We rehang the door of the Veko refrigerator yourself: instructions with photos and tips

Re-hanging the refrigerator door Veko is a task that many owners face when moving, renovating a kitchen, or simply wanting to change the opening side. Despite the apparent complexity, the procedure is quite doable at home if you know the key nuances: from the correct removal of decorative panels to the precise adjustment of hinges after installation. In this article we will look at step-by-step algorithm for models with an upper and lower freezer compartment, pay attention to tools and typical mistakes, and also give recommendations for maintaining the tightness of the seal.

It is important to understand that the design of doors is data-i="51">is different from other brands (for example, Veko different from other brands (eg Atlant or Indesit) - specific loops with locks are often used here. If your model was released after 2018, most likely it comes with instructions with a re-hanging diagram (it can be found on the back wall of the refrigerator or under the vegetable drawers). For older versions, you will have to rely on universal principles, which we will describe below. hidden fastenings and specific loops with clamps. If your model was released after 2018, most likely it comes with instructions with a re-hanging diagram (it can be found on the back wall of the refrigerator or under the vegetable drawers). For older versions, you will have to rely on universal principles, which we will describe below.

Before you begin, answer two questions for yourself:

1. Do you have an assistant? The refrigerator door Veko weighs 15–25 kg - holding it with one hand while unscrewing the hinges is extremely inconvenient.
2. Are you ready for possible adjustments after rehanging? In 30% of cases, it is necessary to tighten the hinges or adjust the position of the seal.

Preparation: tools and safety measures

The work will require a minimum set of tools, but you won’t be able to do without them. The main thing is to use screwdrivers with a magnetic tipso that the screws do not fall inside the refrigerator body. Here is the complete list:

• ⚒️ Phillips screwdriver (size PH2 or PH3 - depends on the model)
• ⚒️ Flat-head screwdriver (for prying up decorative plugs)
• 🔧 10 mm wrench or socket (for some models with bolt loops)
• 📏 Tape measure or ruler (to check gaps)
• 🧲 Magnet (to hold screws and not lose them)
• 🧴 Silicone grease (for hinges after installation)

Before starting work be sure to unplug the refrigerator and free the door from all removable elements: shelves, egg trays, magnets. If the model has a water dispenser (Veko RSF-390, Veko RSF-520), disconnect the water supply hoses according to the instructions. Do not ignore this step —liquid in the hoses may spill when removing the door.

⚠️ Attention: If your refrigerator Veko with a system No Frost, after rehanging the door, additional adjustment of the defrost sensors may be required. In models produced before 2020, the sensors are attached to the door - they will have to be reinstalled.

Work on a flat surface, placing a soft cloth or cardboard under the door to avoid scratching it. If the refrigerator is in a niche, pull it out 50–60 cm for easy access to the hinges. For models with French door (double-leaf) the process becomes more complicated - you will need to remove both leaves one by one.

Hanging scheme: upper and lower hinges

Hinge design y Veko depends on the series of the refrigerator. In most cases, one of two schemes is used:

1. Standard scheme (for models RSF, RSB): the upper hinge is attached to the body, the lower - to the door. When rehanging, both hinges + decorative plugs are swapped.
2. Hidden diagram (for premium series Veko Inox): the hinges are hidden under plastic panels, and the fastenings are duplicated with bolts on the inside of the door.

Consider the universal algorithm for the standard diagram:

1. Removing the top hinge:
   1. Open the door 90°. Use a flat screwdriver to pry off the decorative plug on the top hinge (it usually snaps into place).
   2. Unscrew 2-3 screws holding the hinge. In some models (Veko RSF-350), the screws are hidden under rubber plugs.
   3. Hold the door and remove it from the top pin. Carefully place the door on the prepared surface.
2. Removing the bottom hinge:
   1. Unscrew the screws securing the bottom hinge to the refrigerator body (usually 3-4 screws).
   2. Remove the hinge and move it to the opposite side, having first screwed the screws into the new holes (they closed with plugs).

For models with hidden hinges you will additionally need:

• Remove the inner door panel (snap the clips around the perimeter).
• Unscrew hinge fastening bolts on the inside.
• Move the stops and clamps to the opposite side.

Transfer plugs and fasteners: nuances for Veko

After removing the hinges, there will be holes on the refrigerator body closed with plastic plugs. They must be carefully removed and transferred to the opposite side. In models Veko plugs are of two types:

• 🔳 Snap-on (removed with a flat screwdriver, inserted until it clicks).
• 🔳 Screw (screwed with a small self-tapping screw, require care when unscrewing).

Pay attention to holes for hinges —they may not be symmetrical. For example, in refrigerators Veko RSF-450 the holes for the top hinge are shifted 5 mm to the left for better tightness. When transferring hinges to the other side, this must be taken into account:

If there are no holes on the opposite side, you will have to drill them yourself. To do this:

1. Attach the loop to the attachment point and mark the centers of future holes with a pencil.
2. Use a drill with a diameter of 4–5 mm (for most models Veko).
3. After drilling, stick the rubber gaskets from the kit on the holes (they prevent corrosion).

⚠️ Attention: In refrigerators with display on the door (Veko Smart) when rehanging, it may be necessary to relocate the wiring. Do not pull the wires - disconnect the connectors carefully, having first photographed their location.

Installing the door on the new side: step by step

Now that the hinges and plugs have been transferred, you can begin reassembling. Follow this algorithm:

1. Installing the bottom hinge:
   1. Insert the bottom hinge pin into the hole on the refrigerator body.
   2. Hold the door, slide it onto the pin and secure with screws (do not tighten it completely!).
2. Installing the top hinge:
   1. Lift the door so that the top pin fits into the hinge groove.
   2. Tighten the screws crosswise to avoid distortion.
3. Checking the tightness:
   1. Close the door and check whether the seal fits evenly around the entire perimeter.
   2. If there are gaps, adjust the hinges (see next section).

Critical point: in refrigerators Veko with a system Multi Air Flow after re-hanging the door, the distribution of air flows may be disrupted. If you notice that the products in the upper compartments are freezing, check the position of the flaps on the back wall.

For models with French door the process is complicated by the need to synchronize both flaps. A simple rule will help here: first it is installed Left door (if you look at the refrigerator), then the right one is adjusted to its level. Use a building level to check the horizontal position.

Adjusting hinges and seals: how to avoid misalignment

Even with careful installation, the door may sag or not close tightly. This is due to:

• 🔧 Uneven tightening of the hinge screws.
• 🔄 Deformation of the seal (especially if the refrigerator has been in use for a long time).
• 📏 Warping of the case (check the evenness of the floor!).

To adjust:

1. Upper hinge: Loosen the screws and slightly raise or lower the door, then tighten the screws again. This will help align it vertically.
2. Bottom hinge: Tighten the adjusting bolt (usually located on the side) to adjust horizontally.
3. Sealant: If the rubber is deformed, warm it up use a hairdryer (temperature 50–60°C) and shape it with your hands. As a last resort, replace with a new one (the seal article for Veko usually begins with VEKO-SEAL-...).

Check the tightness using test with a sheet of paper:

1. Insert a sheet of paper between the seal and the body.
2. Close the door and try to pull out the sheet.
3. If the sheet comes out easily, the seal needs adjustment or replacement.

⚠️ Attention: In refrigerators Veko s function Super Cooling after reversing the door, an alarm may sound due to a leak. Reset the error by holding the button Super Cool 5 seconds.

What to do if the door still sags after adjustment?

If after several attempts to adjust the door continues to sag, the problem may be in worn-out hinges. In this case, they will need to be replaced. For models, original hinges can be ordered according to the part code, which is indicated on the hinge itself or in the refrigerator passport. An alternative is universal hinges from Veko original hinges can be ordered using the part code, which is indicated on the hinge itself or in the refrigerator passport. An alternative is universal hinges from Samsung or LG, but they may not fit. pin size.

Typical mistakes and how to avoid them

Even experienced craftsmen sometimes make mistakes when hanging doors Veko. Here are the most common:

• 🔨 Tightening the screws — leads to deformation of the plastic hinge bushings. Solution: use a torque wrench with a force of no more than 2 Nm.
• 🔄 Ignoring stubs - open holes violate the thermal insulation. Solution: remove all plugs, even if they seem "unnecessary".
• 🚪 Wrong order assembly - install the lower loop first, then the upper one. Solution: Follow the instructions strictly step by step.
• 🔌 Forget to turn off refrigerator —risk of short circuit when working with metal tools. Solution: unplug the plug from the socket to start work.

Another common problem is when removing the door. If the rubber is torn or has lost elasticity, it will have to be replaced. Seals are suitable. the following types: damage to the seal when removing the door. If the rubber is torn or has lost elasticity, it will have to be replaced. For Veko The following types of seals are suitable:

If after rehanging the refrigerator began to make more noise, check:

• 🔊 Compressor - it may have shifted when moving the refrigerator.
• 🌀 Fan (in models with No Frost) - could touch ice or wires.
• 🧲 Magnetic seal - if installed incorrectly, creates vibration.

Features for models with a dispenser and No Frost

Refrigerators Veko with a water dispenser (Veko RSF-520W, Veko RSF-600W) require additional manipulations:

1. Turn off the water supply and drain the residue from the hose.
2. Disconnect the tube from the back wall of the door (it is attached plastic retainer).
3. Move the tube to the other side using the standard holes (they are closed with plugs).
4. Check the tightness of the connections after installation - leaks can lead to a short circuit!

For models with No Frost (Veko RSB-390NF, Veko RSB-520NF) important:

• ❄️ Move the door temperature sensor (it is mounted on clips inside the case).
• 🌀 Check the position of the fan - it should not touch the walls after rehanging.
• 🔄 Reset defrost settings (hold the button No Frost 10 seconds).

If your refrigerator is equipped with electronic display (Veko Smart Inox), sensor calibration may be required after rehanging. To do this:

1. Enter the service menu by holding the buttons Super Cool + Light 5 seconds.
2. Select item Door Calibration (navigation with the "+" and "–").
3. Follow the instructions on the screen (usually you need to open and close the door 3 times).

⚠️ Attention: In refrigerators Veko with the function Smart Diagnosis after reversing the door, an error may appear dE (door error). Reset it by unplugging the refrigerator for 1 minute.

FAQ: answers to frequently asked questions

Is it possible to hang the refrigerator door Veko without an assistant?

Technically, yes, but it is extremely inconvenient. The door weighs 15–25 kg, and it is almost impossible to hold it with one hand while unscrewing the hinges. If there is no assistant, use rubber fastener straps (for example, from the trunk of a car) to hang the door from the top of the refrigerator while working.

What to do if, after hanging, the door does not close tightly?

Reasons may be different:

1. The hinges are tightened unevenly - loosen the screws and adjust the position of the door.
2. The seal is deformed - heat it with a hairdryer (temperature 50–60°C) and restore its shape.
3. The refrigerator body is not level - check the level floor and adjust the legs.

If the problem persists, the hinge or seal may be damaged - replacement will be required.

Do I need to hang the freezer door separately?

In most models Veko the freezer compartment has a separate door, and it can also be hung. The process is similar, but there are nuances:

• In models with lower freezer (Veko RSB), first the upper door is hung, then the lower one.
• In refrigerators Side-by-Side (Veko SBS-600) both doors are re-hung at the same time, since they are connected by a common loop.

For freezers with vacuum seal (for example, Veko RSF-520F) after rehanging, it is recommended to check the tightness using a test with a sheet of paper (see section above).

How long does it take to rehang the door?

On average, the procedure takes:

• 1–1.5 hours for standard models (Veko RSF-390, Veko RSB-450).
• 2–3 hours for refrigerators with a dispenser or No Frost (Veko RSF-520W, Veko Inox 600).
• 3-4 hours for Side-by-Side or French doors (Veko SBS-600, Veko RFD-550).

If you are doing this for the first time, allow extra time for adjustments and checking tightness.

Is it possible to hang the door by refrigerator Veko with touch control?

Yes, but with reservations:

1. Unplug the refrigerator and reset the settings (hold the button Power 10 seconds).
2. Move the touch panel to the other side, following the diagram in the instructions (it is usually glued to the back wall).
3. After installation, calibrate the sensor: enter the service menu (buttons Super Cool + Eco) and select Touch Calibration.

In models Veko Smart Touch (2021 and newer), the touch panel is attached with magnets - its transfer does not require additional tools.