The need to change the side opening the refrigerator door Beko often occurs when moving to a new kitchen or after remodeling the room, when the standard location interferes with convenient access to products. Many owners of household appliances mistakenly believe that this is a complex engineering task that requires calling a paid technician, but most models are designed with basic tools and care. The process takes from 30 to 60 minutes and does not require special technical knowledge if you strictly follow the sequence of actions. provides for self-installation with basic tools and care. The process takes from 30 to 60 minutes and does not require special technical knowledge if you strictly follow the sequence of actions.
Before starting work, it is important to clear the space around the unit to ensure free access from all sides, including the top and back of the case. Safety is a priority, so the first step should always be to turn off the device from the electrical network to avoid accidental electric shock or damage to electronics due to careless handling of wires. It is also recommended to prepare all the necessary tools in advance so as not to interrupt the process of searching for a screwdriver or key.
In modern models Beko, such as series CN, RCNE or RCSA, the hinge mechanism may differ in fastening details, but the general the principle remains the same for most two-chamber refrigerators. You will need a Phillips screwdriver, a flat-head screwdriver to remove the trim caps, and possibly an 8mm or 10mm wrench depending on the year the unit was made. It would be a good idea to call an assistant, since removing a heavy door without the risk of dropping it or damaging the shelf is easier to do with two people.
Preparation of tools and workplace
Quality preparation directly affects the speed and result of the work, so you should not ignore this stage even if you have minimal experience. You will need a set toolsthat is usually found in every home: a Phillips screwdriver (PH2), a flathead screwdriver, a wrench (often 8 mm) and pliers. For some models Beko with the No Frost system, a hex key may also be required if the hinge screws are hidden under decorative caps of a specific shape.
Particular attention should be paid to the organization working area. Move the refrigerator at least one meter away from the wall so that you can easily walk around it. Cover the floor with thick cardboard or an old blanket - this will protect the floor covering from scratches if you have to replace the removed door, and will prevent the unit from sliding. Make sure there is good lighting in the work area, as some fasteners may be small and hard to see in the shade.
Before you start unscrewing the hinges, be sure to Remove all removable elements from the doors: shelves, egg containers, baskets and decorative trims. This significantly will reduce weight design will reduce the risk of glass shelves accidentally falling during dismantling. If your model Beko has a display or control panel on the door, make sure you know how to carefully disconnect the cable without damaging the contacts.
Removing the top door and removing the hinges
The process starts from the upper chamber of the refrigerator, since It is this that creates the main load on the structure if removed incorrectly. First you need to remove the decorative plug from the top hinge, under which the mounting bolts are usually hidden. Use a flathead screwdriver to carefully pry up the plastic, without using excessive force to avoid breaking fasteners or scratching the case.
After gaining access to the fasteners, loosen the top hinge bolts, but do not unscrew them completely yet. At this stage it is critical that someone fixed the door in an upright position, otherwise it may fall along with the loop. If you work alone, you can use small wedges or pads under the bottom of the door, but this is less reliable and requires increased caution.
⚠️ Attention: In models Beko with the Multi Air Flow system or similar cold distribution technologies, wiring often runs through the top hinge. Before completely removing the hinge, make sure that you carefully pull out the wire connector without pulling the cable sharply.
☑️ Removing the top door
When the top hinge is completely freed from bolts and wires, remove it along with the top door. Place the door on a prepared soft surface with the outer side down, placing a cloth under it. Now similar steps need to be repeated for the bottom door if you plan to rehang both doors, which is a standard procedure for two-chamber refrigerators.
Reversing the bottom door and freezer
The bottom part of the refrigerator Beko, be it the freezer or the main compartment, often has its own mounting features, especially in models with drawers. To begin, remove the plinth grille at the bottom of the refrigerator, if there is one, to gain access to the bottom support hinge. Unscrew the fastening bolts holding the hinge and remove it, after first lifting or fixing the door.
An important point is the rearrangement stop pins and bushings. In most models Beko the door is symmetrical, and there are holes for hinges on both sides, but the factory pins are installed on only one. You need to remove the pin from the current hole and move it to a symmetrical hole on the opposite side of the door. This will ensure the correct positioning of the door after installation.
If your model is equipped with handles integrated into the body or has an asymmetrical design, make sure that repositioning the door is possible in principle. Some budget or designer series may have asymmetrical structurenot implying overweight, although Beko this is rare. Check for threaded holes on the other side before starting active operations.
What to do if the holes do not match?
In rare cases, the holes can be closed with plastic plugs. Carefully remove them from the back side and install them in place of the old holes to maintain aesthetics.
After preparing the holes and transferring the pins, install the bottom support loop on the new side. Do not tighten the bolts all the way yet, leave a small gap for subsequent adjustments. Hang the lower door on the hinge and check how freely it moves and whether it fits tightly to the body when closed.
Installing the upper door on the new side
Installing the upper door on the new side requires careful alignment of the rotation axes. Lift the door and put it on the lower pin (if the structure is composite) or directly on the prepared upper hinge, which should now be secured on the opposite side of the body. Make sure that the axes fit into their seats without distortions, otherwise the door will be skewed and will not close hermetically.
When installing the top hinge, do not forget to pass the control or lighting system wires through special channels in the hinge, if this is provided for by the design of your models Beko. Connect the connectors before fully tightening the bolts so that you can correct the connection. Check the functionality of the indicators and display (if any) immediately after connection, before complete assembly.
| Element | Action | Tool | Nuance |
|---|---|---|---|
| Top loop | Shift to the other side | Phillips screwdriver | Careful with the wires |
| Bottom loop | Dismantling and installation | Wrench (8-10 mm) | Check the pins |
| Door handles | Removal/Installation (if removable) | Hexagon | Do not strip the thread |
| Plugs | Repositioning to old holes | Flat screwdriver | For aesthetics |
Secure the top hinge with bolts, but, as in the case of the bottom, do not tighten them with maximum force yet. This will allow you to carry out an accurate one at the next stage. Make sure that the door is level and does not fall to either side. adjusting the gaps. Make sure the door is level and not tilting to either side.
Adjusting the gaps and tightness
The final and, perhaps, the most important step is adjusting the position of the doors. An incorrectly adjusted door will lead to a loose fit, which will cause constant operation of the compressor, the formation of ice and increased energy consumption. The gap between the door and the body must be uniform around the entire perimeter. seal, which will cause constant operation of the compressor, the formation of ice and increased energy consumption. The gap between the door and the body must be uniform around the entire perimeter.
To adjust, use the adjusting screws on the hinges (usually they are located on the front or side of the hinge). By rotating them clockwise or counterclockwise, you can move the door up and down or closer or further from the body. In models Beko often it is enough to loosen the hinge mounting bolts half a turn, set the door to the desired position and tighten them again.
⚠️ Attention: If after adjustment the door still does not fit tightly, check the cleanliness of the sealing rubber. Dirt or packaging residue may interfere with the seal. Also make sure that the refrigerator is strictly horizontal - use a building level to check.
Check the operation of the doors several times, opening and closing them. They should move smoothly, without squeaks or jams, and when closing, be tightly magnetized to the body. If you hear a characteristic suction sound when reopening a minute after closing, it means vacuum it is created correctly and tightness is ensured.
Common mistakes and troubleshooting
When rearranging doors on their own, users often make typical mistakes that can ruin all your work. One of the most common is forgetting to rearrange thrust pin on the door itself. If you leave the pin in the old hole, the door simply will not fit into the new place or will dangle.
Another mistake is over-tightening the hinge bolts before the final check of the position. This may cause the metal of the hinge or housing to warp, making fine adjustments impossible. Always set the geometry first and then record the result. They also often forget to replace the plastic plugs on the vacated holes, which spoils the appearance device.
If the door creaks after installation, try lubricating the rubbing parts of the hinges with a small amount of silicone grease (do not use oil or grease, they will attract dust). If the door touches the body when opening, check whether the refrigerator itself is twisted - sometimes it is enough to simply tighten the front support legs.
Why is the door not held in place by a magnet?
If the magnets in the seal are loose or the door is skewed, the tightness is broken. Try heating the seal with a hairdryer or replacing it if it is deformed.
Carefully inspect all wire connections if your model Beko is equipped with electronics on the door. Poor contact may result in an error on the display or system failure No Frost. If after assembly the refrigerator behaves strangely, double-check the wiring diagram.
FAQ: Frequently Asked Questions
Do I need to defrost the refrigerator before rearranging the doors?
Yes, this is highly recommended. First, an empty refrigerator is easier to move and tilt. Secondly, when tilting (even minimally), oil from the compressor can flow into the cooling system, which is undesirable. Allow the unit to stand unplugged for several hours after defrosting before turning it back on.
Is it possible to reverse the door on a Beko refrigerator with a display?
Yes, you can, but it requires more care. The length of the wire loops in such models usually allows you to rearrange the door, but you need to be very careful when disconnecting and connecting connectors so as not to damage the thin contacts.
What to do if the length of the wires is not enough when rearranging?
In the original models Beko the length of the wires is designed for rearrangement. If the wires are stretched, check that you have laid them correctly in the cable channels. You cannot stretch them by force - you can damage the insulation or contacts. If the wires are really short (for example, after a previous poor-quality repair), an extension will be required from a specialist.
Will the warranty remain valid after self-rearrangement?
According to the law, self-rearrangement of doors is not a complex repair and should not void the warranty if you have not damaged the unit components. However, if you break a loop or cable in the process, it will not be covered under warranty. Keep all removed parts.