When planning a move or purchasing new household appliances, one of the key parameters is Often overlooked until the moment of delivery is the weight of the unit. This is especially true for high-power models, whose height reaches 2 meters. Two-chamber refrigerator such a height is an impressive device that requires careful logistics preparation.
Users often look for average values, but the weight directly depends on the specific series, the volume of chambers and the type used refrigerant. Improperly assessing the lift's capacity or the physical strength of the movers can result in property damage or injury. Therefore, it is important to understand the technical nuances in advance.
In this article we will take a detailed look at what determines the mass of different modifications of the Atlant brand, provide specific figures for popular series and give recommendations for safe transportation. Accurate data will help you avoid unpleasant surprises on the day of delivery.
Factors influencing the weight of refrigeration equipment
The dimensions of the device are only the visible part of the iceberg. Many internal components and design features affect the final weight in kilograms. First of all, this is the case material and wall thickness. A thicker layer thermal insulation not only holds the cold better, but also adds significant kilograms to the total mass.
The second important factor is the compressor. Older models often had heavy motors, while modern inverter systems may be lighter but require more complex electronics, which also add weight. In addition, the number of cooling circuits plays a role: No Frost or Full No Frost systems include additional fans, heaters and air ducts.
Don't forget about the refrigerant. Although freon itself is lightweight, systems designed for certain types of gases may have different thicknesses of the evaporator tubes. Also, the weight depends on the configuration: the presence of a water dispenser, an ice maker or glass shelves instead of lattice significantly changes the balance.
⚠️ Attention: When calculating the load on the floor, take into account not only the weight of the empty refrigerator, but also the mass of food that will be stored in it. A full load can add another 30-50 kg to the static load on the floors.
Weight review for the popular Atlant series
The Belarusian manufacturer produces equipment in several main lines, and each of them has its own weight characteristics. The 40 and 45 series models, which are often found in apartments, are typically lighter than their taller cousins. Their weight, as a rule, varies between 55-60 kg.
Series 50, which has become widespread due to its optimal price-quality ratio, is already heavier. The two-chamber models of this line are about 2 meters high and weigh on average from 62 to 66 kg. It uses a more massive compressor and an increased volume of the freezer.
The heaviest representatives are models of the 60 and 70 series. These units are positioned as premium or large-sized solutions for large families. The weight of such refrigerators can reach 70-75 kg and even higher if we are talking about modifications with the system No Frost in both chambers.
It is important to understand that even within the same series the weight may differ. For example, a model with a clear (silver) body coating may be slightly heavier than its counterpart in white enamel due to differences in the technology for applying the finishing layer.
Table of characteristics and weights of models
For ease of comparison, we have systematized data on popular two-meter models. Please note that the values are for devices without packaging. The transport mass, including polystyrene foam, cardboard and a wooden pallet, will be approximately 5-8 kg larger.
| Series | Model (example) | Height, cm | Total volume, l | Net weight, kg |
|---|---|---|---|---|
| Series 40 | XM-4008 | 205 | 340 | 58 |
| Series 50 | XM-5008 | 205 | 345 | 64 |
| Series 60 | XM-6021 | 205 | 360 | 68 |
| Series 70 | XM-7003 | 200 | 380 | 72 |
As can be seen from the table, the difference between the lightest and The heaviest model is more than 10 kg. This is an essential parameter if you have to lower equipment down stairs without a freight elevator. Heavy models require the participation of at least two people for safe movement.
It is also worth considering that the weight declared by the manufacturer is a permissible deviation within 5%. The actual weight of a particular instance may differ slightly from the passport data, up or down.
Nuances of transportation and movement
Transporting a two-meter refrigerator is not just moving a box from point A to point B. It is a complex process that requires compliance with safety precautions. The main danger is a shift in the center of gravity. A tall and narrow body becomes unstable when tilted.
If you plan to transport equipment in a personal car, make sure that the interior or trunk can withstand the load. When installed in a rear seat, the pressure at one point may exceed the permissible limits for the upholstery and seat frame. It is better to use a flat trunk floor or the body of a cargo taxi.
- 🚚 Always secure the refrigerator with straps so that it does not move when braking or turning.
- 📏 Measure the doorways in advance: a two-meter unit may not fit through a narrow corridor when disassembled.
- 🧊 It is strictly forbidden to transport the refrigerator lying on its side for less than 15-20 minutes without subsequent standing.
When moving up the stairs, you must ensure that one of the carriers is always at the bottom and controls stability, and the second holds the body from above. Jerks and impacts on steps can damage the insulating circuit or tubes.
☑️ Preparing to move
Installation features after delivery
After the heavy load has been delivered to its destination, the installation phase begins. Here it is important to correctly level the equipment. Incorrect installation will lead to increased noise, vibration and even failure of the compressor.
Use the adjustable feet located on the front bottom of the housing. By rotating them, make sure that the refrigerator is stable and does not wobble when lightly pressing on the corner. The door should open smoothly and close on its own with a slight push thanks to a slight tilt back.
⚠️ Attention: Do not try to push the refrigerator filled with food to the wall with one hand. This may damage the floor or break the adjustable feet. Move the empty housing.
It is important to provide a gap between the rear wall of the unit and the wall of the room. To effectively remove heat from the condenser, a distance of at least 5-7 cm is required. Built-in models require special ventilation in a niche.
Why can’t you turn it on right away?
If the refrigerator was transported lying down or simply shaken on the way, oil from the compressor could get into the cooling circuit. Switching on will immediately lead to water hammer and breakdown of the compressor. It is necessary to let the equipment stand vertically for 2 to 4 hours (or better yet, a day) for the oil to drain.
The influence of the type of defrosting on weight
The type of defrosting system is one of the hidden factors that influence the weight. The classic drip system (Direct Cool) in the freezer compartment and manual defrosting in the main compartment make the design simpler and lighter. Such models have fewer plastic elements and do not have a complex system of air channels.
Models with the system No Frost (or Full No Frost) are much heavier. The presence of an evaporator in a special box, a fan, a defrosting element and a condensate collection system adds several kilograms to the weight. In addition, these refrigerators often have thicker walls to compensate for fan operation and prevent condensation from forming outside.
By purchasing a model with full No Frost, you get convenience (no need to defrost manually), but sacrifice useful volume (due to air ducts) and add weight. For older people or when moving frequently, this can be a decisive factor.
It is worth noting that Atlant models with No Frost often use more powerful compressors, which also have increased weight compared to low-power counterparts for simple cooling systems.
Frequently asked questions and technical details
Users We are often concerned about issues related to the maintenance and relocation of heavy equipment. For example, is it possible to remove the door to reduce weight when climbing to the floor. Theoretically, this is possible, but in practice it is difficult for Atlant models.
The doors are mounted on powerful hinges, and their dismantling requires special tools and skills. Moreover, removing the door does not mean reducing the weight of the case significantly, since the bulk of the weight is concentrated in the compressor, the metal of the case and thermal insulation. The removed door weighs 10-15 kg, which does not solve the problem radically.
- 🔧 To dismantle the door, you will need open-end wrenches and the help of a second person to fix the panel.
- ⚖️ Removing the door will make it easier to carry only in narrow openings, but will not reduce the load on loaders when climbing stairs.
- 🛡️ When removing the door, there is a high risk of damaging the seal or scratching the coating if you are not careful.
If you are planning to install a built-in refrigerator, the weight of the facade panel should also be taken into account when calculating the load on the furniture box guides. A panel made of MDF or solid wood can weigh from 10 to 20 kg.
Is it possible to transport the Atlas refrigerator lying down?
Transportation in a horizontal position is not recommended by the manufacturer, but is possible over short distances if precautions are taken. The device should only lie on its side (not on the back or on the door!), preferably on where the door hinges are located. After transportation, be sure to let the equipment stand upright for at least 4 hours before turning it on.
Why can an Atlant 2-meter refrigerator be lighter than its analogues?
Atlant models often use a classic cooling system with one compressor and manual defrosting of the freezer, which makes them lighter than their European counterparts with Full No Frost and two compressors. Steel of a certain thickness is also used, optimized to reduce weight without losing strength.
Can an old elevator withstand a two-chamber refrigerator?
The standard load capacity of a passenger elevator is 350-400 kg (5-6 people). One refrigerator weighing 70 kg will easily fit into these standards. Problems may arise only with the dimensions: a two-meter case may not fit into the cabin diagonally if the elevator is very narrow (less than 110 cm in depth).