After purchasing a new one of household appliances or their delivery after repair, owners are often faced with the need for a correct first start-up. Hotpoint Ariston refrigerator - this is complex equipment that requires compliance with certain time intervals before applying voltage. Ignoring transportation rules can lead to failure of the compressor, so rushing in this matter is unacceptable.
In this article we will analyze in detail the algorithm of actions that will help you safely activate the device and get into operating mode. You will learn why it is important to wait time after delivery, how to position the unit correctly, and what settings are required immediately after plugging it into the network.
Compliance with these simple but critical steps will ensure the long service life of your Hotpoint Ariston and maintaining the manufacturer's warranty. Let's look at each stage of preparation and launch in detail to eliminate any risks of breakdown of expensive equipment.
Waiting time after transportation
The first and most important rule is: you cannot turn on the device to the power supply immediately after it has been brought into the apartment. When transported in a horizontal position or with strong shaking refrigeration oil it could flow from the compressor crankcase into the pipe system and the evaporator circuit. If you start the engine at this moment, it will work without lubrication, which will lead to rapid wear or jamming of the piston group.
The time that must be waited directly depends on the position in which the unit was transported. If the device was standing vertically and was not tilted more than 40 degrees, it is enough to wait 2-3 hours for the temperature of the internal components to stabilize. However, during horizontal transportation or strong tilt the minimum settling time should be at least 8-12 hours, and ideally - a full day.
⚠️ Attention: An attempt to turn on the unit earlier than the recommended time may result in denial of warranty service. Service centers can easily determine whether a compressor is operating “dry” by characteristic signs of wear.
In addition, during downtime, the smell of new plastic and packaging, which is often present inside the chambers immediately after unpacking, will have time to disappear. Just leave the doors open in a well-ventilated area while you wait for power to be served.
Preparation for the first start
Before inserting the plug into the socket, it is necessary to carry out a number of preparatory manipulations with the case itself and the internal space. Installing the refrigerator should be done on a flat, hard surface surface. If the floor is uneven, be sure to adjust the height of the front supports using the special key included in the kit or a regular screwdriver.
Correct adjustment of the legs ensures not only stability, but also the correct closing of the doors under the influence of gravity. The door Hotpoint Ariston should close on its own if opened at an angle of less than 45 degrees. Also make sure that there is a gap of at least 10 cm between the back wall of the case and the wall of the room or furniture for free air circulation.
☑️ Check before turning on
The internal shelves and drawers should be wiped with a soft damp cloth using a weak solution of soda or a special product for household appliances. This will remove any dust that may have gotten inside during unpacking. Do not use abrasive cleaners, as they can damage the plastic coating or glass of the shelves.
Connecting to the electrical network
After the necessary waiting time has passed and preparation has been carried out, you can proceed with the electrical connection. Socket, in which the refrigerator will be connected must be in good working order, be grounded and match the load capacity device. Typically, household models consume little energy, but power surges can be dangerous for electronics.
It is strictly not recommended to use extension cords, tees or low-quality surge protectors to connect powerful household appliances. The best option is a separate outlet located in close proximity to the installation site. The plug should fit tightly, without play or sparking.
| Parameter | Normal | Critical value |
|---|---|---|
| Network voltage | 220-230 V | Less than 190 V or more than 250 V |
| Grounding | Required | Absent |
| Cord condition | No damage | The insulation is broken |
If power outages or power surges often occur in your area, it makes sense to think about installing a stabilizer. The electronic control module Hotpoint Ariston is sensitive to the quality of the power supply, and surges can damage the control board.
Indication and sound signals
Immediately after you connect Hotpoint Ariston refrigerator to the network, it may not behave as expected. The indicators on the control panel may light up and a beep may sound from the speakers. Don’t be alarmed, this is a standard reaction of the self-diagnosis system.
A sound signal (squeak) usually means that the temperature inside the chambers is higher than the established norm, which is quite logical, because the unit has not yet started cooling. A squeak may also indicate that the door is open. To turn off the sound, press the corresponding button on the control panel or simply close the door tightly.
⚠️ Attention: If the sound signal does not stop after closing the door and resetting the alarm with the button, check the tightness of the seal. Foreign objects or misalignment of the door may prevent it from sealing properly.
The temperature indicators may flash on the display. This means that the process of reaching the regime is underway. Depending on the model, the current temperature value or operating mode symbols (Super Freeze, Eco) may flash. After some time, when the temperature drops to the set values, the indication stabilizes.
Setting the temperature mode
After turning on the compressor, you need to set the optimal operating parameters. Factory settings may not suit your needs or current room temperature. Adjustment is carried out through the control panel, which, depending on the model Hotpoint Ariston can be electronic (with a display) or mechanical (rotary control inside the camera).
For electronic panels, use arrow buttons or "Temp" touch zones. It is recommended to set the following values for normal food storage:
- 🌡️ Main compartment: +4°C ... +5°C (optimal for most products).
- ❄️ Freezer compartment: -18°C ... -20°C (standard for deep freezing).
- 🥗 Freshness zone (if any): 0°C ... +2°C (for meat, fish and vegetables).
If you have a model with a mechanical regulator (usually a knob with numbers from 1 to 5 or from Min to Max inside the refrigerator compartment), remember: a larger number means a lower temperature (more intense cold). To begin with, set the regulator to the average value (for example, “3”), let the refrigerator operate for a day, and then adjust if necessary.
What is the Super Freeze mode?
The Super Freeze mode forces the compressor to operate continuously to quickly reduce the temperature. It is used when loading large quantities of fresh products. Do not keep this mode turned on constantly, so as not to overload the compressor and not overfreeze the food.
Time to enter operating mode
You should not expect instant cooling immediately after switching on. Refrigeration unit It takes time to cool the internal volume, shelves and walls of the chambers to the specified temperatures. Typically, this process takes from 4 to 12 hours, depending on the temperature in the room, the volume of the chambers and the number of loaded products.
During the first hours of operation, the compressor can work almost non-stop. This is fine. The system tries to gain cold as quickly as possible. After reaching the target temperature, the engine will turn on and off cyclically, maintaining the mode.
It is recommended to load a full load of food only after the refrigerator has been running for several hours idle or with a minimum amount of cargo. A sudden filling with warm products will cause the compressor to work under overload for a long time.
Frequent problems when turning on for the first time
Even when turned on correctly, users may encounter phenomena that are mistaken for a malfunction. Understanding the physics of work Hotpoint Ariston will help you avoid unnecessary calls to service.
One of the common “problems” is heating of the side walls or partitions between the chambers. This is not a defect, but a design feature where the condenser tubes pass through the walls. The release of heat to the environment is a necessary process for the operation of the refrigeration cycle.
Gurgling, bubbling or noise of flowing liquid inside may also be observed. This is the sound of refrigerant circulating through the system. In modern models with quiet compressors, this sound can be heard even more clearly than the noise of the motor.
- 💧 The appearance of water under the refrigerator: check whether the condensate drain hole inside the chamber is clogged.
- 💨 Whistle or buzzing: may be caused by improper installation (shipping seals are not unscrewed bolts, if any, or the legs are not adjusted).
- ❄️ Ice formation on the back wall: in drip systems this is a normal defrosting process, the ice melts and flows into the drain.
⚠️ Attention: If you notice a burning smell, strong vibration, knocking or sparking in the compressor area - immediately disconnect the device from the network and contact an authorized service center.
Questions and answers (FAQ)
How long can you not turn on the Hotpoint Ariston refrigerator after purchase?
The minimum waiting time is 2-3 hours if the refrigerator was transported vertically. If transportation was carried out lying down, you must wait at least 8-12 hours, or better yet 24 hours, for the oil to drain back into the compressor.
Why does the refrigerator hum immediately after turning on?
Humming is the normal sound of a running compressor. However, if the sound is accompanied by strong vibration, check whether the refrigerator is level. Adjust the legs so that the body does not wobble and does not touch walls or furniture.
Do you need to wash the refrigerator before first use?
Yes, definitely. Wipe all interior surfaces, shelves and drawers with a damp cloth and mild detergent to remove manufacturing dust and new plastic odors. Let the cameras dry before turning them on.
What to do if the red alarm indicator is on?
The red indicator indicates an increase in the temperature inside the cameras. When you turn it on for the first time, this is normal because the refrigerator has not yet cooled down. Press the alarm reset button (usually a crossed out triangle) and the indicator will go out when the temperature drops to normal.
Is it possible to immediately load food into a new refrigerator?
Not recommended. Let the refrigerator run idle for 2-4 hours until it reaches operating temperature. Loading warm products immediately after switching on will increase the cooling time and the load on the compressor.