We rehang the door of the Indesit refrigerator: instructions with photos and expert advice

Hanging the refrigerator door Indesit is a task that every owner faces sooner or later. The reasons may be different: inconvenient opening due to the layout of the kitchen, a change in the arrangement of furniture, or a banal desire to update the interior. Fortunately, most of the brand’s models support this function, and you can handle it yourself, without resorting to the services of a specialist.

In this article we will analyze the process hanging the door for refrigerators Indesit of different series - from classic single-chamber to double-chamber with system No Frost. You will learn what tools you will need, how to properly dismantle and install hinges, and also avoid common mistakes that can lead to failure. We will pay special attention to the nuances for models with electronic control and a display - there are some subtleties here.

If you have never done such work, do not worry: step-by-step photos, diagrams and videos (links to which are provided at the end of the article) They will help even a beginner to understand. The main thing is not to rush and follow the instructions. And for those who doubt their abilities, we have prepared preparation checklist a list of signs for which it is better to call a specialist.

We will warn you in advance: the process can take from 1 to 3 hours depending on the model and your experience. But the result is worth it - a correctly hung door will last no less than the original installation from the manufacturer.

Preparation: tools and conditions

Before you start work, make sure that you have everything you need. To hang a refrigerator door Indesit of a standard size (up to 180 cm in height) you will need:

• 🔧 A Phillips screwdriver (usually No. 2) - for most hinges and fasteners.
• 🔧 Hex wrench (size 5 or 6 mm) - for some models with top hinges.
• 📏 Ruler or tape measure —to measure gaps and symmetry.
• 🧲 Magnetic holder (optional)—convenient for fixing small parts.
• 🧴 Silicone grease —for processing hinges after installation.

Also prepare a clean cloth or towel - you can use them to cover the floor so as not to scratch the surface of the refrigerator during dismantling. If your model is equipped with display or touch buttons (for example, Indesit ITF 118 or Indesit BIAA 13), you will additionally need a plastic spatula to carefully remove decorative panels.

Pay attention to door weight: for two-chamber refrigerators it can reach 15–20 kg. If you are working alone, think in advance about how you will support it when removing it. For example, you can place a chair under it or ask an assistant to hold it.

⚠️ Attention: If your refrigerator Indesit was produced before 2010, the design of the hinges may differ from modern models. In this case, check the presence of special plugs for the holes on the opposite side - their absence means that hanging the door is not provided by the manufacturer.

Step 1: Turning off and defrosting the refrigerator

The first stage is ensuring safety. Disconnect the refrigerator from the networkby removing the plug from the socket. If your model is equipped electronic display, wait until it goes out completely (this will take 1-2 minutes). Do not rely on the shutdown button - it only turns off the compressor, but does not de-energize the control board.

Next is necessary defrost the refrigeratoreven if there is no visible ice on the walls. This is due to the fact that when re-hanging the door, the seal may move, and remaining moisture will lead to the formation of condensation or mold. The defrosting process will take from 4 to 12 hours depending on the model:

• 🕒 For No Frost 4-6 hours are enough.
• ❄️ For drip systems - 8-12 hours.

After defrosting wipe all surfaces dry, including rubber seals. Pay special attention to the grooves where the door is attached - water often accumulates there. Use a soft cloth to avoid damaging the coating.

If the refrigerator Indesit is equipped with ice maker or water dispenser (for example, series models Indesit ITR 520), disconnect the water supply hoses and drain remaining liquid. Otherwise, when removing the door, water may flood the electronic components.

Step 2: Dismantling the old door

Now we move on to the most important stage - removing the door. Let's start with upper hinge, since it usually fixes the main weight. Algorithm of actions:

1. Remove the decorative plugs from the hinges (if any). Pry them off with a plastic spatula or a screwdriver wrapped in cloth so as not to scratch the surface.

2. Unscrew the bolts securing the top hinge to the refrigerator body. In most models Indesit this is 2-3 bolts for a Phillips screwdriver. Hold the doorsince after removing the last bolt it can drop sharply.

3. Carefully remove the door from the bottom hinge and set it aside soft surface (for example, a towel). Do not place the door on its side - this may deform the seal.

If you have a two-chamber refrigerator (for example, Indesit BIAA 13 or Indesit DF 5200), first remove the door freezer compartment, then the main one. Between them there is usually an intermediate loop, which also needs to be unscrewed.

Pay attention to power wiresif your model is equipped with a display or backlight. They should not be bent or pulled - it is better to immediately disconnect the connectors (remember or take a photo of the connection order!).

Step 3: Transfer the loops to the opposite side side

After dismantling the door, you need to move the hinges to the other side. There are two options here:

1. Symmetrical holes already on the case (this is typical for most modern models Indesit). In this case, simply unscrew the hinges on one side and attach them to the mirror holes.

2. There are no holes - this happens with older or budget models. Then you will have to drill new holes using a template (usually included with the refrigerator). If there is no template, measure the distance between the holes on the old side and transfer the markings.

For models with electronic control (for example, Indesit ITF 118) it is important to transfer not only the loops, but also wiring. Usually it runs inside the case, and to move it you need to remove the back cover. If you are not confident in your abilities, it is better to entrust this stage to a professional - an incorrect connection can damage the control board.

When moving the loops, make sure that:

• 🔹 The bolts are twisted evenly —do not overtighten so as not to break the thread.
• 🔹 The hinges were standing strictly horizontally —check with a level or ruler.
• 🔹 There was a gap between the door and the body 2–3 mm for the seal.

Critical: if your model is equipped with a system No Frost with a fan in the freezer (for example Indesit BIAA 13 NF), after hanging the door, check the operation of the fan. It should rotate freely, without extraneous noise. If a hum appears, it means that the door is installed incorrectly and is pinching the air ducts.

Step 4: Installing the door on the new side

When the hinges have been moved, you can begin installing the door. Start with the bottom hinge:

1. Carefully slide the door onto the bottom hinge pin, holding it by the top edge.

2. Align the door so that it stands vertically. Check the gaps around the perimeter - they should be the same (2-3 mm).

3. Tighten the top hinge bolts, but not all the way. First, pull them slightly, then check how the door opens and closes.

For two-chamber refrigerators, the process is a little more complicated:

1. The freezer door is installed first.

2. Then - the intermediate hinge (if there is one).

3. Lastly the main door is attached.

After preliminary fixation, check:

• 🔹 The door opens and closes smoothly, without jerking.
• 🔹 Seal fits evenly along the entire perimeter (check with a probe or a sheet of paper - it should not pass freely).
• 🔹 There are no distortions - if the door opens or closes itself, it means the hinges are installed unevenly.

If everything is in OK, finally tighten the bolts. Use a torque wrench (if available) with force 1.5–2 N m - this is enough so that the hinges do not unwind, but the thread remains intact.

Step 5: Checking and adjustment

After installing the door, it is necessary to carry out test run. Connect the refrigerator to the mains and let it work for 1-2 hours as usual. Pay attention to the following points:

• 🌡️ Temperature - if the refrigerator has become worse at cooling, the seal may not be tightly sealed.
• 🔊 Noise - extraneous sounds when opening/closing the door may indicate a misalignment hinges.
• 💧 Condensation —if moisture appears on the seal or walls, check the tightness.

To adjust the door, use top hinge —it usually has play for position adjustments. To adjust the door vertically:

1. Loosen the bolts of the top hinge.

2. Slightly raise or lower the door to the desired position.

3. Tighten the bolts and check result.

If the seal does not fit tightly, it can be corrected:

• 🔹 Local detachment —heat the problem area with a hairdryer (temperature up to 50°C) and press the seal against the body.
• 🔹 General deformation — remove the seal, soak it in hot water for 10 minutes, then install it back.

⚠️ Attention: If, after re-hanging the door, the refrigerator Indesit begins to consume more electricity (this can be seen from the bills or the indicator on the display), it is probably broken tightness. In this case, it is better to return the door to its original position and contact the service center.

Typical mistakes and how to avoid them

Even if you strictly follow the instructions, you can make mistakes that will lead to breakdown or incorrect operation of the refrigerator. Here are the most common of them:

• 🚫 Ignoring defrosting — ice residues can damage the seal or electronics during dismantling.
• 🚫 Tightening the bolts —this leads to thread breakage or deformation of hinges. Use a torque wrench or tighten the bolts “by hand” with moderate force.
• 🚫 Incorrect wiring connection —if you mix up the display or sensor connectors, the refrigerator may not turn on.
• 🚫 Lack of checking the seal —even a small one the gap will lead to increased energy consumption and freezing.

Another common problem is door skew after installation. It manifests itself in the fact that the door itself opens or closes. To avoid this:

• 🔹 Check the horizontalness of the hinges level.
• 🔹 Make sure the bolts are tightened evenly.
• 🔹 Don’t save time - it’s better to check again than to redo it later.

If you encounter a problem that you cannot solve on your own, contact an authorized service center Indesit. In most cases, re-hanging the door will retain your warranty if the work is carried out according to the instructions. However, if you damage the hinges or seal, repairs may be charged.

What to do if the door does not close after rehanging?

If the door does not close completely, check:

1. Are there any foreign objects in the seal.

2. Are the hinges installed correctly (maybe they are skewed).

3. Was the refrigerator body deformed during dismantling?

If the problem remains, return the door to its original position and contact a technician.

FAQ: Frequently asked questions about rehanging the Indesit door

Is it possible to rehang the door on an Indesit refrigerator with a display yourself?

Yes, but with caution. The main thing is to correctly transfer the wiring of the display and sensors. If you are not confident in your skills in working with electronics, it is better to call a specialist. In models like Indesit ITF 118 the wires run inside the case, and they can easily be damaged during careless dismantling.

Do you need to buy new loops for rehanging?

No, in 99% of cases it is enough to move the old loops to the other side. New hinges may only be needed if the old ones are damaged (for example, the threads are broken or the metal is deformed). Original spare parts for Indesit can be ordered by the refrigerator model code.

How to understand that the door is hung correctly?

Signs of correct installation:

• The door opens and closes smoothly, without creaks.
• The seal fits evenly around the entire perimeter (checked with a sheet of paper - it should hold tightly).
• There is no spontaneous opening or closing.
• The refrigerator maintains the set temperature (checked after 12-24 hours).

How much does it cost to rehang the door at the service center?

The cost of the service at official service centers Indesit varies from 1,500 to 3,500 rubles depending on the model and region. In private workshops, the price may be lower (from 1,000 rubles), but there is a risk of running into unqualified specialists. Re-hanging it yourself will be free if you don’t need to buy tools.

Is it possible to re-hang the door on an Indesit refrigerator older than 10 years?

Depends on the model. Refrigerators Indesitmanufactured before 2010 often do not have symmetrical holes for hinges. Before starting work, check:

• Whether there are plugs on the opposite side (if yes, re-hanging is possible).
• If there is rust on the hinges (if there is, it is better to replace them).
• The condition of the seal (if it becomes dull or cracked, it may be necessary after re-hanging replacement).

For older models without symmetrical holes, rehanging is not recommended - this may break the seal.