A modern refrigerator Beko is a complex electronic device that requires proper initial setup for correct operation. After purchase or interruption in use, it is necessary not only to turn on the device, but also to correctly set the cooling parameters so that the products remain fresh for as long as possible. Many users make the mistake of ignoring the stabilization period, which can lead to compressor failure.
Owners often have to face the question of how to set temperature conditionsso that vegetables do not freeze in the refrigerator compartment, and meat quickly freezes in the freezer. The intuitive interface of control panels is not always obvious at first glance, especially on models with electronic controls and display. In this article we will analyze all the nuances of setting up various series of household appliances of the Turkish brand.
The first thing you need to do after delivering the unit home is to let it settle. This is critical if transport was carried out in a horizontal position. The oil must drain into the compressor crankcase, otherwise water hammer may occur upon first start-up. Only after this you can begin connecting and setting up basic functions.
⚠️ Attention: If the refrigerator was transported lying down, let it stand upright for at least 4-6 hours before plugging it in. Ignoring this rule may lead to failure of the compressor, which is not a warranty case.
Primary preparation and setting the temperature conditions
Setting up any refrigerator Beko begins with choosing the correct location and alignment of the case. The device must be positioned strictly horizontally so that the doors close tightly under their own weight. If the floor is uneven, use the adjustable feet at the bottom of the front panel. After installing the device in place and connecting to the power supply, the indicators on the display will light up.
For models with mechanical control, there is a thermostat inside the refrigerator compartment - a round knob with numbers from 1 to 5 or from Min to Max. Everything here is extremely simple: the higher the number, the lower the temperature inside. The optimal value for everyday work is position “3” or “4”. You should not immediately turn the knob to the maximum, as this will force the compressor to work without interruption, which will lead to the formation of ice on the back wall.
In more modern models with electronic control, the setting is made through a panel on the door or inside the chamber. You need to press the button Freezer or Fridgeto select the adjustment zone, and then use the arrow buttons or press again to set the desired value. The recommended temperature for the refrigerator compartment is +4°C, and for the freezer compartment - -18°C.
It is worth noting that the temperature inside the chamber may be unevenly distributed during the first hours of operation. This is normal for No Frost i Low Frostsystems. The circulation of cold air takes time to establish a stable flow. Do not fill the shelves with products immediately, let the empty volume cool evenly.
Control of fast freezing and cooling functions
Refrigerators Beko equipped with useful functions for emergency situations, such as Super Freeze (Super Freeze) and Super Cool (Super cooling). These modes allow you to quickly lower the temperature in the freezer or refrigerator compartment, respectively. This is especially true when you have brought a large amount of fresh food and want to retain maximum vitamins and moisture in them.
To activate the quick freezing function, press the button Freezer or a special button with a picture of a snowflake. The corresponding indicator will light up on the display. In this mode, the compressor runs continuously, ignoring standard shutdown cycles. The temperature in the freezer drops to -24°C...-26°C. It is important not to keep this function turned on constantly, as this leads to excessive power consumption and wear of parts.
- ❄️ Mode Super Freeze automatically turns off after a certain time (usually 24-50 hours depending on the model) or manually by pressing the button again.
- 🥦 The function Super Cool is useful before a large purchase of products; it quickly cools a new load without affecting existing stocks.
- ⏱️ In some models, the countdown timer shows how much time is left before exiting the accelerated operation mode.
The use of these functions requires an understanding of heat transfer processes. If you put a large amount of food at room temperature in the freezer, switching on Super Freeze 3-4 hours before loading will prepare the necessary cold supply. This will prevent partial defrosting of existing stocks due to heat gain from new products.
⚠️ Attention: Do not leave the “Super Freeze” mode on for more than 3 days unless necessary. Long-term operation of the compressor at its maximum capacity can shorten the service life of the refrigeration unit.
Setting the freshness zone and zero chamber
The setting of special storage zones, which are present in many models, deserves special attention. Beko. The so-called “zero zone” or Zero Zone is designed for storing meat, fish and dairy products at temperatures close to 0°C, but without freezing. In such conditions, bacteria multiply more slowly, and products remain fresh up to three times longer than in a conventional compartment.
In some modifications, the temperature in this zone is regulated separately using a special slider or electronic panel. If you plan to store perishable food there, make sure the cold air damper is fully open. To store vegetables and fruits, on the contrary, it is better to limit the air flow so that they do not dry out or freeze.
Technology Active Fresh Blue Light in models Beko imitates natural sunlight, supporting the process of photosynthesis in vegetables and fruits even after harvesting. For this function to work correctly, you do not need to configure anything - it is activated automatically when the camera is illuminated. However, it is important not to clutter the lighting area so that the light falls on the products.
What is the BioFresh zone and its analogue in Beko?
This is a special compartment with a cooling system, where the temperature is kept strictly around 0°C. Unlike a conventional freezer, food here does not freeze into ice, but also does not spoil for several weeks.
Proper distribution of food among storage areas is the key to efficient operation of the refrigerator. It is better to place meat and fish in the coldest zone (usually the top shelf or a special drawer), and vegetables and fruits in the lower pull-out containers, where the humidity is higher and the temperature is slightly above zero.
Humidity adjustment and No Frost system
System No Frost (or Low Frost in budget models) eliminates the need for manual defrosting. However, it requires correct humidity settings in individual zones. In refrigerators Beko special dampers on the drawers for vegetables and fruits are responsible for this. By moving the slider, you regulate the flow of dry, cold air.
If you are storing foods with a high water content (greens, lettuce, berries), the damper should be closed or set to the “High Humidity” position. This will limit dry air from the freezer and prevent wilting. For products that emit moisture or require dryness (cheeses, sausages, mushrooms), it is better to open the damper to ensure circulation.
| Product type | Recommended zone | Humidity damper position | Temperature mode |
|---|---|---|---|
| Fresh meat, fish | Zero zone / Top shelf | Does not matter | 0°C... +2°C |
| Vegetables, fruits, herbs | Bottom drawers | Closed (High Humidity) | +4°C... +6°C |
| Dairy Products | Middle Shelves / Door | Standard | +2°C... +4°C |
| Ready Meals | Medium shelves | Standard | +4°C |
Incorrect humidity settings can lead to vegetables rotting from condensation or, conversely, drying out in a couple of days. Monitor the condition of the products and adjust the position of the regulators on the boxes. In models with NeoFrost the system itself controls the humidity balance, but the presence of regulators on the drawers still requires manual adjustment by the user.
Setting up smart functions and vacation mode
Modern refrigerators Beko are often equipped with the “Vacation” function (Holiday Mode). This mode is necessary when you leave for a long time and leave the refrigerator empty. It allows you to turn off the operation of the refrigerator compartment, preventing the appearance of odors and mold, while the freezer continues to operate as normal, preserving stocks of frozen food.
To activate the vacation mode, you must press and hold the corresponding button (often indicated by a palm tree or an inscription Holiday) for 3 seconds. The indicator will light up on the display and the temperature in the refrigerator compartment will rise to +14°C...+15°C. This is enough to prevent bacteria from growing inside, but the compressor will turn on extremely rarely, saving energy.
☑️ Check before holiday mode
Some models support control via Wi-Fi and application HomeWhiz. This allows you to adjust the temperature, activate super freeze or receive open door notifications directly from your smartphone. To set up the connection, follow the instructions on the refrigerator screen: usually you need to hold down the Wi-Fi button and connect the device to your home network.
⚠️ Attention: Before turning on the “Vacation” mode, be sure to remove all perishable foods from the refrigerator compartment. At a temperature of +15°C, milk and meat will spoil in a few hours.
Diagnostics and resetting settings to factory settings
During operation, it may be necessary to reset all user settings and return the refrigerator Beko to factory settings. This often helps resolve software glitches where the display goes blank, all lights flash, or the device stops responding to commands. The standard reset procedure may differ depending on the series.
Most often, to reset, you need to simultaneously press two buttons, for example, Freezer and Super Freeze, and hold them for 5-10 seconds until a sound signal or the display flashes. In models without a display, a reset can be done by disconnecting the device from the network for 10-15 minutes. After switching on, the settings will return to standard values (usually +4°C and -18°C).
If error codes appear on the display (for example, E01, E02), this is a signal of a malfunction of the sensors or defrost system. In such cases, simple reconfiguration will not help - diagnostics are required. However, sometimes the error is temporary and disappears after a full cycle of defrosting and resetting the settings.
Remember that electronics are sensitive to power surges. If your network experiences frequent interruptions, it is recommended to use a stabilizer. This will protect the control unit and save your settings from corruption.
Why does the Beko refrigerator make a lot of noise after setting?
The noise can be caused by several reasons: incorrect installation (legs are not aligned), touching the back wall of the cabinet, or the compressor operating in super-freeze mode. Also, a new refrigerator may make a louder noise during the break-in period (the first 2-3 weeks). If the noise is similar to gurgling, this is normal, the refrigerant is circulating.
How often do you need to defrost a refrigerator with No Frost?
The No Frost system assumes the absence of ice, but sanitary defrosting and washing are recommended 1-2 times a year. This is necessary to remove bacteria, mold and odors that are not removed by filters. Before washing, be sure to unplug the appliance.
What to do if food freezes in the Beko refrigerator?
Check the position of the thermostat - it may be set to maximum. Make sure that the food does not touch the back wall (where cold air escapes). Check the door seal for leaks. If the problem is not solved, the temperature sensor or air damper may be faulty.
Is it possible to transport a Beko refrigerator lying down?
Transporting lying down is not recommended, but is possible if you take precautions. You only need to transport it on one of the sides (usually the one where there are no condenser tubes, it is better to check the instructions for the specific model). After installation, be sure to let the refrigerator stand upright for at least 4-6 hours before turning it on.