How to set up the Polar refrigerator: temperature, modes and functions

Brand refrigerators Polar are popular due to their combination of affordable prices, reliability and modern features. However, even the most advanced equipment requires proper configuration - not only the service life of the device, but also the freshness of the products, as well as the efficiency of energy consumption depend on this. Many owners are faced with questions: what temperature to set in the main chamberhow to turn on the mode Super Coolwhat to do if the freezer freezes and the refrigerator compartment does not cool well?

In this article we will look into all key settings refrigerators Polar —from basic temperature adjustment to activation of special modes (NoFrost, Holiday, Eco). You will also learn how to reset the settings to factory defaults, what the indicators on the control panel mean, and how to avoid common operating mistakes. The instructions are suitable for most brand models, including series CRF, CFD, Polaris and others.

⚠️ Attention: The interface and available functions may vary depending on the model and year of manufacture of the refrigerator. For accurate information, check the user manualenclosed with your device.

1. Basic temperature setting: optimal values ​​for Polar

The first thing to do after connecting the refrigerator is to set the correct temperature in the main chamber and freezer. Not only the safety of products, but also the energy consumption of the device depends on this. In refrigerators Polar adjustment is carried out either by mechanical knobs (in budget models) or by an electronic control panel (in series NoFrost and Inverter).

Recommended temperature values:

  • 🥦 Refrigerator compartment: from +2°C to +5°C. Optimal - +4°C for most products. At lower values, freezing of leafy greens and dairy products is possible.
  • ❄️ Freezer compartment: from -18°C to -24°C. for storing meat and fish, it is better to set -20°C.
  • 🍎 Freshness zone (if any): 0°C —ideal for fruits, vegetables and perishable foods.

How to change the temperature:

  1. On models with mechanical control turn the regulator (usually located inside the refrigerator compartment) to the position from 1 (warmest) to 5-7 (coldest). Polar CRF-105, for example, has 5 positions.
  2. On refrigerators with electronic display (series CFD, Polaris), press the button Temp or Fridge, then select the value with the arrows ↑/↓. Confirm the selection with the button OK.
⚠️ Attention: If after changing the temperature the refrigerator does not cool to the set values within 6-8 hours, check door closure tightness and fan operation (in models with NoFrostmay require defrosting or service). maintenance.
📊 What type of control does your refrigerator have? Polar?
Mechanical (handles)
Electronic (display)
I don’t know
Another brand

2. Operating modes: Super Cool, Holiday, Eco and others

Modern refrigerators Polar are equipped with several special modes that help adapt the operation of the device for different conditions. Let's consider the most useful of them:

Mode Purpose How to turn on When to use
Super Cool Intensive cooling to -2°C in the refrigerator compartment Button Super Cool (hold for 3 seconds) After loading a large amount of warm food
Holiday Economic mode (+10°C in the refrigerator camera) Button Holiday or Eco For long absence (vacation, business trip)
Eco Reduce energy consumption by 10-15% Automatic or button Eco Mode Night time or at high electricity tariffs
Fast Freeze Quick freezing up to -24°C in the freezer Button Fast Freeze (24 hours) When storing fresh products for long-term storage

Important nuances:

  • ⏳ Mode Super Cool works maximum 6 hours, then automatically turns off.
  • 🌿 In Holiday mode, the freezer continues to operate as normal (unless disabled separately).
  • ⚡ Mode Eco can increase the cooling time of food - do not use it if you load warm dishes.

Make sure the door is tightly closed

Check the loading of products (do not overload the chambers)

Turn off the mode after 6-24 hours (if not automatic)

Control the temperature 2-3 hours after activation-->

3. Setting NoFrost: how it works and when defrosting is required

Many models Polar (for example, series CFD-518, CRF-310) are equipped with a system NoFrostthat prevents the formation of frost and ice in freezer compartment. However, this does not mean that the refrigerator does not need to be defrosted at all! Let's figure out how to properly operate such equipment.

Operation principle NoFrost:

  • 🌀 The fan evenly distributes cold air throughout the chamber.
  • 💧 Humidity condenses on a special evaporator, and not on the walls.
  • ❄️ Ice does not form in the freezer, but slight condensation may appear in the refrigerator compartment.

When defrosting is still required:

  1. If the refrigerator has not been disconnected from the network for more than 1 year it is recommended preventive defrosting for cleaning.
  2. If the appearance of an unpleasant odor - defrosting and washing will help eliminate it.
  3. If ice forms in the refrigerator compartment (perhaps the sensor or fan is faulty).

How to defrost NoFrost correctly:

  1. Unplug the refrigerator.
  2. Remove all food and shelves.
  3. Leave the doors open for 4-6 hours (the ice in the freezer should melt on its own).
  4. Wipe the internal surfaces soft rag with soda solution (1 tablespoon of soda per 1 liter of water).
  5. Turn on the refrigerator and wait until it returns to operating mode (1-2 hours).
What happens if you ignore defrosting NoFrost?

Even in systems NoFrost over time, dust and microbes accumulate in the air ducts. This can lead to:

- Deterioration of cooling (due to clogging of the fan)

- The appearance of an unpleasant odor

- Increased energy consumption (up to 15-20%)

- Breakdown of temperature sensors (due to icing of the contacts)

4. Setting up an inverter compressor: energy saving and quiet operation However, proper setup is required for maximum effectiveness. Here's what you need to know:

Models Polar with inverter compressor (e.g. Polaris PIR 330) are characterized by quieter operation and economical energy consumption. However, proper setup is required for maximum effectiveness. Here's what you need to know:

Advantages of an inverter compressor:

  • 🔇 Operates almost silently (noise level ~38 dB).
  • ⚡ Saves up to 30% of electricity compared to conventional compressors.
  • 📉 Maintains a stable temperature without sudden jumps.

How to set it up:

  1. Set the temperature +4°C in the refrigerator and -18°C in the freezer - this is enough for most cases.
  2. Activate the mode Ecoif you want additional savings (but remember that cooling will be slower).
  3. Avoid opening doors frequently - the inverter compressor takes longer to restore temperature after a thermal load.

Typical mistakes:

  • ❌ Setting the temperature too low (for example +2°C) - this increases the load on the compressor and energy consumption by 15-20%.
  • ❌ Using the mode Super Cool unnecessarily - the compressor operates at maximum, which reduces its resource.
  • ❌ Placing the refrigerator next to heat sources (battery, stove) - the inverter compressor will work in enhanced mode.

- Installation level (should be level, without distortions)

- Distance to the wall (minimum 5 cm for circulation air)

- Cleanliness of the rear grille (dust can cause overheating)-->

5. Setting up freshness zones and food distribution

Many refrigerators Polar (for example, CFD-518, CRF-310) are equipped with special zones for storing different types of products. Proper distribution will help maintain freshness longer and avoid spoilage. Here's how to optimally load the chambers:

Refrigerator compartment:

  • 🥬 Top shelves (warmest place, +5..+7°C): dairy products, ready meals, sausages.
  • 🥚 Middle shelves (+3..+5°C): eggs, cheeses, sauces, semi-finished products.
  • 🍎 Lower shelves/drawers (+2..+4°C): meat, fish, perishable foods.
  • 🥕 Boxes for vegetables/fruits (freshness zone, 0..+3°C): greens, vegetables, fruits (except bananas and citrus fruits).

Freezer:

  • 🍗 Upper compartments (-18..-20°C): meat, fish, semi-finished products.
  • 🍦 Lower compartments (-20..-24°C): ice cream, berries, long-term storage.
  • 🧊 Freezer door: ice, quick-frozen foods (for example, grass for tea).

Storage tips:

  • 📦 Do not load food close to the walls - leave a gap of 2-3 cm for air circulation.
  • 🔄 Once every 1-2 weeks, transfer food from the upper shelves to the lower ones (for uniform cooling).
  • 🚫 Do not store in the refrigerator Polar:
    • Onions and garlic (they spoil faster at low temperatures).
    • Bread (dries out, it is better to store in a bread bin).
    • Bananas, pineapples, melons (lose their taste).

6. Resetting to factory settings and troubleshooting

If the refrigerator Polar starts to work incorrectly (does not cool, constantly turns on/off, shows errors on the display), sometimes resetting to factory settings helps. This procedure is also useful before selling or transferring equipment.

How to reset the settings:

  1. Unplug the refrigerator for 10-15 minutes.
  2. Turn it back on and immediately press and hold the button Temp (or Set) for 5-10 seconds.
  3. A flashing message rSt or 0 will appear on the display - this means that the reset was successful.
  4. Adjust the temperature and modes again (see section 1).

Typical malfunctions and methods for their elimination:

Problem Possible cause Solution
The refrigerator does not cool The door is not tightly closed, sensor failure Check the seal, reset the settings
The compressor is constantly running High temperature in the room, a lot of products are loaded Reduce the temperature to chamber, unload the refrigerator
Ice formation in NoFrost Clogged drain hole, fan malfunction Defrost the refrigerator, clean the hole with a cotton swab
The indicator is flashing Alarm The temperature in the chamber is higher than normal Check the door is closed, adjust the temperature again

If the reset does not help, professional repairs may be required. Pay attention to the following signs of serious malfunctions:

  • 🔊 The compressor hums, but does not start.
  • ❄️ A thick layer of ice forms on the back wall of the refrigerator compartment.
  • 💡 The display shows errors E1, E2, E3 (see instructions for the model).
⚠️ Attention: Do not try to repair electronic boards or the compressor yourself - this may lead to loss of warranty or damage to the refrigerator. Contact the service center Polar.

7. Additional functions: display, signals, locking

Refrigerators Polar of the middle and premium segments (for example, CFD-620, PIR-330) are equipped with additional functions that make operation easier. Let's figure out how to set them up:

Display control:

  • 📊 To switch between refrigerator and freezer temperatures, press the button Fridge/Freezer.
  • 🔒 To lock the panel from children, hold the button Lock (or Child Lock) 3 seconds. Unlocking - by pressing again.
  • 🔔 To turn off the sound signal (for example, when the door is open), press and hold the button Alarm Off.

Signals and indicators:

  • 🚨 Door Open — the door is open for more than 1 minute.
  • ❄️ Super Cool — intensive mode is active cooling.
  • ⚡ Eco —economy mode is on.
  • 🔋 Battery (in self-powered models)—low backup battery charge.

Useful features:

  • 💡 Some models have night light — it turns on when the door is opened at night. It can be turned off in the menu Settings → Light.
  • 📅 The function Holiday may have a countdown timer - the refrigerator will automatically return to normal mode after a specified time.
  • 🔄 In refrigerators with Twin Cooling (dual cooling system) you can independently regulate the temperature in each chamber.

8. Care and cleaning: how to extend the life of your refrigerator Polar

Proper care not only maintains hygiene, but also prevents breakdowns. Refrigerators Polar are unpretentious in maintenance, but there are several key rules:

Regular cleaning:

  • 🧽 Internal surfaces: wash once a month with a warm soda solution (1 tablespoon per 1 liter of water). Avoid abrasive products!
  • 🧴 Door seal: wipe with a damp cloth and soapy water (once every 2 months). Check the integrity - cracks lead to loss of cold.
  • 🌀 Ventilation grilles: clean from dust with a vacuum cleaner or soft brush (once every 6 months).

Defrosting (for models without NoFrost):

  1. Carry out defrosting when the ice thickness is more than 5 mm.
  2. Do not use sharp objects to remove ice - this will damage the evaporator.
  3. After defrosting, wipe the chambers dry and turn on the refrigerator 2 hours before loading products.

Odor prevention:

  • 🍋 Once a month, wipe the walls with a solution of lemon juice (1 tablespoon per 1 liter of water).
  • ☕ Place an open pack of soda or a special odor absorber in the refrigerator.
  • 🥩 Store foods with a strong odor (fish, onions, spices) in airtight containers.

What not to do:

  • ❌ Putting hot foods in the refrigerator - this increases the load on the compressor.
  • ❌ Use products with chlorine or acids for washing - they spoil the plastic.
  • ❌ Place the refrigerator next to the stove or radiator - optimal ambient temperature +16..+32°C.

FAQ: Frequently asked questions about setting up refrigerators Polar

🔹 Why does the refrigerator Polar constantly work and does not turn off?

This can be caused by several reasons:

  • High temperature in the room (more than +30°C).
  • Frequent opening of the door or its loose closing.
  • Too many warm products loaded.
  • Temperature sensor failure (diagnostics required).

Try to reduce the temperature in the chamber by 1-2 degrees or activate the mode Eco. If the problem persists, contact the service.

🔹 How to turn off the sound signal when the door is open?

In most models Polar the signal is turned off as follows:

  1. Press and hold the button Alarm Off (or Mute) for 3 seconds.
  2. On some models you need to go to the menu Settings → Sound → Off.

If there is no button, the signal will turn off automatically 1-2 minutes after closing the door.

🔹 Is it possible to move the refrigerator door Polar to the other side?

Yes, in most models the door can be hung. To do this:

  1. Unplug the refrigerator.
  2. Remove the decorative plugs from the hinges.
  3. Unscrew the door fastening bolts (a Phillips screwdriver will be required).
  4. Move the hinges to the other side and secure the door.
  5. Install the plugs on the previous holes.

The instructions for the model have a detailed re-hanging diagram. If it is not there, take a photo of the disassembly process so as not to confuse the parts.

🔹 Why does it form in the freezer? ice? NoFrost does ice form?

Even in systems NoFrost ice can appear for the following reasons:

  • Clogged drain hole (need to be cleaned with a cotton swab).
  • Malfunction of the fan or defrost heater.
  • Frequent opening of the freezer door (moist air gets inside).
  • Failure of the defrost sensor.

Try to defrost the refrigerator for 6-8 hours. If ice appears again, contact the service.

🔹 How to save energy with refrigerator Polar?

Here are several proven methods:

  • Set the temperature +4..+5°C in the refrigerator compartment and -18°C in the freezer.
  • Activate the mode Eco at night.
  • Do not place the refrigerator near heat sources.
  • Regularly defrost and clean the back grille.
  • Check the door seal - even a small gap increases energy consumption by 20%.

Inverter models Polar (for example, PIR-330) already consume 30% less electricity than conventional ones.

📖 Read Also

How many degrees in a Bosch freezer: norm and setting Find out how many degrees there should be in freezer of a Bosch refrigerator. Table of temperature modes How to turn on the freezer in an Electrolux refrigerator: step-by-step instructions Detailed guide to activating the freezer in Electrolux refrigerators with different systems How to set the temperature in a Bosch refrigerator: instructions A complete guide to setting the temperature in Bosch refrigerators. Analysis of models with electronic control and What temperature should be in a Beko refrigerator: setting Detailed instructions for setting the temperature in a Beko refrigerator. Optimal modes for different departments. How to set the temperature in the freezer. Atlant: instructions Detailed instructions for setting the temperature in the freezer compartment of the Atlant refrigerator. Analysis of thermo How many degrees should be in the refrigerator: norm and settings Find out the optimal temperature in the refrigerator to maintain food freshness. data-i="381">❄️ Fridge Advisor