We rehang the door of the Stinol refrigerator yourself: instructions with photos and tips

Reversing the refrigerator door Stinol to the other side is a task that many owners face when moving, renovating, or the banal need to optimize kitchen space. Despite the apparent complexity, the procedure is quite doable with your own hands if you strictly follow the algorithm and take into account the design features of the model. The main thing is to take your time and prepare everything you need in advance.

Most refrigerators Stinol (including the popular series 100, 101, 103, 107, 110 and RF-3xx) support reversible door fastening. However, there are nuances: for example, in models with electronic display on the door you will have to carefully reposition the wires, and in two-chamber units you will have to rehang both leaves separately. If your refrigerator was manufactured before 2010, check for mounting holes on the opposite side - some older modifications simply do not have them.

Before you begin, make sure that rehanging is really necessary. Sometimes the problem with opening the door is solved by simply adjusting loops or rearranging the furniture. If the decision is final, be patient and have the tools. On average, the procedure takes from 1 to 3 hours, depending on experience and model.

Preparation: tools and conditions

For work you will need:

• 🔧 Phillips screwdriver (usually PH2 or PH3) - the main tool for all hinges.
• 🔧 Screwdriver flat (for prying up decorative plugs).
• 🔧 Wrench (usually on 10 mm or 13 mm for the lower hinge bolts).
• 📦 Making tape —to fix the door in the open position.
• 🧲 Magnet (optional)—to hold small fasteners.
• 📸 Smartphone —for photographing stages (useful for reassembly).

Before you start unplug the refrigerator and defrost it (if required). It is more convenient to work on a flat surface - if the kitchen is cramped, move the unit to the center of the room. Make sure that there is an assistant nearby: the refrigerator door Stinol weighs from 8 to 15 kgand it is unsafe to hold it with one hand.

⚠️ Attention! In models with ice maker or water dispenser (for example, Stinol STN RF 385 T) before rehanging it is necessary to disconnect the water supply hoses drain the remaining liquid. Otherwise, you risk flooding the electronics.

If your refrigerator is under warranty, check the conditions of the service center. Some manufacturers consider re-hanging the door non-warranty caseif it is not performed by a specialist.

Door fastening diagram: what you need to know

The design of the hinges Stinol is typical for most domestic refrigerators, but there are key differences from foreign brands:

• 🔹 Upper hinge —usually fixed with two bolts (one on top, one on the side).
• 🔹 Bottom hinge - attached to the body nut (key required) and has adjusting screw for leveling the door.
• 🔹 Middle loop (in two-chamber models) - can be hidden under a decorative trim.
• 🔹 Seal - often used Stinol often used magnetic, which does not require replacement when rehanging.

Feature of refrigerators Stinol — asymmetrical holes for fastening. This means that the plugs on one side may not fit on the other. Check in advance that they are included in the delivery package (usually they are white or gray and hidden under the bottom panel).

Table: Sizes of bolts and keys for popular models Stinol

If your model is not in the table, measure the diameter of the bolts with a caliper or select a key using a trial method. In refrigerators Stinol manufactured after 2015, the lower hinge is often equipped with a plastic sleeve - it must not be lost, otherwise the door will hang!

Step-by-step instructions: removing the old door

We start by dismantling the old fastening. It is important to act consistently so as not to damage the seal and not lose small parts.

Algorithm:

1. Seal the door with masking tape in the open position (at an angle of ~90°).
2. Remove decorative plugs from the hinges with a flat screwdriver (pry it up carefully so as not to break).
3. Unscrew upper hinge bolts with a Phillips screwdriver. Hold the door - it may fall!
4. Lift the door up to remove it from bottom hinge pin.
5. Put the door on a soft surface (for example, a blanket) so as not to scratch it.
6. Unscrew lower hinge hinge with a wrench and remove it from the body.

In two-chamber models (Stinol 107, RF-385) is first removed upper door (freezer compartment), then the lower one. The middle hinge is usually attached to the upper door, so it is unscrewed after dismantling the first door.

⚠️ Attention! In refrigerators with electronic control (for example, Stinol STN 167) inside doors pass the display wires. Do not pull on them - first disconnect the connector (usually it is located under the top hinge).

Moving hinges and plugs to the new side

Now you need to prepare the refrigerator body for installing the door on the other side. The main thing here is not to confuse the holes and distribute the plugs correctly.

Procedure:

1. Remove plugs from the opposite side (where the door will now be). They can fit tightly - pry them out with a screwdriver.
2. Move top hinge to the mirror holes. Secure it not all the way —then you will need adjustment.
3. Install bottom loop and secure with a nut (do not tighten!).
4. If there is one middle loop, move it to the new side, maintaining symmetry.
5. Make sure everything is complete adjusting screws (if any) are in the middle position.

In models Stinol 100/101 the holes for the hinges are symmetrical, but in RF-series they may differ - check the diagram in the instructions. If there are not enough plugs, they can be ordered from the manufacturer (the article number is usually indicated on the plug itself).

What to do if there are no holes on the other side?

In some older models Stinol (before 2005) there are holes for the loops are made on one side only. In this case, you will either have to drill new ones (risky!), or leave the door on the original side. Contact the service center to assess the possibility of modification.

Do not forget about seal: in most cases it does not need to be rearranged, but if the rubber is deformed, replace it with a new one (suitable articles: 6000-000012 for Stinol 100, 6000-000025 for RF-series).

Installing the door on the new side

This is the most important stage. Proceed slowly and be sure to have an assistant.

Instructions:

1. Bring the door to the body and slide it onto the bottom hinge pin.
2. Align the top and insert the bolts top hinge (do not tighten!).
3. Check that the door opens/closes without effort. If there is a skew, loosen the bolts and adjust the position.
4. Tighten all fasteners crosswise (first the top hinge, then the bottom).
5. Install decorative plugs on the new holes.

In two-chamber refrigerators, first install lower door (refrigerator compartment), then the upper middle hinge should move freely, but not. dangle.

If the door opens spontaneouslythen the refrigerator is not level. Level it by twisting front legs.

Adjustment and checking tightness

Even if the door is visually level, it must be adjust checked for leaks. This guarantees proper operation of the refrigerator and saves energy.

How to check the tightness:

• 📄 Take sheet of paper (notebook size).
• 🚪 Close the door, holding the sheet between the seal and the body.
• 🤏 Try to pull out the sheet - if it holds tightly, the seal fits well.
• 🔍 Repeat the test along the entire perimeter of the door.

If the sheet falls out or is pulled out without effort, adjust the hinges:

• 🔧 Loosen the bolts upper or lower hinge (depending on the location of the sagging).
• 📏 Move the door in the desired direction (left/right or up/down).
• 🔩 Tighten the bolts and repeat the test with paper.

In models with electronic display after rehanging, you may need reset errorsTo do this, unplug the refrigerator at 5-10 minutes, then turn it on again.

⚠️ Attention! If after adjustment the door still does not fit tightly, the problem may be deformed sealIn this case, it needs to be replaced. Do not ignore this defect - it causes. to freezing of the evaporator and increased energy consumption.

Common mistakes and how to avoid them

Even if you carefully follow the instructions, you can make mistakes that will lead to incorrect operation of the refrigerator. Here are the most common ones:

Top 5 mistakes when hanging the door Stinol:

• 🚫 Lack of consistency - remove the lower hinge first, not the upper one. This leads to the door falling.
• 🚫 Tightening the bolts is fraught with thread breakage or deformation of hinges.
• 🚫 Ignoring the plugs - open holes collect dust and moisture, which accelerates corrosion.
• 🚫 Incorrect position of the seal —if it is twisted, the door will not be sealed.
• 🚫 Lack of inspection tightness —leads to icing and breakdown of the compressor.

Another typical problem is the door is skewed after installation. It occurs if:

• The hinge bolts are unevenly tightened.
• The refrigerator is standing on uneven surface.
• The seal is worn out and requires replacement.

If, after rehanging the refrigerator started to operate loudly or does not turn off, check:

• 🔌 Is the display connected correctly (for models with electronic control).
• 🌡️ Is thermostat (in mechanical models).
• ❄️ Is there ice on the evaporator (a sign of leakage).

FAQ: answers to frequently asked questions

Is it possible to hang the door on the refrigerator Stinol yourself if you have no experience?

Yes, the procedure does not require special skills, but it will require accuracy and patience. The main thing is to follow the instructions, prepare the tools in advance and work with an assistant. If in doubt, practice unscrewing/tightening the bolts without removing the door.

Do you need to defrost the refrigerator before hanging the door?

It is a must, even if you have a model! c No Frost. Unplug the refrigerator, remove all the food and let the ice melt. This will simplify access to the hinges and prevent short circuits when working with electronic components.

What to do if the door does not close tightly after hanging?

First. check adjustment hinges - loosen the bolts and align the door. If this does not help, inspect seal: it may be dirty or deformed. In extreme cases, replace it (the cost of a new one is from 500 to 1500 rubles, depending on the model).

Is it possible to hang the door on a refrigerator Stinol with a display?

Yes, but you will need to be careful move the wires inside the door. remove them and move the cable to the other side without pulling. In models Stinol STN 167 and RF-385 T the connector for the display is located under the top hinge - it must be disconnected before removing the door.

How much does it cost to rehang the door in service center?

The cost of the service in official services Stinol varies from 1500 to 3500 rubles depending on the model and region. In unofficial workshops, the price may be lower (from 1000 rubles), but there is a risk of damaging the refrigerator. Self-re-hanging will only cost the cost of tools (if there are none) or new plugs. (about 200–500 rubles).