How to properly remove drawers in a Liebherr refrigerator: instructions with photos and tips

Refrigerators Liebherr famous for their reliability and thoughtful design, but even in such devices it is sometimes necessary to remove the internal drawers - for general cleaning, replacement or repair. It would seem, what could be simpler? However, careless actions often lead to broken fasteners, scratches on the plastic, or even damage to the guides. This is especially true for models with a system BioFresh or retractable containers VarioBoxwhere the fixation mechanism may differ from the standard one.

In this article we will look at how to properly dismantle drawers in refrigerators Liebherr of different series - from budget ones Comfort up to premium Premium NoFrost. You will learn what tools you may need (spoiler: you usually have enough hands!), how to avoid common mistakes, and what to do if the drawer gets stuck. And also - nuances for models with electronic controlwhere incorrect removal can disrupt the sensor settings.

Preparation: what needs to be done before removing the drawers

Before starting dismantling, make sure that the refrigerator Liebherr disconnected from the network. This is not only a safety issue, but also to prevent accidental activation of the compressor during work. This is especially important for models with NoFrost systemwhere the fan can start at any moment.

Also prepare:

• 🧼 A soft cloth or towel - to place under the drawers when removing them and to avoid scratches on the glass shelves.
• 📸 Phone with a camera - take a photo of the location of the drawers and fasteners if you are afraid of mixing them up when reassembling.
• 🔧 A plastic spatula or flat screwdriver (not metal!) - may be needed for models with hidden latches.
• 🧴 Plastic cleaner - if you remove drawers for washing, immediately prepare a solution (for example, vinegar + water 1:1).

If your refrigerator Liebherr is equipped with a system SmartDevice (control via application), check whether the electronic system is blocking the removal of drawers. In some models, when the door is open for more than 5 minutes, an alarm may sound - this is normal, but it is better to turn off notifications in the menu in advance.

Types of drawers in Liebherr refrigerators and their fastenings

The design of drawers in refrigerators Liebherr depends on the series and year of manufacture. Here are the main types that you can find:

Drawers deserve special attention BioFresh. They are equipped with special seals to maintain moisture, and improper removal can damage the seal. In models Liebherr CNef 4815 and similar ones, the drawers are fixed not only with grooves, but also with magnetic tape around the perimeter - it cannot be pulled by force!

Step-by-step instructions: how to remove a standard plastic box

This method is suitable for most models Liebherr budget and mid-range segment (for example, CUag 3311, CBPesf 4043). Follow the algorithm:

1. Pull out the drawer all the way —it should stop at the stops.
2. Lift the front part 1-2 cm. In most models, there are small protrusions on the front that cling to the guides.
3. Pull the box towards you, while simultaneously holding it in a raised state. It should come out of the grooves.
4. Remove it carefully the box completely, holding it from below so as not to drop it.

If the box does not give in, do not use force! Your model may have hidden fasteners. Pay attention to the side walls - sometimes there are small buttons or levers there (for example, in the series Premium).

Unplug the refrigerator from the outlet|

Empty the drawer of food|

Put a soft cloth on the floor|

Prepare a container for small items parts (if there is a risk of losing the fasteners)|-->

Features of removing VarioBox and BioFresh drawers

Drawers VarioBox (found in models Liebherr CBNes 5155, CBPesf 4815) have an adjustable height and retractable guides To remove them:

1. Pull the drawer out to its maximum length.
2. Press on red or black buttons on the sides of the guides (they can be hidden under plastic plugs).
3. Lift the drawer and pull towards you. If the buttons are not pressed, try slightly swinging the box left and right.

For drawers BioFresh the algorithm is more complicated:

• 🔴 First remove sealed lid - it is attached with magnets or latches. sides.
• 🔹 Then pull out the drawer and find lock lever on the back wall (usually it is gray).
• 🔄 Press the lever down and at the same time pull the drawer towards you.

In models Liebherr BioFresh with electronic control (for example, SBNes 6256), when removing the drawer, the door open sensor may be triggered. To avoid a system error, after installing the drawer back, reboot the refrigerator (turn it off for 1 minute).

What to do if the drawer is jammed?

If the drawer cannot be removed despite all efforts, check:

1. Guides — perhaps debris (crumbs, ice) has gotten into them.

2. Fixers —in some models they are blocked when If the drawer is skewed, try to align it with the grooves.

3. Temperature —if the refrigerator is operating in the SuperCoolmode, the plastic may shrink and “stick” to the guides. Let it stand for 10–15 minutes at room temperature.

If all else fails, do not use force - contact a service center so as not to damage the mechanism.

How to remove glass boxes with metal handles

Glass boxes (for example, in models Liebherr SBSes 7256 or Monolith) require special care. Their fastenings are usually combined:

• 🔲 Side grooves - as in plastic boxes.
• 🔳 Rear lock - metal or plastic latch that clings to guide.

Instructions:

1. Pull out the drawer until it stops.
2. Lift front part 3-4 cm - so as to release the side grooves.
3. Lower the back of the drawer down (it should come out of the latch).
4. Carefully pull out the box, holding it by the handles.

⚠️ Attention: Do not pull the glass box by the handles at an angle - this may lead to cracks. Always keep it level, distributing the load.

If the drawer is equipped with illumination, before removing, turn off the refrigerator and wait until the lamp has cooled down. In models with LED backlighting (for example Liebherr SBSes 8665), the contacts may be on the guides - do not touch them with wet hands.

Cleaning and reinstallation: nuances

After removing the drawers, they can be washed with warm water and mild detergent. For models with antibacterial coating (for example, BioFresh) do not use abrasive sponges or aggressive chemicals - this will damage the protective layer.

When reinstalling:

• 🔄 Make sure that guides are clean and dry —moisture can cause icing in the models NoFrost.
• 📏 Check that the drawer stands up exactly —misalignment can damage latches.
• 🔊 If you hear a click, it means the box is in place. In models with electronic control, a sound signal may appear.

In refrigerators Liebherr with a system SmartDevice after installing the drawers, sensor calibrationmay be required. To do this:

1. Open the settings menu (usually the button Menu or Settings).
2. Select item Reset settings drawers or Calibration.
3. Confirm the operation - the refrigerator will automatically determine the new parameters.

Common mistakes and how to avoid them

Even with the apparent simplicity of the process, many users make mistakes that lead to breakdowns. Here are the most common ones:

• 💥 Strength instead of technology - trying to pull out the box without releasing the plastic latches often breaks. guides. Liebherr uses fragile latches in models Comfortthat are easy to break.
• 🔌 Ignoring electronics —in refrigerators with a display (for example, SBNes 6256) incorrect removal of drawers can reset the cooling zone settings.
• 🧊 Washing with hot water —the plastic of the drawers Liebherr is designed for temperatures up to 50°C. Hotter water deforms the fasteners.
• 🔄 Mixed-up boxes — if you place the box in the wrong place (for example, from zone 0°C to zone +4°C), this may disrupt the microclimate.

⚠️ Attention: In models with the system NoFrost (for example, Liebherr CN 4013) do not remove the drawers during the defrosting cycle. At this moment, the fan operates at high speeds, and foreign objects can damage the blades.

If after removing the drawer you notice that the refrigerator begins to make more noise or does not maintain temperature, check:

• Do the guides touch fan (relevant for NoFrost).
• Has sensor temperature (in models with electronic control).
• Are there any left inside foreign objects (for example, pieces of plastic from broken fasteners).

FAQ: answers to frequently asked questions

Is it possible to remove drawers in the refrigerator Liebherr, without disconnecting it from the network?

Technically, yes, but this is unsafe. In models with NoFrost the fan can start at any time, and in refrigerators with electronic control (for example, Premiumremoving drawers while the power is on can disrupt the sensor settings. before dismantling.

Why does not the BioFresh drawer come out even though I pressed the lever?

Probably you did not release it completely. magnetic sealTry to slightly swing the drawer left and right while holding the lever pressed. If this does not help, check if it is blocking. drawer closing sensor (in some models it is located on the back wall).

Can Liebherr drawers be washed in the dishwasher?

No, this is strictly not recommended. High temperature and aggressive detergents will damage the plastic and antibacterial coating (if there is one). The exception is boxes made of tempered. glass (for example, in the series Monolith), but it is better to wash them by hand.

What to do if after installing the drawer the refrigerator beeps?

A sound signal usually means that:

• The drawer is installed not completely (check the latches).
• Tripped door open sensor (in models with SmartDevice).
• Broken tightness (relevant for BioFresh).

Try to remove and insert the drawer again. If the signal does not disappear, reboot the refrigerator (turn it off for 1-2 minutes).

Where can you buy replacements for broken drawer latches?

Original spare parts for refrigerators Liebherr sold:

• On branded service centers (guaranteed suitable parts).
• On websites spare parts for household appliances (specify the exact model refrigerator!).
• In some cases, universal fasteners from other brands are suitable (for example, Bosch or Siemens), but this is risky.

The cost of one fastener is - from 200 to 800 rubles depending on the model.