Re-hanging the refrigerator door Biryusa is a task that many owners face when moving, renovating a kitchen or a banal desire to change the opening side. Despite the apparent complexity, the procedure is quite doable with your own hands if you know the key nuances of the design of domestic models. The main thing is not to rush and follow a proven scheme, taking into account the features of the fastenings and the location of communications.
Unlike foreign brands, refrigerators Biryusa (especially models Biryusa-18S, Biryusa-22K and series KShD) have a unified fastening system doors, but with some variations depending on the year of manufacture. For example, in older modifications before 2010, metal hinges with threaded bushings could be used, while in new ones (after 2015) plastic plugs and self-tapping screws with a hex head were used. This article will analyze both options in detail, and also tell you how to avoid common mistakes that lead to door misalignment or damage to the seal.
Before you begin, make sure that your model really supports overhang - some compact refrigerators (for example Biryusa-50) have an asymmetrical body design, and changing the opening side is impossible without modifications. If in doubt, check the presence of technological holes for loops on the opposite side.
Preparation: tools and conditions
For work you will need:
- ✅ Hex key (usually 5 or 6 mm) - for modern models with loops on bolts.
- ✅ Phillips screwdriver (PH2) - for removing decorative panels and attaching the handle.
- ✅ Wrench (10 mm) - for older models with nuts on hinges.
- ✅ Flat screwdriver —for prying off the plugs and adjusting the seal.
- ✅ Making tape —to secure the door during operation.
- ✅ Level (preferably magnetic) - to check the vertical position after installation.
Also prepare the work space:
- 📏 Clear the area around the refrigerator (at least 1 m on each side).
- 🔌 Turn off the power and let the refrigerator stand for 1-2 hours - this will reduce the pressure in the cooling system.
- 🧊 Remove all food and shelves from the door so as not to damage them.
- 📦 Place cardboard or soft cloth on the floor - this will protect the door covering from scratches.
⚠️ Attention: If your The refrigerator Biryusa is equipped with a display or an electronic control unit on the door (for example, models Biryusa-130 or Biryusa-260), be sure to disconnect the power cable before hanging! Otherwise, you risk damaging the contacts.
Door fastening diagram: what you need to know
The design of hinges Biryusa depends on the series:
| Model series | Type loops | Fastening | Features |
|---|---|---|---|
| Biryusa-18S, Biryusa-22K | Metal, collapsible | M6 bolts with hex head | Replacement of the upper and lower hinges is required |
| Biryusa-KShD (until 2015) | Metal, with nuts | M8 nuts for wrench | You need to remove the decorative trims |
| Biryusa-130, Biryusa-260 | Plastic with metal core | Hexagon screws | There is a display cable - be careful with the wires! |
| Biryusa-50, Biryusa-60 | Non-separable (rivets) | Overhanging is not provided | Requires modification of the body |
In most cases, the hinges are attached to the refrigerator body through 4 holes (2 on top, 2 on bottom), which are closed plugs on the opposite side. Your job is to transfer the hinges to the other side using these existing holes. The exception is models with asymmetrical case (for example, Biryusa-50), where there are simply no holes on the other side.
Critical: before removing the door, take a photo of the location of the hinges and mark the top and bottom with a marker - they should not be mixed up when installing! Otherwise, the door will sag or not close.
What to do if there are no holes on the other side?
If your model does not provide for overhanging (for example, Biryusa-50), you can drill new holes yourself, but this requires precision. Use an 8mm drill bit and a cardboard template, copying the location of the hinges from the original side. After drilling, be sure to paint the edges of the holes to avoid corrosion.
Step-by-step instructions: removing the old door
Start with the top hinge - it usually fixes the door in a vertical position. Act carefully so as not to drop the door!
Close the refrigerator and secure the door with masking tape in the closed position (this will prevent it from falling).
Remove the decorative trim of the top hinge by prying her with a flat screwdriver. In some models, the cover is attached with latches, in others - with self-tapping screws.
Unscrew the bolts (or nuts) of the upper hinge hex wrench or wrench. Do not unscrew them completely - just loosen enough so that the hinge comes off the axle.
Holding the door, carefully remove it from the top hinge and place it on a prepared surface (for example, on a table covered with a blanket).
Now unscrew the bottom hinge completely and remove it from the body.
⚠️ Attention: If the door is equipped with magnetic seal, do not pull it by the edge - this may deform the rubber. Grasp the metal body or handle.
After removing the door, inspect the hinges for corrosion or wear. If the bolts are rusty, treat them WD-40 10-15 minutes before unscrewing. In models Biryusa-KShD older than 2010, hinges with plastic bushings are often found - they need to be removed and moved to the other side along with the bolts.
☑️ What to check before installing the door on the new side
Transferring loops and preparing holes
Now you need to transfer the loops to the other side. There are two scenarios here:
If there are already holes (closed with plugs):
- Remove the plugs from the opposite side by prying them off with a screwdriver.
- Check the threads in the holes - if they are clogged with dust, clean them with a match or toothpick.
- Install the hinges in the new holes and lightly tighten the bolts (do not tighten!).
If there are no holes (models without factory overhang support):
- Use the hinges as a template - attach them to the body and trace them with a marker.
- Drill holes with an 8 mm drill (for M6 bolts) or 10 mm (for M8 nuts).
- Apply to the edges holes
anti-corrosion primerif the case is metal.
For models Biryusa-130/260 with a display additionally:
- 🔌 Disconnect the power cable from the case (usually it is attached to a clip).
- 📶 Move the cable channel for the cable to the other side using standard fasteners.
- 🔧 Check the length of the cable - if it is not enough, you will need an extension cord (buy at a service center Biryusa).
Important: when installing loops on the new side, the top loop should be mirror image bottom. For example, if before the left loop was on top, now the right loop should be on the bottom. By mixing them up, you will get a skew! data-i="185">mirror image
Door installation and adjustment
This is the most important step. Proceed in the following order:
Lift the door and put it on bottom hinge, holding it by the handle.
Align the door vertically and slide it onto the top hinge. Have an assistant hold the door while you tighten the bolts.
Tighten the bolts crosswise (first the top left, then the bottom right, etc.) to avoid skew.
Check the gaps around the perimeter of the door - they should be the same (2-3 mm).
After preliminary fixation:
- 📏 Use levelto check the verticality of the door. If necessary, loosen the bolts and adjust the position.
- 🔄 Close the refrigerator and check how the seal fits. If there are gaps, adjust the hinges (see the next section).
- 🔊 Listen to see if there are any squeaks when opening/closing. If there are any, lubricate the hinges
with silicone grease.
⚠️ Attention: In models Biryusa-KShD with two chambers (refrigerator and freezer), after re-hanging the door may be required the freezer often sags due to weight. Tighten the legs clockwise to raise the body. adjusting the legs — the freezer door often sags due to weight. Twist the legs clockwise to raise the body.
If the door closes too tightly, loosen the top the hinge by 0.5 turns. If, on the contrary, it does not tighten, tighten the lower one. Ideally, the door should close with a slight push with a force of no more than 1-2 kg.
Checking the seal and finishing touches
The sealing rubber is the most vulnerable place after re-hanging. If it is deformed, the refrigerator will waste extra energy on cooling. Check:
- 🔍 Visually: the rubber should fit evenly around the entire perimeter, without gaps or “waves.”
- 📄 "Test with paper": squeeze a sheet of paper between the door and the body. If it falls out, the seal is not sealed.
- 💡 Condensation: after turning on the refrigerator, check if moisture appears at the joints. If so, the seal. allows warm air to pass through.
If the seal is deformed:
- 🔥 Warm it up hairdryer (temperature 50–60°C) and shape it with your hands.
- 🧴 Lubricate the rubber glycerin or special silicone grease for seals.
- 🔧 If the damage is serious (cracks, tears), replace seal to a new one (article for Biryusa Biryusa —
7402-0000120).
The last step is to install the handle and decorative trims:
- Screw the handle to the new side (the holes are usually symmetrical).
- Close the hinges with decorative ones plugs (they should go in with a slight click).
- Make sure that all the screws are tightened, but not overtightened - otherwise the plastic may crack.
Now you can turn on the refrigerator and check its operation. On the first day after rehanging, monitor:
- 🌡️ Temperature in cameras (must correspond to the specified one).
- ❄️ Ice on the back wall (it should not be more than usual).
- 🔊 Extraneous noise (creaks, knocks when opening).
Typical mistakes and how to avoid them
Even with careful work, you can make mistakes that will lead to problems. Here are the most common ones:
| Error | Consequences | How to fix |
|---|---|---|
| The loops are reversed (top bottom and vice versa) | The door sags and does not close | Swap the hinges and adjust the gaps |
| The bolts are unevenly tightened | Door distortion, creaks | Loosen all bolts and tighten crosswise |
| The seal is not moved or damaged | Camera freezing, high power consumption | Warm with a hairdryer or replace the seal |
| Not moved plugs on the old side | Visible holes, dust ingress | Install plugs in the vacant holes |
| The display cable is pinched or damaged | The screen does not work, control errors | Check the integrity of the cable, replace if necessary |
Another common problem is creaking loops after rehanging Reasons:
- 🔩 Insufficient lubrication. (use
silicone greasenot oil!). - 🔧 Overtightened bolts (loosen 0.25 turn).
- 🔄 Hinges are not installed level (check vertical).
If after all the manipulations the door still does not close tightly, check:
- 📏 The geometry of the body — perhaps the refrigerator is not level (adjust the legs).
- 🧲 Sealant magnet —over time it loses strength (replace seal).
- 🔧 Hinge rivets —in older models they may be weakened (replace with M6 bolts).
⚠️ Attention: If your refrigerator Biryusa warranty, re-hanging the door may void it! Check this point with the service center or an authorized dealer.
FAQ: Frequently asked questions about re-hanging the door
Is it possible to re-hang the door by refrigerator Biryusa-50?
Models Biryusa-50 i Biryusa-60 usually do not provide for overhanging due to the asymmetrical case. However, some owners drill new holes themselves. To do this you will need:
- Remove the door and hinges.
- Use the hinges as a template for marking.
- Drill holes with an 8-10 mm drill.
- Install the hinges with new side and adjust.
Risks: violation of the seal of the chamber, damage to the case. If you are not sure, contact the service.
What should you do if, after rehanging, the refrigerator begins to operate loudly?
The noise may be associated with:
- By skewing the door - check the gaps and adjust the hinges.
- By vibration of the body - level the refrigerator by tightening the legs.
- Friction of the seal - lubricate the rubber with glycerin.
- By loosening the compressor fastenings —check the bolts on the rear wall.
If the noise does not disappear, the refrigerant pipeline may have been damaged when re-hanging. In this case, a technician needs to diagnose it.
How to move the handle to the other side?
In most models Turkish the handle is attached to symmetrical holes. To transfer it:
- Unscrew the screws on one side (usually 2-3 pieces).
- Remove the handle and install it on the opposite side.
- Tighten the screws, but do not overdo it - the plastic may crack.
If there are no holes on the other side, you can:
- Use the handle without fastening (on clips).
- Drill new holes and insert
bushingsfor self-tapping screws.
Do I need to defrost the refrigerator before rehanging?
Absolutely! Here's why:
- 💧 During operation, the refrigerator may tilt, and water from defrosting will get onto the electronics.
- ❄️ Ice on the walls adds weight to the door, which makes it difficult to remove.
- 🔧 When defrosting, the seal becomes more elastic and smaller deformed.
We recommend defrosting the refrigerator 12–24 hours before starting work and wiping all surfaces dry.
Where to buy spare hinges or seals for Biryusa?
Original spare parts can be ordered:
- 🏬 In branded service centers Biryusa (list on the official website).
- 🛒 In online spare parts stores:
4holoda.ru,zapchasti-msk.ru,220-volt.ru. - 🔧 In refrigerator repair shops (they often sell used parts in good condition).
Articles of popular spare parts:
- Upper hinge:
7401-0000045. - Bottom hinge:
7401-0000046. - Seal (standard):
7402-0000120. - Seal (for freezer):
7402-0000121.
The cost of hinges is from 300 to 800 rubles, the seal is from 1,200 to 2,500 rubles (depending on the model).