How to properly turn on the refrigerator in a Vatten cooler: instructions for all models

Coolers Vatten with the function of cooling water and food are becoming increasingly popular in offices, apartments and catering establishments. However, many users encounter difficulties when turning it on for the first time refrigerator mode —especially when it comes to models with hybrid systems (Vatten VWC-100H, Vatten Cool Pro or Vatten EcoChill). Unlike classic refrigerators, here you need not only to connect the device to the network, but also to correctly activate the cooling through the control panel or mobile application.

In this article we will look at step-by-step algorithm for turning on the refrigerator compartment in coolers Vatten, we will pay attention to typical errors (for example, when the cooler hums, but does not cool), and we will explain how to check the performance of the system. You will also find a table of compatibility of models with cooling functions and tips on optimal temperature settings for different types of products.

If your cooler Vatten is equipped with a display, the process of turning on the refrigerator will take no more than 5 minutes. The main thing is not to skip the sensor calibration step, which automatically starts the first time you connect. For models without a screen (for example Vatten BasicCool), you will need to use a combination of buttons - we will talk about this separately.

1. Preparing the Vatten cooler for the first use

Before activating the refrigeration mode, make sure that the device is installed in accordance with all the rules. Failure to comply with installation conditions This may lead to malfunctions of the compressor or improper distribution of cold.

Here are the key ones points to check:

• 🔌 Socket: the cooler must be connected to a grounded network (especially important for models with an inverter compressor). Use a surge protector if your electrical network experiences power surges.
• 🌡️ Room temperature: the optimal range is from +16°C to +32°C. At lower or higher values, the cooler may operate unstably.
• 🚫 Gaps for ventilation: leave at least 10 cm of free space on all sides of the device, especially at the back where the radiator is located.
• 💧 Level: use a building level to level cooler An uneven surface leads to incorrect operation of the temperature sensors.

If you have just delivered the cooler from the store let it stand in a vertical position for at least 4-6 hours before turning it on. This is necessary to stabilize the refrigerant in the system. Ignoring this rule can lead to water hammer of the compressor.

⚠️ Attention: Models Vatten with the function SuperCool (fast cooling) require preliminary configuration via mobile phone application. Without this, the modes may not work correctly.

2. Step-by-step instructions: how to turn on a refrigerator on a Vatten cooler

The switching algorithm depends on the type of control panel of your cooler. Below we will look at the three most common options: touch display, mechanical buttons and control via an application.

For models with a display (for example, Vatten VWC-200D):

1. Press the button Power on the front panel to turn on the cooler.
2. Wait for the system to boot (the logo will appear on the screen Vatten).
3. Go to the menu Settings → Cooling Mode.
4. Select mode Fridge (refrigerator) and set the target temperature (recommended value - +4°C).
5. Confirm the selection with the button OK. The compressor will start in 1-2 minutes.

For models with mechanical buttons (for example, Vatten BasicCool):

1. Hold the button Cool (usually indicated by a snowflake) for 3 seconds until you hear a sound signal.
2. Short press the same button to select the mode Fridge (flashing indicator FR).
3. Press Temp +/–to set the temperature. The adjustment range is from +2°C to +8°C.
4. Wait for a double signal - this means that the settings are saved.

For models with Wi-Fi support (for example, Vatten SmartChill), first connect the cooler to the application Vatten Connect via Bluetooth, and then activate the refrigeration mode in the section Climate Control.

Make sure the cooler is installed level

Check the connection to a grounded socket

Let the device sit for 4-6 hours after transportation

Select Fridge mode in the menu or through the buttons

Set the temperature to +4°C (optimal for most products)-->

3. Table: compatibility of Vatten models with the refrigerator function

Not all coolers Vatten support the product cooling mode The table below shows popular models and their capabilities:

If your model is not in the table, check the technical data sheet or the sticker on the back panel of the cooler Designation FR or Fridge Mode confirms support for the refrigeration mode.

⚠️ Attention: In models Vatten with a hybrid cooling system (EcoChill, SmartChill), when you first turn on the refrigerator, you may need to update the firmware If appears on the display. error E03, connect the cooler to Wi-Fi and start the update through the menu System → Update.

4. Typical errors and their solutions

Even when the refrigeration mode is turned on correctly, users often encounter problems. Let's consider the most common situations and ways to resolve them.

The cooler hums, but does not cool:

• 🔍 Check that the food compartment door is closed. Even a small gap can lead to cold leakage.
• ❄️ Make sure that the room temperature does not exceed +32°C If the compressor overheats, it will automatically cool. turns off.
• ⚡ Check the voltage in the outlet (should be 220-240 V). Use a stabilizer if there are surges in your network.

An error flashes on the display E01 or E02:

• 🔄 Turn off the cooler. from the outlet for 10 minutes, then turn it on again. This will reset the sensor error.
• 🧊 If the error repeats, check whether the condensate is frozen in the drainage system (relevant for models with NoFrost).
• 📞 For an error E02 (compressor malfunction), contact the service center - independent repairs can aggravate the problem.

The refrigerator works, but the temperature does not drop below +8°C:

• 🌡️ Check whether the compartment is overloaded with products. Air circulation should be free.
• 🔄 Set the mode SuperCool for 2 hours for forced cooling.
• 🛠️ Clean the rear grille of the cooler from dust - a clogged radiator reduces the cooling efficiency.

What to do if the Vatten cooler does not respond to buttons?

If the control panel does not respond, try:

1. Disconnect the cooler from the network for 1 minute, then turn it on again.

2. Check if one of the buttons is stuck (relevant for mechanical panels).

3. Reset the settings to factory defaults by holding the button Reset (usually located on the rear panel) for 10 seconds.

If the problem persists, this may indicate a faulty control board - diagnostics will be required at a service center.

5. Optimal temperature settings for different products

The refrigerator mode in the cooler Vatten allows you to store not only drinks, but also perishable foods. However, for maximum shelf life, it is important to set the temperature correctly.

Recommended values:

• 🥛 Dairy products: +2°C...+4°C (for example, yoghurts, sour cream, cottage cheese).
• 🍎 Fruits and vegetables: +4°C...+6°C (except for bananas and citrus fruits - they are best stored at +8°C).
• 🥩 Meat and fish: 0°C...+2°C (in sealed packaging).
• 🧀 Cheeses: +4°C…+7°C (depending on the type: hard - closer to +4°C, soft - closer to +7°C).
• 🥤 Drinks: +3°C...+5°C (optimal for sparkling water, juices, beer).

In models Vatten with a freshness zone (FreshZone), you can set different temperatures for the top and bottom shelves. For example, in Vatten SmartChill the bottom shelf is cooled to +1°C (for meat), and the top shelf is cooled to +5°C (for vegetables).

Energy saving tip:

If you store only drinks in the cooler, set the temperature to +6°C...+8°C. This will reduce the load on the compressor and reduce energy consumption by 15–20%.

6. Caring for the refrigeration compartment of a Vatten cooler

Regular maintenance extends the life of the cooler and prevents the appearance of unpleasant odors. Here are the basic rules of care:

Weekly:

• 🧼 Wipe the internal surfaces of the compartment with a weak solution of baking soda (1 tablespoon per 1 liter of water).
• 🗑️ Remove expired products and check for leaks packages.
• 💨 Ventilate the compartment for 5–10 minutes (disconnecting the cooler from the mains).

Monthly:

• ❄️ If your model is not equipped with a system NoFrost, defrost the compartment when ice forms more than 5 mm thick.
• 🔧 Check the door sealing rubber - it should fit snugly without gaps.
• 🧹 Clean the rear grille of dust using a vacuum cleaner or soft brush.

Every 6 months:

• 🔄 Replace the carbon filter (if provided in the model) to eliminate odors.
• 🛠️ Check the operation of the drainage hole - if clogged, condensation will accumulate at the bottom of the compartment.

For models with the function AutoClean (for example, Vatten EcoChill) it is enough to run automatic cleaning once a month through the menu Maintenance → AutoClean.

⚠️ Attention: Never use abrasive detergents or hard sponges to clean internal surfaces. This may damage the antibacterial coating used on the compartments in the coolers Vatten.

7. Frequently asked questions about the refrigeration mode in Vatten coolers

In this section we have collected answers to the most popular questions from users.

Can medications that require a temperature of +2°C...+8°C be stored in a Vatten cooler?

Yes, but with reservations. Most models Vatten support a range of +2°C...+8°C, however, temperature stability is critical for medications. Before use:

1. Check the cooler with a thermometer within 24 hours - temperature fluctuations should not exceed ±1°C.
2. Use the mode StableCool (if available in your model) to minimize differences.
3. Store medications in an airtight container on the middle shelf, where the temperature is most stable.

For critical medications (for example, insulin), it is better to use specialized medical refrigerators.

Why does the Vatten cooler make a lot of noise when the refrigerator is running?

Compressor noise is normal, but if it becomes louder than usual, it is possible the following reasons:

• 🏠 The cooler is installed on an uneven surface - vibration increases the noise. Use rubber pads.
• 🧊 Condensate in the drainage system is frozen - defrosting is required.
• 🔧 Compressor wear (relevant for models older than 5 years). In this case, the noise will increase gradually.

If the noise is accompanied by an error on the display, contact service.

How long does it take to cool the compartment to +4°C from room temperature?

The time depends on the model and the load on the compartment:

• 🔹 Empty compartment: 30–60 minutes.
• 🔹 50% filled: 1.5–2 hours.
• 🔹 Fully loaded: up to 3–4 hours.

To speed up the process, use mode SuperCool (if available).

Is it possible to turn off the Vatten cooler at night if the refrigeration mode is not needed?

Technically yes, but this is not recommended for two reasons:

1. 🔄 Frequent switching on/off will shorten the service life compressor.
2. 🌡️ When turned on again, the cooler will require more energy to cool to the set temperature.

The optimal solution is to switch the cooler to mode Eco (if it is supported by your model). This will reduce energy consumption by 30–40% without completely shutting down.

How to reset the refrigerator to factory settings?

The reset method depends on the model:

• 📱 For coolers with a display: go to Settings → System → Factory Reset.
• 🔘 For models with buttons: hold Cool + Temp + for 10 seconds.
• 🌐 For "smart" coolers: reset is available in the mobile application Vatten Connect in the section Device → Reset.

After resetting all settings (including temperature and timers) will be deleted.