We move the LG refrigerator door to the other side: instructions with photos and tips

Repositioning the refrigerator door LG to the other side - a task that many owners face when moving, renovating, or simply wanting to optimize space in the kitchen. Despite the apparent complexity, the procedure is quite doable with your own hands if you know the key nuances: from preparing tools to fixing hinges and aligning the seal. In this article, we will analyze a step-by-step algorithm for models with mechanical control, No Frost and a water dispenser, and also reveal typical errors that lead to distortions or loss of tightness.

Important: the design of hinges and fasteners may differ depending on the refrigerator series (for example, LG Door-in-Door or Instaview require a special approach). If your model was released after 2020, check for electronic sensors in the door - disabling them incorrectly may cause system malfunctions. To accurately identify the rehanging scheme, use serial numberindicated on the sticker inside the chamber or on the back panel.

Before you begin, evaluate your strength: the procedure takes from 1 to 3 hours and requires care. If the refrigerator is under warranty, independent intervention may void it - check this point with the service center LG.

Preparation: tools and conditions

To rehang the refrigerator door LG you will need:

• 🔧 Phillips screwdriver (usually PH2) - for most models.
• 🔧 Hex key (size 4 or 5 mm) - for hinges of some series (for example, LG GR-B207).
• 📏 Level (bubble or laser) - to avoid warping the door.
• 🧲 Magnetic screwdriver or tweezers —for removing small fasteners.
• 🧴 Silicone grease (optional)—for processing hinges after installation.

Also prepare:

• 📦 Cardboard or soft fabric —to avoid scratching the floor and body of the refrigerator when laying the door.
• 🧊 Thermal insulating tape —for temporary fixation of the seal, if it is removable.
• 🔌 Assistant —the refrigerator door weighs 10–20 kg, and holding it with one hand is inconvenient.

⚠️ Attention: If your refrigerator is equipped with with a water dispenserbefore rehanging be sure to turn off the water supply and drain the remaining water from the tube through the dispensing button. Otherwise, when removing the door, a leak may occur!

Carry out work in a well-lit room. If the refrigerator is in a niche, pull it out 50–60 cm for free access to the hinges. In advance defrost both chambers (if the model is not No Frost) and unplug it - this will prevent a short circuit if moisture accidentally gets on the contacts.

Step 1: Removing the upper door (freezer)

On most models LG the rehang begins with top door (freezer) This is due to the fact that the lower door of the refrigerator is attached to the middle hinge, which is fixed on the upper door. with French door (double-leaf), where the algorithm is different.

Removal instructions:

1. Open the top door 90° Place it under it. cardboard or towel so as not to damage the floor.
2. Remove decorative plugs from the hinges (they usually snap into place - pry them off with a flat-head screwdriver).
3. Unscrew fastening bolts upper hinge (usually 2-3 pieces). In some models (for example, LG GC-B247), you first need to remove the hinge cover by unscrewing it from the inside of the door.
4. Holding the door, carefully remove it from the lower hinge pin and place it on prepared surface.

If the door “jams” when removing, do not use force! You probably missed one of the bolts or did not completely remove the pin. Check:

• 🔍 All fasteners have been removed (sometimes the bolts are hidden under stickers).
• 🔍 Doesn't interfere. whether seal —it can be temporarily bent.
• 🔍 Are there additional latches on models with electronic display (for example, LG InstaView ThinQ).

Step 2: Removing the middle hinge and lower door

After removing the upper door, proceed to middle hinge, which secures the lower door of the refrigerator. It is important here not to confuse the order. actions:

1. Remove decorative trim the middle hinge (it can be fixed with latches or screws).
2. Unscrew the bolts holding loop on the refrigerator body (usually 2-4 pieces). In models with dispenser the water supply hose passes here - carefully disconnect it, first squeezing the clamp.
3. Remove the middle loop and set it aside. rubber gaskets —they may fall out during dismantling.
4. Now unscrew the bolts of the lower hinge and remove the lower door, holding it by the handle.

At this stage, a problem often arises with electrical wiring (in models with a display or sensors). If you see a bundle of wires going from the door to the case:

• 🔌 Carefully disconnect the connectors after photographing their location.
• 🔌 Do not pull the wires - they may be soldered to the board. control.
• 🔌 If the connector is “stuck,” use a plastic spatula to loosen it.

⚠️ Attention: In refrigerators LG with Smart Diagnosis system (for example, LG GB-B539) inside the door can be installed microphone to transmit data about malfunctions. When removing the door, do not drop it - the impact may damage the electronic module!

Step 3: Transferring the hinges to the other side

Now it is necessary to move the hinges to the opposite side. This stage requires precision, since the smooth movement of the door depends on the correct position of the hinges. tightness and smooth door movement.

Transfer algorithm:

1. Remove plugs from the holes on the other side of the refrigerator (they can be hidden under stickers or rubber stoppers).
2. Move the hinges to the new side, aligning the holes. Pay attention to marking: on some hinges there are marks “L” (left) and “R” (right).
3. Tighten the bolts, but do not tighten them all the way - first you need to align the door.
4. If included rubber gaskets, install them on new holes (they prevent vibration).

Features for different series:

In models LG 2022–2026 (for example, LG GR-B267) the middle loop may have asymmetrical design —it cannot simply be turned over. In this case, you will need to disassemble the hinge and swap its halves.

Step 4: Installing doors on new hinges

At this stage, it is important to follow the sequence and control gaps between the door and the body. Start with the bottom door:

1. Install the bottom door onto the bottom hinge pin, holding it by the handle.
2. Align the door vertically using a level. A deviation of more than 2 mm can lead to spontaneous opening.
3. Tighten the bolts of the lower hinge, but not all the way - leave some play for adjustment.
4. Install the middle hinge, aligning it with the fasteners on the lower door. Tighten the bolts.
5. Place the top door onto the middle hinge, then fix the top hinge.

Check:

• 🔄 Smooth operation —the door should open without jerking.
• 📏 Gaps — there should be a uniform clearance of 1–2 mm around the entire perimeter.
• 🔊 Sounds —creaks or clicks indicate skewed hinges.

⚠️ Attention: If after installation the door opens on its own at an angle of more than 45°, this is a sign improper adjustment of the hinges. Do not leave it like this - over time the hinges will become deformed!

Step 5: Adjusting and checking the tightness

Even if the doors are visually level, they need to adjust checked for tightness. To do this:

1. Adjust the gaps:
   • If the door fits too tightly, loosen the hinge bolts and move it a little.
   • If there are gaps, tighten the bolts or add rubber gaskets.
2. Check the seal:
   • Run around the perimeter of the door with a sheet of paper —it should press tightly.
   • If the seal is deformed, warm it up hairdryer (temperature 50–60°C) and shape.

Self-opening test:

• Open the door 30° and release - it should remain in this position.
• If the door closes by itself, loosen the top hinge.

For models with dispenser additionally check:

• 💧 Water leakage - after connecting the hose, fill a glass of water and make sure there is no leakage.
• 🔋 Display operation —if after rehanging the screen does not turn on, check the wire connection.

If the seal is damaged or has lost elasticity, it can be restored:

How to return the seal to its shape without replacement

Immerse the seal in hot water (70–80°C) for 5–10 minutes, then shape it and secure with tape until it cools completely. This method works if the rubber is not cracked.

Typical mistakes and how to avoid them

Even when following the instructions, you can make mistakes that will lead to problems the operation of the refrigerator. Let's look at the most common ones:

Error	Consequences	How to fix
Wrong sequence of door removal	Disk of the middle hinge, difficult opening	Remove both doors and reinstall, starting from the bottom
Tightening the hinge bolts without alignment	Door opens by itself or does not close	Loosen bolts, adjust the level, then tighten
Damage to the seal when removing the door	Breach of tightness, freezing of the chamber	Warm the seal with a hairdryer or replace it with a new one
Incorrect connection of wires (in models with a display)	The screen does not work, sensor errors	Check the connection diagram using the photo taken before removal
Ignoring the rubber gaskets under the hinges	Vibration, creaks when opening	Install gaskets or lubricate the hinges with silicone

Pay special attention to models with Smart ThinQ system. If, after rehanging, the refrigerator displays an error on the display (for example, Er FF or Er dH), this may mean:

• 🔌 Sensor malfunction door —check its fastening.
• 📡 Failure of communication between modules —reboot the refrigerator (unplug it for 5 minutes).

FAQ: Frequently asked questions about re-hanging the LG door

Is it possible to re-hang the door of an LG refrigerator yourself if it is under warranty?

Technically yes, but Independent intervention may void the warranty. The instructions LG indicate that re-hanging the door should be carried out by a service center. If the refrigerator is new, it is better to contact official specialists - they will do it for free (in most cases).

What to do if, after rehanging, the door of the LG refrigerator does not close tightly?

The reasons may be as follows:

• 🔧 Distortion of the hinges — loosen the bolts and adjust the door according to the level.
• 🚪 Deformation of the seal —try to restore its shape with a hairdryer or replace it.
• 🧲 The magnetic strip of the seal has become loose —check its integrity.

If the problem persists, the hinges may be worn out and require replacement.

Do you need to defrost an LG refrigerator before hanging the door?

If you have a model No Frost, defrosting is not necessary, but it is recommended to unplug the refrigerator. For models with drip system defrosting is necessary to avoid water getting on the electrical contacts during dismantling.

How to hang the door on an LG refrigerator with a water dispenser?

The algorithm is the same, but with additional steps:

1. Turn off the water supply and drain the remaining residue from the hose.
2. Carefully disconnect the hose from the door and move it to the other side.
3. When installing the door, make sure that the hose is not kinked or pinched.

After connecting, check tightness of the connections - if water drips, tighten the clamps.

How much does it cost to rehang the door of an LG refrigerator in a service center?

The cost of the service depends on the region and model:

• 💰 For standard refrigerators (without dispenser) - 1500–2500 rubles.
• 💰 For models with a dispenser or InstaView — 2500–4000 rubles.

In some services the price includes a visit from a specialist, in others it is paid separately (300–500 rubles).

⚠️ Check current prices on the website LG or with official partners - tariffs may change.