We rehang the LG refrigerator doors ourselves: instructions with photos and tips

Rehanging refrigerator doors LG is a task that many owners face when moving, renovating, or simply wanting to optimize kitchen space. Despite the apparent complexity, the procedure is quite doable with your own hands if you know the key nuances: from the type of hinges to the location of the fasteners. In this article we will analyze a step-by-step algorithm for different models LG (including No Frost and Total No Frost), indicate the necessary tools and warn against typical mistakes that can lead to leakage or damage to the door.

It is important to consider that the design of the hinges and the method of fastening may vary depending on refrigerator series and year of manufacture. For example, in models LG Door-in-Door the process is more complicated due to the additional internal door, while in classic two-chamber refrigerators (for example LG GA-B489a standard set of actions is sufficient. We have collected universal recommendations and highlighted points where special care is required - from removing decorative plugs to adjusting the position of the door after installation.

If you have never done such work, do not worry: the manufacturer has provided the possibility of self-installation, and all the necessary holes for alternative fastening are already in the case. The main thing is to take your time and follow the logic of the process. Let's start with preparation!

Preparation: tools and working conditions

Before you start dismantling the doors, make sure that you have everything you need. Missing even one tool can delay the process or damage plastic parts. Here is the complete list:

• 🔧 Phillips screwdriver (size PH2 is usually suitable) - for most hinge screws.
• 🔧 Flat screwdriver - for removing decorative plugs and prying up the fasteners.
• 📏 Ruler or tape measure —to measure the gaps after installation.
• 🧲 Magnet or tape —for temporarily fixing the removed screws (do not lose them!).
• 🧴 Silicone grease (optional)—for processing hinges after overhang.
• 🧤 Gloves —to avoid scratching the glossy surface of the door.

Also prepare the work space:

• 🚪 Free access to the refrigerator on all sides - at least 1 meter of free space.
• 🧊 Unplug the refrigerator and defrost (if the model is not No Frost).
• 📦 Remove all products and shelves from the door - they may fall when removed.
• 🪑 Place a soft cloth or cardboard on the floor to avoid scratching the door when installing.

⚠️ Attention: If your refrigerator LG is equipped with a system Smart ThinQ or a display on the door, before starting work, check whether the electronics are blocking access to the fasteners. In some models. (for example, LG InstaView) you need to first turn off the power and wait until the display turns off completely.

Determining the type of hinges and mounting pattern

The design of hinges for refrigerators LG varies depending on the model. To avoid mistakes, first identify your type:

To accurately determine the mounting pattern:

1. Open the refrigerator door and inspect the hinges at the top and bottom.
2. If plastic plugs are visible, they need to be removed (pry them off with a flat screwdriver).
3. Under the plugs you will see the screws: their number and location will tell you how to reposition them.

In most models LG are used symmetrical hinges, that is, mounting holes are already provided on both sides. However, in refrigerators Side-by-Side may be required rearranging the top bar with the display - this moment is often missed, which is why the later door does not close tightly.

Step-by-step instructions: remove and rehang the doors

Now we move on to the process itself. We will analyze the universal algorithm for classic two-chamber refrigerators LGIf you have a different model, adapt the steps to its design.

Step 1: Removing the top door

Start with the top door (freezer or refrigerator - depending on the model):

1. Open the door 90 degrees and fix it (you can place a book or ask assistant).
2. Remove the decorative plugs from the hinges (pry them off with a flat screwdriver).
3. Unscrew the screws securing the top hinge to the refrigerator body (usually 2-3 screws).
4. Carefully lift the door up to remove it from the lower hinge. Do not pull towards yourself! —it is removed vertically.

Step 2: Removing the lower door

If you have two-chamber refrigerator:

1. Remove the middle hinge (between the doors) by unscrewing the screws.
2. Open the bottom door and unscrew the screws of the bottom hinge.
3. Remove the door by pulling it up (same as the top one).

⚠️ Attention: In models with the system Total No Frost (for example, LG GC-B247there may be wire sensorbetween the doors. Do not pull it by force - first disconnect the connector (usually it is located under the top hinge).

Step 3: Rearranging the hinges

Now move the hinges to the opposite side:

1. Remove the screws from the old holes and insert them into the symmetrical holes on the other side.
2. If there are no holes - use template (usually included with the refrigerator). If it is not available, measure the distance from the edge to the hinges on the old side and transfer the markings.
3. Secure the hinges, but do not tighten the screws completely - first you need to adjust the position of the door.

Step 4: Installing the doors

Assemble in the reverse order:

1. Place the bottom door on the bottom hinge, then the top one.
2. Make sure the doors are fit evenly to the body. If there is a distortion, loosen the screws and. adjust.
3. Close the refrigerator and check for any gaps. Use sheet of paper: if it pulls out easily when the door is closed, additional adjustment is needed.

Hinges secured symmetrically|Doors open/close smoothly|The seal is not twisted|The screws are tightened, but not overtightened|Tightness checked (test with paper)-->

Adjusting the doors after rehanging

Even if at first glance everything looks perfect, be sure to adjust the door incorrectly. to:

• 🔋 Increased energy consumption (due to leakage).
• 🧊 Freezing of the seal.
• 🚪 Spontaneous opening.

For adjustment:

1. Loosen the screws on the hinges (do not unscrew completely!).
2. Adjust the position of the door:
   • If the door is sags - lift it up and tighten the top hinge.
   • If does not fit underneath - adjust the bottom loop.
   • If skewed diagonally - loosen both loops and align visually.

Tighten the screws and re-check the tightness.

In models LG with an electronic display (for example, LG InstaView Door-in-Door) after rehanging it may required reset settings. To do this:

Press and hold the "Door Alarm" + "Freezer" buttons for 5 seconds.

What to do if the door does not close tightly?

If after adjustment there is a gap left, check:

1. Seal —it may be dirty or deformed. Clean it with soapy water and lubricate it with silicone grease.

2. Floor levelness —the refrigerator must be strictly level. Use adjustable feet.

3. Hinges - sometimes the screws are not tightened enough or, conversely, overtightened. The optimal force is when the door holds on its own, but does not require effort to open.

Common mistakes and how to avoid them

Even experienced craftsmen sometimes make mistakes when hanging doors. Here are the most common:

• 🔧 Use of unsuitable tools —for example, a screwdriver that is too large, which will tear off the screw slots. Always take PH2 or PZ2.
• 🚪 Removing the door "pull" - this leads to deformation of the hinges. The door can only be removed vertically up!
• 🔌 Forget to disconnect the wires (in models with a display or sensors). This can damage the contacts.
• 📏 Incorrect hole markings —if you drill new holes “by eye,” the door will be askew.
• 🧴 Ignore lubrication of hinges —without it, a creaking will appear over time.

You need to be especially careful with models LG Door-in-Door. Here they often forget about inner door, which also requires reweighing. If it is left on the same side, the outer door will not close tightly.

⚠️ Attention: In refrigerators LG with a system Linear Cooling (for example, LG GC-X247) after rehanging it may go astray calibration of temperature sensors. If the refrigerator has become worse in cooling, perform automatic recalibration through the settings menu (section Diagnostic Mode).

Features for Side-by-Side and Door-in-Door models

Refrigerators LG Side-by-Side and Door-in-Door require a more complex approach due to the dimensions and additional mechanisms. Here are the key points:

Side-by-Side

• 🔧 The hinges are more massive, so you definitely need an assistant the door weighs 15–20 kg.
• 📏 The top bar with the display is attached separately. you need to remove to door dismantling.
• 🔌 In some models (for example, LG GS-X961there is door lock - it also needs to be moved.

Door-in-Door

• 🚪 The inner door is removed separately. First, dismantle the outer one, then the inner one.
• 🔧 The hinges of the inner door are attached to small screws —use a screwdriver PH1.
• ⚠️ When assembling, make sure that magnetic latches the inner door matches the mating parts on the outer one.

These models may also require reconfiguring electronic modulesFor example, c LG InstaView after re-hanging, you need to reset the display settings:

Press "Ice+" and "Lighting" for 10 seconds until the indicator blinks.

When is the best time to contact specialist

Although re-hanging doors LG usually does not require professional skills, there are situations when it is better to call a specialist:

• 🔧 If the hinges deformed or the screws “slipped” during previous attempts.
• 📱 In models with Wi-Fi module (for example, LG ThinQ) after rehanging, flashing may be required.
• 🚪 If the door after installation does not stay closed (problem with the magnetic seal).
• ⚡ If damage is suspected electrical wiring (for example, if after assembly it does not work display).

The cost of professional re-hanging in service centers LG ranges from 1,500 to 3,000 rubles (depending on the model) If you are not confident in your abilities, sometimes it is cheaper and safer to entrust the work to a specialist than to risk an expensive one. repair.

⚠️ Attention: If your refrigerator is under warranty, re-hanging the doors yourself may lead to cancellation of warranty obligations. Before starting work, check this point with the service center.

FAQ: Answers to frequently asked questions

Is it possible to hang the doors on an LG refrigerator without an assistant?

Theoretically, yes, but it is difficult. Doors (especially in models Side-by-Side) weigh 10-20 kg, and hold them with one hand while twisting them. screws, inconvenient. For two-chamber refrigerators, you can do without an assistant if you secure the door with a rope or a belt. In models Door-in-Door an assistant is required - due to the internal door and wiring.

What to do if, after rehanging, the refrigerator begins to work loudly?

This may be due to with:

• 🔧 Loose door fit — the compressor works harder, trying to maintain the temperature.
• 🧊 Displacement of the temperature sensor (in models with No Frost).
• 🔌 Damage to the seal —check it for gaps.

Solution: adjust the hinges, check the tightness and, if necessary, replace the seal.

Do you need to defrost the refrigerator before rehanging the doors?

If you have a model with No Frost or Total No Frost, defrosting is not necessary. In refrigerators with a drip system (for example, LG GA-B389it is recommended turn off the power and let ice to meltto avoid water getting on the electrical contacts during dismantling.

How often can you rehang the doors?

The design of the hinges is designed for LG designed for multiple rehanging, but each time the holes for the screws become a little loose. Optimal - no more than once every 2-3 years If you plan frequently. to change the opening side, use metal bushings to strengthen the holes.

Is it possible to rehang only one door (for example, only the freezer)?

Technically yes, but this not recommendedThe refrigerator doors LG are balanced by weight, and if you move only one, you may experience:

• 🔧 Warping of the body.
• 🚪 Uneven fit of the seal.
• 🔋 Increased load on the hinges.

If you need to move only the freezer (for example, in the model LG GB-B459), after installation, be sure to adjust the position of the refrigeration door to eliminate imbalance.