Reversing the doors of an LG refrigerator: instructions with photos and expert advice

Re-hanging refrigerator doors LG is a task that many owners face when moving, renovating a kitchen or a banal desire to optimize space. Despite the apparent complexity, the procedure is quite doable at home if you know the key nuances of the design and avoid common mistakes. In this article, we will analyze the process step by step: from preparing the tools to the final adjustment of the hinges, and also tell you which models LG support this option, and where it is better not to risk it.

It is important to understand that not all refrigerators LG allow you to hang the doors - it depends on the series and year of manufacture. For example, in models with a system Door-in-Door or built-in water dispensers, the process becomes more complicated, and sometimes completely impossible without the intervention of a service center. Before you begin, check for the presence of holes for attaching hinges on the opposite side - their absence indicates that the manufacturer has not provided such an option.

If you have never done such work, do not worry: our guide will take into account even little things like maintaining the tightness of the seal or the correct position of the cables in models with electronic control. And for those who doubt their abilities, we have prepared a checklist with criteria under which it is better to turn to professionals.

Which LG models support door reversal?

Not all refrigerators LG allow door reversal. Here are the key criteria to determine whether the procedure is possible for your model:

• 🔹 Series without a dispenser: Most classic models (for example LG GA-B489, GA-B429) have symmetrical hinge holes on both sides of the case. The exception is models with LED display on the door, where the transfer of electronics is required.
• 🔹 Side-by-Side: In refrigerators with vertical division (for example, LG GS-X961, GS-L601), you can only move both doors at the same time — a separate procedure is not provided.
• 🔹 Door-in-Door: Models with an internal door (series InstaView) usually do not support overhanging due to the complex design of the seal and opening mechanism.
• 🔹 Built-in models: Here it all depends on the manufacturer of the kitchen set - often the refrigerator door is attached to the facade of the furniture, and its overhanging requires dismantling the entire systems.

To be sure, inspect the upper and lower parts of the refrigerator from the side - if there are plugs or holes for bolts, it means that re-hanging is possible. Otherwise (for example, in models LG Signature with touch control), attempting to dismantle yourself may lead to loss of warranty.

⚠️ Attention: In refrigerators LG with a system Smart ThinQ (for example, LG InstaView ThinQ) doors may damage sensors or display power cables. Before starting work, disable the Wi-Fi function in the settings to avoid software crashes.

Preparation: tools and safety

To hang the refrigerator doors LG you will need:

• 🔧 Phillips and flathead screwdrivers (size depends on the model, but PH2 and SL4).
• 🔨 Wrench 10 or 12 mm - for hinges of some series (for example, LG GB-B579).
• 📏 Level (preferably laser) - so that the door hangs evenly after installation.
• 🧲 Magnet or tape —for temporary fastening of removed parts (screws, plugs).
• 🧴 Silicone grease —for processing the seal after rehanging.

Before starting work, be sure to:

1. Unplug the refrigerator and let it stand for 1-2 hours - this will prevent damage to the compressor if it is turned on accidentally.
2. Remove all products and shelves from the door (eggs, bottles, etc.) so as not to drop them during dismantling.
3. Prepare the workspace - place a soft cloth on the floor so as not to scratch the body when removing the door.

If your refrigerator is equipped electronic display (for example LG GR-B247), pay attention to the wires going from the door to the body. They should not be pulled or twisted - this can damage the control panel. In such cases, it is better to invite a specialist.

Step-by-step instructions: remove and rehanging the door

The process of rehanging refrigerator doors LG consists of several stages. We will analyze a universal algorithm that is suitable for most models (for example, LG GA-B489, GA-B429, GB-B579for refrigerators with a dispenser or system No Frost additional steps may be required - we will consider them). separately.

Step 1: Removing the top hinge

Start with the top hinge - it is usually secured with 2-3 screws. Carefully unscrew them with a Phillips screwdriver, holding the door so that it does not fall. In some models (for example, LG GS-L601) the loop can be closed with a decorative cover - it needs to be pryed off with a flat screwdriver.

After removing the hinge, remove plugs from the opposite side of the case (they cover the mounting holes. Save them - you will need them). to install the hinge in a new location.

Step 2: Removing the door

Now carefully lift the door up to free it from the lower hinge In models with double door (for example, LG GC-B247) first the inner part is removed, then the outer part. If the door is “jammed”, do not force it - check that all screws are unscrewed and lubricate the hinges WD-40.

Place the door on a soft surface (for example, a blanket) with the front side up to avoid damage. seal.

Step 3: Moving the hinges to the other side

Move the top and bottom hinges to the opposite side of the body using the existing holes. Screw in the screws, but do not tighten them completely - the door should “play” freely for subsequent adjustment.

On models. c electronic control (for example, LG GR-B247) at this stage you will need to move the display power cables. To do this:

1. Disconnect the connector on the back wall of the door.
2. Route the cable through the new hole. in the hinge (usually it is closed with a plug).
3. Connect the connector back, making sure that the wires are not strained.

Step 4: Installing the door and adjusting

Place the door onto the lower hinge, then carefully lower it, aligning it with the upper one. Tighten the screws, but not all the way - leave some play for adjustment.

Use levelto check the horizontal position of the door. If it is skewed, loosen the screws and adjust the position of the hinges. In models LG with the system Smart Cooling (for example, LG GB-B579) it is important that the gap between the door and the body is the same around the entire perimeter - this ensures proper air circulation.

Features for refrigerators with a dispenser and No Frost

Refrigerators LG with a water dispenser (LG GR-B247, GC-B247) or system No Frost require additional manipulations when hanging the doors. Here are the key nuances:

• 💧 Dispenser: Before removing the door, turn off the water supply and drain the remaining water from the tube (the tap is usually located on the back wall of the refrigerator). After rehanging, check the tightness of the connections - leaks can damage the electronics.
• ❄️ No Frost: In models with this system (for example, LG GA-B489) there are air ducts inside the door. When dismantling, make sure that they do not bend - this will disrupt air circulation and lead to freezing.
• 🔌 Electronic modules: In refrigerators with touch control (series LG Signature), it may be necessary to reconfigure the sensors after rehanging. To do this, hold down the button Child Lock for 5 seconds - this will reset the errors.

If your model is equipped with ice generator (for example, LG GR-B247), please note that after re-hanging may require reinstalling the cube tray. In some cases, it will have to be rotated 180 degrees - for this, the kit usually includes additional fasteners.

⚠️ Attention: In refrigerators LG with function Smart Diagnosis (for example, LG InstaView ThinQ) after re-hanging the doors, an error may occur dH (door sensor malfunction). To reset it, unplug the refrigerator for 10 minutes, then turn it on again.

Typical mistakes and how to avoid them

Even if the instructions are followed, owners often make mistakes that lead to breakdowns or incorrect operation of the refrigerator. Here are the most common of them and ways to prevent them:

Another common problem is extraneous sounds after re-hanging (creaking, knocking). They usually occur due to:

• 🔊 Insufficient lubrication of the hinges —use WD-40 or special lubricant for refrigerators.
• 🔊 Debris gets into the mechanism —clean the hinges brush before installation.
• 🔊 Incorrect position of the magnetic seal —it should fit evenly around the entire perimeter.

In LG refrigerators with the Linear Cooling system (for example, LG GC-B247) after reversing the doors, cooling may be temporarily reduced due to changes in air circulation. This is normal - after 12–24 hours the work returns to normal.

When is it better to call a specialist?

Despite the apparent simplicity, there are situations when re-hanging the refrigerator doors LG is best left to professionals. Contact the service center if:

• 🛠️ Your model is equipped with touch display or system Door-in-Door —there is a high risk of damaging the electronics.
• 🛠️ The refrigerator is under warranty - independent repairs can void it.
• 🛠️ You found corrosion on the hinges or damage to the case - this may indicate more serious problems.
• 🛠️ After re-hanging, errors appeared on the display (for example, Er FF or dH) - they indicate a failure in the system.

The cost of re-hanging doors in service centers LG varies from 1 500 to 3,500 rubles depending on the model and region. In some cases (for example, if the seal is damaged), parts may need to be replaced - this will increase the price by 1,000–2,000 rubles.

⚠️ Attention: If, after rehanging, the refrigerator LG becomes worse at freezing or condensation appears on the walls, immediately return the door to its original position and contact service. This may indicate depressurization of the system or damage to the refrigerant pipes.

Care after rehanging: tips for extending service life

To ensure that refrigerator doors LG last long after rehanging, follow these recommendations:

• 🧼 Cleaning the seal: Once a month Wipe the rubber seal with soapy water, then lubricate with silicone grease. This will prevent cracking and loss of tightness.
• 🔧 Checking the hinges: Every 6 months, tighten the hinge screws - over time they become loose from compressor vibration.
• 🌡️ Temperature control: If, after rehanging, the refrigerator takes longer to gain cold, check whether the ventilation duct is blocked (in models with No Frost).
• 🚫 Avoid overload: Do not hang heavy objects on the door (for example, bottles with a volume of more than 1.5 liters) - this will deform the hinges.

In models with with a dispenser (LG GR-B247) after reweighing, the water pressure may change. Adjust it using the screw on the back of the refrigerator (instructions are in the user manual). If water does not flow at all, check whether the hose is kinked when installing the door.

FAQ: Frequently asked questions about reversing LG doors

Is it possible to rehang only one door in an LG Side-by-Side refrigerator?

No, in models LG Side-by-Side (for example, GS-X961) the hinges of both doors are interconnected. Hanging only one door will upset the balance and may cause the frame to warp. In such cases, it is necessary to dismantle and move both hinges at the same time.

What to do if, after rehanging, the door of the LG refrigerator does not close tightly?

The reasons may be the following:

1. The seal is deformed - warm it with a hairdryer (t ≤ 50°C) and lubricate with silicone grease.
2. The door is skewed - loosen the hinge screws and adjust the position using a level.
3. Debris has gotten into the hinges - clean the mechanism and lubricate WD-40.

If the problem persists, check if the refrigerator body is bent when dismantling.

Is it necessary to reprogram the electronic panel after rehanging the doors?

In most models LG (for example, GA-B489) reprogramming is not required. However, in refrigerators with Smart ThinQ (for example, InstaView ThinQ), a door sensor error (dH) may occur. To reset it, unplug the refrigerator for 10 minutes, then turn it on again. If the error remains, contact the service.

How long does it take to rehang the doors of an LG refrigerator?

On average, the procedure takes from 1 to 3 hours depending on the model:

• 1 hour - for simple models without a dispenser (for example, LG GA-B429).
• 2-3 hours - for refrigerators with electronic control or system No Frost (for example, LG GR-B247).

If you have never done such work, take some time - there may be delays in adjusting or eliminating minor errors.

Is it possible to reverse the doors of an LG refrigerator with an ice maker?

Yes, but this will require additional action:

1. Turn off the water supply and drain the remaining residue from the tube.
2. Move the ice tray to the other side (the kit usually includes fasteners for this).
3. Check the tightness of the connections after installation - leaks can damage the generator.

B models LG with double ice maker (for example, LG LFXS26973S) door reversal is not provided by the manufacturer.