can replace the lamp yourself without resorting to the help of a technician. In this article we will figure out how to do it correctly, what tools you will need and what to look for when choosing a new light bulb.

The manufacturer Gorenje uses several types of lighting elements in their refrigerators - from classic incandescent lamps to LED modules. The mounting design also varies depending on the model and year of manufacture. For example, in old refrigerators of the series RK (until 2015) cartridges are often found E14, while in new NRK and NK (2018–2026) LEDs with a connector are installed G4 or GU5.3. We will go into detail about each option so that you can determine exactly which type of lamp is right for your model.

It is important to consider that replacing a light bulb is not only a matter of convenience, but also of safety. An incorrectly selected lighting element can overheat, melt plastic parts, or even cause a short circuit. Therefore, before starting work, be sure to unplug the refrigerator read our recommendations.

How to determine the type of light bulb in your refrigerator Burning

The first step is to identify which lamp is installed in your model. To do this, it is not necessary to disassemble the refrigerator: just look at the technical data sheet or inspect the burnt out light bulb (if it is still there). Here are the main options that are found in refrigerators Gorenje:

• 💡 Incandescent lamps —the classic version with a base E14 or E27. Most often installed in models before 2016 (for example Gorenje RK4181, RK6191). The power usually does not exceed 15–25 W.
• 🔆 Halogen lamps are brighter and more durable, with a base G4 or GU5.3. Found in refrigerators of the middle and premium segment (series NRK, NKI).
• 💫 LED lamps - modern models (2018 and newer) are often equipped with LED modules with a connector G4 or built into the lampshade. They are economical and last up to 50 000 hours.
• 🔌 Built-in LED panels —in some models (for example, Gorenje ORB153) the lamp is integrated into the lampshade and cannot be replaced. In this case, you will have to change the entire lighting unit.

If you are unsure of the type of lamp, pay attention to its shape and markings. For example, light bulbs E14 have a threaded base with a diameter of 14 mm, and G4 - two pins at a distance of 4 mm from each other. You can also use a flashlight to examine the socket: in LED models, the driver (a small board with resistors) is often visible.

If your refrigerator was manufactured after 2020, there is a high probability that it has an LED module installed. In this case, replacement may require a soldering iron or a special connector. For accurate identification, check the markings on the back wall of the refrigerator or in the documents - the year of manufacture and serial number are indicated there.

⚠️ Attention: In refrigerators Gorenje with a system NoFrost (for example, NRK6191), the lamp may be hidden under the decorative panel. Do not try to remove it by force - first read the instructions or the section below on disassembling the lampshade.

Preparation for replacement: tools and safety measures

Before starting the replacement, make sure that you have everything you need. Here is the minimum set of tools and materials:

• 🔧 Phillips screwdriver (usually PH2 size is enough) - for dismantling the ceiling.
• 🔌 New light bulb - suitable type and power (more on this below).
• 🧤 Gloves —to avoid leaving fingerprints on the bulb (especially important for halogen lamps).
• 📸 Smartphone —for photographing the process (useful if you have to put it back together).
• 🔦 Flashlight —to better see the fastenings.

Also prepare your work area: remove food from the refrigerator (or put it in the freezer), unplug the equipment and let it stand for 10-15 minutes if it has just been working. This is necessary in order to avoid burns from heated parts.

Unplug the refrigerator from the outlet|Empty the shelves next to the lampshade|Prepare a new light bulb (check the base)|Wear gloves (for halogen/LED lamps)|Take a photo of the original position of the parts-->

Pay special attention to choosing a replacement. refrigerators Gorenje recommended lamps with the following characteristics:

Do not use lamps more powerful than indicated in the instructions! This can lead to overheating of the lampshade and melting of the plastic. For example, if in the passport. indicated maximum 15 W for E14 base, do not install a 25 W lamp - even if it is physically suitable.

Step-by-step instructions: how to remove the lampshade and replace the light bulb

The replacement process depends on design of the lampshade. In most refrigerators Gorenje it is mounted on latches or screws. Let's consider both options.

Option 1: Lampshade on latches (without screws)

This type of fastening is found in models RK i some NRK. To remove the lampshade:

1. Open the refrigerator door and find the lampshade (usually it is located in the upper part, closer to the back wall).
2. Gently press the lampshade on the side - it should move slightly away from the ceiling. Often there are special grooves for. screwdrivers.
3. Pull the lamp towards you and down to release it from the latches. Move smoothly so as not to break the fasteners.
4. Unscrew the burnt out light bulb (counterclockwise for E14 or pull towards you for G4).
5. Install the new lamp, making sure that it is firmly seated in the socket.
6. Return the lampshade into place, snapping it until it clicks.

Option 2: Ceiling lamp with screws

In refrigerators Gorenje with a system NoFrost (for example, NRK6191) the lampshade is often secured with screws. Here the procedure is as follows:

1. Unplug the refrigerator and remove the top shelf (if it is in the way of access).
2. Locate 2-4 screws securing the shade. They may be hidden under decorative plugs.
3. Carefully unscrew the screws with a Phillips screwdriver and place them in a safe place.
4. Lower the lamp down - it usually hangs on the wires. Do not pull too hard so as not to damage the contacts!
5. Replace the light bulb following the instructions for its type (see table above).
6. Install the lampshade back and tighten the screws. Make sure that it sits level, without distortion.

In some models (for example, Gorenje ORB153), the lampshade may be part of the overall control panel. In this case, you will have to remove the entire panel, first disconnecting the cables. If you are not confident in your abilities, it is better to contact a specialist.

⚠️ Attention: In refrigerators with electronic control (display on the door), when replacing the lamp, the temperature setting may be reset. After turning on, check the parameters in the menu Settings → Temperature.

Features of replacing LED lamps in new models

If your refrigerator Gorenje was produced after 2018, most likely it has LEDs installed. Replacing them has its own nuances:

• 🔌 LED modules G4 they are replaced in the same way as halogen ones - just remove the old lamp and insert a new one. However, pay attention to the polarity: there may be “+” and “–” marks on the base.
• 🔧 Built-in LED panels (for example, in ORB173) require a complete replacement of the lampshade. To do this, you need to disconnect the power connector and install a new module.
• 💡 Lamps with a driver (found in premium models) may have a separate power supply. If after replacing the LED the lamp does not light, check the voltage at the contacts with a multimeter.

For LED lamps, it is critical to maintain polarity. If the light does not light up after installation, try turning the lamp over. Also make sure that the new lamp has the same voltage as the old one (usually 12 or 24 V).

What to do if the new LED lamp is blinking?

The blinking of the LED can be caused by several reasons:

1. Poor quality driver - if a cheap power supply is installed in the lampshade, it may not cope with load. Solution: replace the entire module.

2. Wrong polarity —check if the “+” and “–” are connected correctly.

3. Poor contact —inspect the connector for oxidation or contamination. If necessary, clean the contacts with alcohol.

4. Incompatibility with a dimmer — some refrigerators Gorenje have a soft-on function. If the lamp is not dimmable, it will flicker. In this case, you need a special dimmable LED.

If you are replacing the LED module completely, pay attention to its markings. For example, in refrigerators Gorenje NK6191 modules with article number 610123860 (for models 2020–2022) are installed. Check this number in the instructions or on the manufacturer's website to buy exactly the same one.

Common mistakes and how to avoid them

Even such a simple procedure as replacing a light bulb may not go according to plan. Here are the most common mistakes and ways to prevent them:

• 🔌 Using a lamp of inappropriate power — leads to overheating. Always check the maximum permissible values ​​in the passport.
• 🧤 Touching the bulb of a halogen lamp with bare hands —grease marks cause local overheating and shorten the service life. Use gloves or a napkin.
• 🔧 Tightening the lamp in the socket too tightly can damage the base. Screw in all the way, but without force.
• 💡 Ignoring the polarity of LED lamps - if the LED does not light, turn it over.
• ⚡ Replacing the lamp with the power on - this is not only dangerous, but can also cause short circuit. Always remove the plug from the socket!

Another typical problem is that the lampshade does not sit back in place. Most often this happens because the wires are twisted or the lamp is not fully installed. Check that:

• All lamp latches coincide with the grooves on the body.
• The wires are not pinched and do not interfere with installation.
• The lamp is completely inserted into the socket (for G4 it should be audible click).

If after replacement the lamp does not light, check:

1. The serviceability of the new lamp (try it in another device).
2. The integrity of the socket - sometimes the contacts oxidize or bend.
3. The voltage in the socket (possibly the problem is not in the refrigerator).

⚠️ Attention: In refrigerators Gorenje with an inverter compressor (series NKI), when replacing the lamp, the protection may trip. If after turning on the refrigerator does not start, turn it off for 5 minutes, then try again.

Where to buy a light bulb for a refrigerator Burning and how much does it cost

A new lamp can be purchased in several ways:

• 🛒 Official service centers Gorenje is the most a reliable option, but prices are higher than market prices. A lamp E14 will cost 300-500 rubles, an LED module - 800-1500 rubles.
• 🌍 Online stores (Wildberries, Ozone, AliExpress) - a large selection, but there is a risk of running into a fake. Pay attention to the reviews and rating of the seller.
• 🏠 Electrical goods stores (Leroy Merlin, Castorama) - suitable if you need a standard lamp E14 or G4.
• 🔧 Home appliance repair shops - often sell spare parts with a guarantee.

When purchasing, check the following parameters:

• Type of base (E14, G4 etc.).
• Maximum power (for example, "no more than 15 W").
• Voltage (usually 220 V for incandescent lamps or 12/24 V for LED).
• For LEDs - color temperature (2700–4000 K for warm light).

Cost of lamps for refrigerators Gorenje in 2026:

Lamp type	Price, rub.	Where is the best place to buy
Lamp incandescent E14, 15 W	150–300	Any electrical goods store
Halogen G4, 20 W	200–400	Ozone, Wildberries
LED G4, 3 W	300–800	AliExpress (with waiting) or service center
LED module for ORB153	1000–2500	Official dealer Gorenje

If you are not sure about the choice, take the burnt lamp with you to the store - the seller will help you choose an analogue. For rare models (for example, refrigerators 2010–2015), you may need to order online.

When is it better to call a technician: complex cases

In most cases, you can replace the light bulb in the refrigerator Gorenje you can do it yourself. However, there are situations when it is better to contact a professional:

• 🔌 The lamp is integrated into the control board (found in models with a touch screen, for example, Gorenje ORB173). This requires a soldering iron and knowledge of electronics.
• ⚡ Problems with the wiring —if during replacement you notice melted wires or a burning smell, do not take risks. This is a sign of a short circuit.
• 🛠️ The lampshade is stuck or the fasteners are broken - attempts to remove it by force can lead to cracks in the case.
• 💡 Not only the lamp does not light, but also the display - this may indicate a faulty power supply.

The cost of replacing a light bulb by a technician in 2026 ranges from 800 to 2000 rubles (depending on the region and complexity of the work). If the entire lampshade or LED module needs to be replaced, the price can rise to 3,000–5,000 rubles. However, in most cases, self-repair is 3-5 times cheaper.

If you decide to call a technician, prepare the following information:

• Refrigerator model (located on the sticker inside or on the back).
• Year of manufacture (indicated in the passport).
• Lamp type (if known).
• Description of the problem (the lamp does not light, blinks, the lamp does not lock, etc.).

⚠️ Attention: If your refrigerator Gorenje is under warranty, do not try to replace the light bulb yourself! This may result in denial of warranty service. Contact an authorized service center.

FAQ: Frequently asked questions about replacing a light bulb in a refrigerator Burning

Can an LED lamp be used instead of an incandescent lamp?

Yes, but you need to take into account several nuances:

• The base must match (for example, E14 on E14).
• The maximum power of the LED lamp should not exceed the power of the original incandescent lamp (for example, if it was 15 W, take a 3-5 W LED).
• For some models Gorenje required lamps with a certain color temperature (usually 2700–3000 K for warm light).

Advantages of LED: lower energy consumption, long service life, no heating. However, in refrigerators with old cartridges (E14), it may be necessary to replace the cartridge with one compatible with LED.

Why does a new light bulb burn out quickly?

If the lamp burns out within a few days or weeks, the reasons may be as follows:

• 🔌 Voltage surges —check the stability of the network using a multimeter. If necessary, install a stabilizer.
• 💡 Poor contact in the socket —oxidized or bent contacts cause overheating. Clean them with sandpaper.
• ⚡ Power mismatch —if the lamp is too powerful, the socket overheats. Install a lamp with a lower power.
• 🔄 Frequent opening of the door —in refrigerators with a light sensor, the lamp turns on every time it is opened, which shortens its service life.

For halogen and LED lamps it is also important to avoid touching the bulb with bare hands - traces of fat lead to local overheating.

How to remove the lampshade if it is not held on by latches and the screws are not visible?

In some models Gorenje (for example, RB6021) the lampshade is mounted on hidden latches. Try the following:

1. Gently pull the lampshade towards you, slightly swaying it left and right. Often the latches are located on the sides.
2. Use a plastic spatula or credit card to pry the lampshade from the side. Do not use metal tools - they will scratch the plastic.
3. Shine a flashlight into the cracks - sometimes the latches are visible in side lighting.
4. If the lampshade still cannot be removed, check to see if there is a decorative cover underneath (it can be attached with Velcro).

As a last resort, refer to the instructions for your model or watch disassembly on YouTube (for example, by request "Gorenje [your model] disassembly").

Is it possible to replace a light bulb in a Burning refrigerator with NoFrost?

Yes, the replacement process in refrigerators s NoFrost (for example, Gorenje NRK6191) does not differ from conventional models, but there are several features:

• The lampshade is often hidden behind a decorative panel that needs to be removed.
• In some models the lamp is located not in the upper part, but on the side (for example, c Gorenje NKI6191).
• After replacement, check that the NoFrost fan is working normally - sometimes when disassembling the ceiling you can hit its blades.

If your refrigerator is equipped with built-in LED module, replacing it may require turning off the power to the entire control panel. In this case, it is better to contact a technician. data-i="301">built-in LED module

What to do if the refrigerator does not turn on after replacing the light bulb?

If the refrigerator stops working after replacing the lamp, follow these steps:

1. Check whether the lampshade is tightly seated - sometimes incorrect installation closes the contacts.
2. Take out the new lamp and try to turn on the refrigerator without it. If it works, the problem is in the lamp (possibly a short circuit).
3. Inspect the cartridge for melting or blackening. If the contacts are damaged, the cartridge needs to be replaced.
4. Check the fuse (if your model has one) - it could have burned out during the jump. voltage.
5. If nothing helps, turn off the refrigerator for 10-15 minutes, then turn it on again. The overload protection may have tripped.

If the refrigerator still does not turn on, the problem is probably not in the lamp, but in the electrical circuit. In this case, a technician needs to diagnose it.