Hanging the refrigerator door Biryusa is a task that every owner faces sooner or later. The reasons can be different: moving to a new kitchen, changing the layout, inconvenient opening due to nearby furniture, or simply a desire to refresh the interior. Fortunately, most models Biryusa (from classic Biryusa-18 to modern Biryusa-220 with a display) support this option. But before you take up the screwdriver, it’s worth understanding the nuances.
In this article you you will find step-by-step instructions taking into account the characteristics of different series, a list of necessary tools, as well as typical mistakesthat can lead to damage to the hinge or seal. We will figure out how to cope with the task without the help of a wizard, even if you have a model with electronic control or system No Frost. And at the end - answers to the most frequently asked questions on the topic.
⚠️ Important: The design of hinges and fastenings may vary depending on the year of manufacture of the refrigerator. If your model is older than 2010, check the completeness of the fasteners in the product passport or on the official website Biryusa.
1. Preparation: tools and conditions
Before you start work, make sure that you have everything you need. Most tools can be found in the home arsenal, but some models Biryusa (for example, with touch display) may require special keys.
Here is the minimum set:
- ✅ Phillips screwdriver (size PH2 or PH3 - depends on the model)
- ✅ Flat screwdriver (for prying up decorative plugs)
- ✅ 10 or 8 mm wrench (for bolts loops). data-i="85">Biryusa-26
- ✅ Hexagon 5 mm (for some models Biryusa-22 And Biryusa-26)
- ✅ Painting tape (to secure the door during operation)
- ✅ Level (to check evenness after installation)
Also prepare your workspace:
- 📏 Make room around the refrigerator - you will need to fully open the door and maneuver it.
- 🧊 Unplug the refrigerator and defrost (if the model is not No Frost).
- 🧴 Remove all magnets, stickers and shelves from the door - they can interfere or be damaged.
⚠️ Attention: If your refrigerator is Biryusa s display or electronic control unit, before starting work, take a photo of the location of the wires under the hinge cover. In some models (for example, Biryusa-220C), you need to reconnect the contacts when rehanging!
2. Removing the old door: step-by-step algorithm
We start with dismantling the old door. This stage is the most important - if you remove the hinges incorrectly, you can damage the fasteners or seal.
Step 1. Remove the decorative plugs. They hide the hinge bolts and are usually secured with latches. Pry them off from the side, starting from the bottom. Biryusa-18 and Biryusa-22 the plugs are plastic, in newer ones (for example, Biryusa-26K) - metal.
Step 2. Unscrew the bolts of the upper hinge. There are usually 2-3 of them. Hold the door so that it does not fall! In some models, the bolts may be hidden under the decorative trim - this also needs to be removed.
Step 3. Carefully remove the door from the lower hinge. To do this, slightly lift it up (1-2 cm) and pull it towards you. If the door “jams”, check that all the bolts are unscrewed.
⚠️ Attention: In refrigerators Biryusa with system No Frost there may be additional wires inside the door to heat the seal. Do not pull the door sharply - first disconnect the connectors!
All products and shelves have been removed from the door
The refrigerator has been disconnected from the network
The location of the wires has been photographed (if there is a display)
A place has been prepared for laying the removed door (soft surface)-->
3. Transferring the hinges to the other side
After removing the door, you need to move the hinges to the opposite side:
1. holes. On the body of the refrigerator Biryusa usually there are already symmetrical holes for hinges on the other side (they are closed with plugs). If they are not there, use the template from the old side, attaching the hinge to the new place and marking it with a pencil.
2. Fastening the hinges. Tighten the bolts crosswiseto avoid distortion. The tightening torque is moderate (do not overtighten so as not to break the thread!). In models with gas shock absorbers (for example, Biryusa-220KSh) the lower hinge is fixed first, then the upper one.
3. Checking the level. After installing the hinges, attach the door and check whether it is level. If there is a misalignment, adjust the position. loops.
| Refrigerator model | Hinge type | Weighing features |
|---|---|---|
| Biryusa-18, Biryusa-22 | Classic mechanical | Simple design, plastic plugs. Bolts for Phillips screwdriver. |
| Biryusa-26K, Biryusa-28 | Reinforced with shock absorbers | A hexagon is required for the lower hinge. Check the smooth operation after installation. |
| Biryusa-220S, Biryusa-240 | Electronic (with wires) | Required reconnect the display contacts. The kit may include an adapter. |
🔧 In models Biryusa 2020 and newer, the lower hinge may have a hidden lock - it must be released with a screwdriver before removing the door.
4. Installing the door in a new place
Now all that remains is to fasten the door on the new hinges. This process seems simple, but there are some tricks here.
Step 1. Place the door on the bottom hinge. To do this, lift it at an angle of 15-20° and carefully lower it onto the hinge pin. stop.
Step 2. Secure the top hinge. Start by pre-fixing the bolts, then tighten them completely. On models with display connect the wires first, then secure the hinge cover.
Step 3. Check the tightness of the fit. seal. Close the door and run your hand around the perimeter - there should be no gaps. If the seal “bulges out,” adjust the position of the hinges.
⚠️ Attention: After rehanging, the door may close tighter than before. This is normal - the seal will take a new shape in 1-2 days. If after a week the problem remains, check adjusting the hinges or the condition of the seal.
5. Now you need to adjust the door so that it closes smoothly and tightly.
Outweighing is only half the battle. Now you need to adjust the door so that it closes smoothly and tightly.
1. Check the tightness. data-i="181">If the door touches the body from below or above, loosen the hinge bolts and slightly move it in the desired direction. In models Insert a sheet of paper between the seal and the refrigerator body. If the sheet falls out or is easily pulled out, the seal does not fit.
2. Vertical adjustment. If the door touches the body from below or above, loosen the hinge bolts and move it slightly in the desired direction. In models Biryusa with gas shock absorbers adjustment may require a special key.
3. with display). After re-hanging, turn on the refrigerator and make sure that the display is working and the door closing sensors are activated. If the “door open” indicator is constantly on, check the contacts in the hinge.
📊 Leakage test: After adjustment, leave the refrigerator running for 1-2 hours. Then check if frost has appeared on the back wall (in models without No Frost). If so, the seal allows air to pass through.
6. Common mistakes and how to avoid them
Even with careful work, you can make mistakes that will lead to breakdown:
- ❌ Tightening the hinge bolts. This leads to failure. to deformation of the fasteners or breakage of the thread. Tighten the bolts with moderate force.
- ❌ Ignoring the wires in models with display. If you do not reconnect the contacts, the door will not lock, and the display may fail.
- ❌ Wrong marking of holes. If the hinges are installed asymmetrically, the door will be skewed. Use a level!
- ❌ Damage to the seal. When removing the door, do not pull the seal - it may tear or deform.
🔧 How to correct the misalignment? If the door hangs crookedly, loosen all the hinge bolts, level it and tighten it again. In extreme cases, you can use adjusting washers (they are included with some models. Biryusa).
💡 Advice: If, after rehanging, the refrigerator begins to freeze worse, check if the temperature sensor has moved (in models with electronic control). It can be attached to the door or near the hinges.
What to do if the hinge bolt does it scroll?
If the thread in the refrigerator body is broken, you can use threaded insert (foot) or a bolt of a larger diameter (if the hole allows). As a last resort, contact the service center Biryusa to restore the thread.
7. Features for models with No Frost and display
Refrigerators Biryusa with system No Frost or electronic control require additional actions when rehanging.
For models with No Frost:
- 🔌 Disconnect the seal heating wires (if any) before removing the door.
- ❄️ After installation, check that has the air circulation in the freezer been disrupted?
For models with a display (Biryusa-220C, Biryusa-240):
- 📱 Take a photo of the location of the wires and connectors in front shutdown.
- 🔧 In some models, it is necessary to move the control unit to the other side - for this, additional fasteners are included.
⚠️ Attention: In refrigerators Biryusa with touch display after reversing, you may need to reset the settings. To do this, press and hold the button Super Cool (or Super Freeze) for 5 seconds.
8. When is it better to call a specialist?
Despite the fact that hanging the door Biryusa is a feasible task for most users, there are cases when it is better to turn to professionals:
- 🔧 If the hinge bolts are torn off, and the threads cannot be restored on your own.
- 💻 If after re-hanging the display or electronic control unit does not work.
- ❄️ If the refrigerator has stopped freezing and the seal is in order.
- 🔌 If a short occurs when reconnecting the wires short circuit.
The cost of re-hanging the door at a service center Biryusa is from 1500 to 3000 rubles (depending on the model and region). This is cheaper than repairing after an unsuccessful attempt on your own.
📞 How to find an official service? On the website Biryusa there is an interactive map with the addresses of authorized workshops. Before your visit, check whether they work with your model - some new series require special tools.
FAQ: Answers to frequently asked questions
Is it possible to re-hang the door on the refrigerator Biryusa-18 without an assistant?
Technically, yes, but it’s inconvenient. The door weighs 10–15 kg, and it’s difficult to hold it with one hand while tightening the bolts with the other, it’s better to invite an assistant or secure the door to the body with masking tape.
After re-hanging, the door closes with difficulty. What to do?
There may be two reasons:
- The seal has not yet taken a new shape - wait 1-2 days.
- The door is skewed - loosen the hinge bolts and adjust its position according level.
If the problem persists, check whether the seal was deformed during removal.
Do you need to defrost the refrigerator before re-hanging?
It is mandatory if you have a model without No FrostOtherwise, condensation may get on it. electronics or fastenings. No Frost it is enough to unplug the refrigerator for 30 minutes.
Is it possible to re-hang only the top door (in two-chamber models)?
Yes, but the process will be a little more complicated:
- Remove the top one. door.
- Move the hinges.
- Adjust the position so that it does not interfere with the lower door.
In some models Biryusa (for example, Biryusa-26K) upper and lower doors connected by a common loop - they will have to be re-hung at the same time.
Where can I get plugs for the holes after rehanging?
Usually they come complete with the refrigerator (in package with documentation). diagnosing the defrost system in Samsung No Frost refrigerators. Signs of failure Biryusa or choose the appropriate diameter in a furniture fittings store.