Refrigerators Stinol have long established themselves as reliable and durable helpers in the kitchen, but even with such equipment, users have questions about setting up. Correctly selected temperature conditions not only extend the shelf life of food, but also save energy and prevent ice formation or freezing. In this article, we will look at how to adjust the temperature in a refrigerator Stinol of different models - from classic to modern ones with electronic control.
The manufacturer recommends maintaining a temperature in the main chamber from +2°C to +5°C, and in the freezer - from −18°C to −24°C. However, these values may vary depending on the load on the refrigerator, how often the door is opened, and even the time of year. If you notice that food is freezing slightly and a thick layer of frost is forming on the back wall, it’s time to adjust the settings. Below you will find step-by-step instructions for mechanical and electronic control panels, as well as tips for diagnosing problems.
Types of control panels in Stinol refrigerators
Before you start setting up, determine which control panel is installed in your model. The algorithm of actions depends on this. Refrigerators Stinol are equipped with two types of regulators:
- 🔄 Mechanical regulator - a rotary disk or a lever with divisions (usually from 1 to 7). Found in models Stinol 100, 102, 103, 107 and other budget series.
- 📱 Electronic panel - touch buttons or display (for example, in Stinol RTM 20, STINOL NRTK 185). Allows you to set the exact temperature in steps of 1°C.
In models with a system No Frost (for example Stinol NF 335), the temperature setting can be combined with fan control. If your refrigerator is equipped with two compressors (one for each chamber), adjustment is carried out independently for the freezer and the main compartment.
⚠️ Attention: In refrigerators Stinol with mechanical control The numbers on the regulator do not indicate degrees these are conditional positions, where 1 corresponds to the highest temperature, and 7 to the lowest. The optimal position is usually in the range of 3–4.
Temperature adjustment in models with mechanical controls
Mechanical controls are easy to use, but require manual calibration. In most refrigerators Stinol with this type of control, settings are carried out by one rotary dial located inside the main chamber (less often - on the top panel outside). Here's how to do it correctly:
Find the regulator - it is usually located on the right wall of the refrigerator or under the top shelf. In some models (for example, Stinol 107), the regulator is hidden behind a decorative plug.
Turn the dial clockwise to reduce temperature (increase cold), or counterclockwise to increase temperature (decrease cold).
Set the regulator to position 3–4 (for moderate climates). If the room is hot (above +25°C), move to position 2–3.
For the freezer compartment in models with one compressor (for example, Stinol 102), a separate lever or switch with markings is used Min/Medium/Max. The optimal position is Medium (−18°C). In two-compressor refrigerators (for example Stinol 110), the freezer is regulated by a separate mechanical disk.
Make sure the door closes tightly|
Wait 6-8 hours after changing the settings|
Check the temperature thermometer|
Adjust the position of the regulator if necessary -->
If, after adjustment, ice forms on the back wall in the refrigerator compartment and the food freezes, the regulator is set to too “cold” position. Turn it back 1-2 notches and watch the changes throughout the day.
Temperature adjustment in Stinol refrigerators with electronic control
Electronic control panels allow you to set the temperature with an accuracy of a degree. In models Stinol RTM 20, STINOL NRTK 185 and other series with a display, the setting algorithm is as follows:
Find the buttons
Frige(refrigerator compartment) andFreezer(freezer compartment) on the panel. Some models use a single buttonTempfollowed by selecting a camera.Press the button of the desired camera - the current temperature value will flash on the display.
Use the buttons
+and−(or arrows↑/↓) to set the desired value:- For the refrigerator compartment: +4°C (optimal for most products).
- For the freezer compartment: −18°C (standard for long-term storage).
Confirm your selection with the button OK or wait for automatic saving (after 5-10 seconds).
In refrigerators with a system No Frost (for example Stinol NF 335), an additional parameter may be displayed on the display Super Cool or Fast Freeze. These modes temporarily lower the temperature to quickly cool food, but they are not recommended for use for longer than 24 hours - this increases the load on the compressor.
| Refrigerator model | Control type | Optimal settings | Features |
|---|---|---|---|
| Stinol 100, 102 | Mechanical | Regulator: 3–4 Freezer: Medium |
One compressor, manual defrost |
| Stinol 107, 110 | Mechanical | Refrigerator: 3 Freezer: 4 |
Two compressors, independent adjustment |
| Stinol RTM 20 | Electronic | Refrigerator: +4°C Freezer: −18°C |
Display, function Super Cool |
| Stinol NF 335 | Electronic | Refrigerator: +5°C Freezer: −20°C |
No Frost, automatic defrosting |
⚠️ Attention: If after setting the display shows an errorE1orE2, this may indicate a malfunction of the temperature sensor. In this case, diagnostics by a service center is required.
Optimal temperature conditions for different products
There are no universal settings - the temperature should be selected based on what you store. For example, meat and fish require lower temperatures than fruit or sauces. Here are the zoning recommendations:
- 🥩 Meat and fish: +1°C to +3°C (lower shelves or freshness zone).
- 🥛 Dairy products: +2°C to +4°C (middle shelves).
- 🍎 Fruits and vegetables: +4°C to +6°C (drawers or bottom shelf).
- 🍦 Ice cream: −18°C to −24°C (freezer).
- 🥚 Eggs: +2°C to +4°C (door or special compartment).
In refrigerators Stinol with a freshness zone (for example, Stinol RTM 20), the temperature in this compartment is automatically maintained at 0°C —ideal for greens, berries and perishable foods. If there is no such zone, use the top shelf (the coldest place in the chamber).
Do not forget that overloading the refrigerator leads to uneven cooling. If food is stored close to each other, cold air does not circulate and the temperature in different zones may differ by 2-3°C. Leave gaps between packages and do not fill the chamber more than 70%.
Frequent errors when setting the temperature
Many users encounter problems due to incorrect adjustment. Here are the most common errors and their consequences:
- ❄️ Too low temperature (regulator at 6–7): leads to icing of the back wall, freezing of food and increased energy consumption.
- 🔥 Temperature is too high (regulator at 1): food spoils faster, and the compressor works almost non-stop, trying cool the chamber.
- 🚪 Frequent opening of the door: each time you open the temperature inside rises by 2-3°C. If the refrigerator is loaded, the compressor does not have time to restore the mode.
- 🌡️ Ignoring external conditions: in hot weather or when the refrigerator is located next to the stove, a colder mode is required.
Another typical problem — incorrect position of the regulator after defrosting. Many people forget to return it to its original state, and the refrigerator starts working at maximum power. After any defrosting, check the settings!
What to do if the refrigerator does not cool after setting?
If the temperature does not change despite changing the settings, check:
1. The tightness of the door closure (perhaps the seal is worn out).
2. Fan operation (in models with No Frost).
3. Presence of ice on the evaporator (defrost required).
4. Connect to the network (the thermal fuse may have tripped).
If the problem persists, call a technician to diagnose the compressor or sensors.
How to save energy without damaging storage
Refrigerator Stinol consumes up to 30% of all electricity in the house, but this indicator can be reduced without harm to the products. Here are some proven methods:
Set the temperature in the refrigerator to +4°C, and in the freezer to −18°C. Each degree lower increases energy consumption by 5–7%.
Place the refrigerator away from heat sources (stove, radiator, direct sunlight). The optimal distance to the wall is 5–10 cm for ventilation.
Regularly defrost refrigerators without No Frost (at least once every 6 months). Ice on the evaporator impairs heat transfer and causes the compressor to work harder.
Check the door seal. If it is damaged, cold air escapes and the refrigerator spends more energy cooling. A simple test: close the door, hold up a sheet of paper - if it pulls out easily, the seal needs to be replaced.
In models with electronic control (for example, Stinol RTM 20) there is a function Eco Mode or Energy Saving. By activating it, you will automatically switch the refrigerator to economy mode without manually adjusting the temperature.
Diagnostics of faults by temperature indicators
If the refrigerator Stinol does not maintain the set temperature, this may indicate a breakdown. Pay attention to the following symptoms:
| Symptom | Possible cause | Solution |
|---|---|---|
| The temperature in the refrigerator is above normal, the freezer is working | The refrigerator compartment sensor is faulty or clogged capillary tube | Replacing the sensor or cleaning the system (a master is required) |
| Both chambers do not cool, the compressor does not turn on | Problems with the thermostat or start relay | Checking the electrical circuits, relay replacement |
| The freezer is very cold, the refrigerator is warm | Freon leakage or malfunction of the magnetic valve (in two-compressor models) | Diagnostics for leaks, freon charging |
| The temperature fluctuates, the compressor works non-stop | The thermostat or sensor is faulty | Replacing the thermostat |
If your refrigerator Stinol gives an error on the display (for example, E3 or E4), check it with the instructions. In most cases, this indicates problems with the sensors or fan. For accurate diagnostics, you can use the service menu (in models with electronic control, it is activated by holding the Temp and Super Cool buttons for 5 seconds).
⚠️ Attention: Self-repairing refrigerators with freon (refilling, soldering tubes) is dangerous! Freon is toxic, and improper handling can lead to an explosion. Entrust such work to certified technicians.
FAQ: Answers to frequently asked questions
How to reset the temperature settings to factory settings in a Stinol refrigerator with electronic control?
In most models (for example, Stinol RTM 20), reset is carried out by holding button Temp (or Frige + Freezer) for 10 seconds. After this, the refrigerator will return to standard values: +5°C in the main chamber and −18°C in the freezer. The instructions for your model may indicate another method - for example, a combination Super Cool + Light.
Why is the Stinol 107 refrigerator in the freezer -24°C, and in the refrigerator +10°C?
This is a typical problem for models with one compressor and mechanical control. Most likely, the refrigerator regulator is set to position 1-2 (too warm), or the thermostat is faulty. Try turning the dial to 3-4 and observe for 24 hours. If the temperature does not return to normal, the thermostat needs to be replaced.
Is it possible to turn off the freezer in a Stinol refrigerator if it is not needed?
In two-compressor models (for example, Stinol 110), the freezer can be turned off by turning its control to the position Off or 0. In single-compressor refrigerators (for example Stinol 102), it is impossible to turn off the freezer without turning off the entire system - the compressor cools both chambers sequentially.
How often do you need to defrost a Stinol refrigerator with the No Frost system?
Refrigerators Stinol s No Frost (for example, Stinol NF 335) do not require manual defrosting, but they should still be washed and dried once a year. Turn off the power, remove all products, wash the shelves and walls with warm water and soda, then wipe dry. This will prevent the appearance of unpleasant odors and bacteria.
Why does the Stinol refrigerator make a lot of noise when the temperature changes?
Noise when adjusting the temperature is normal if it is short-term (up to 1-2 minutes). This is where the compressor or fan works (in models with No Frost). If the noise does not stop, check:
- The level of installation of the refrigerator (it must be level).
- Touching of the compressor tubes to the housing or wall.
- Fan clogging (in models with No Frost).
A constant hum or knocking requires diagnosis masters.