We rehang the door of the Indesit refrigerator yourself: instructions with photos and advice

Rearranging the refrigerator door Indesit is a task that many owners face when moving, renovating a kitchen, or simply wanting to change the opening side. Despite the apparent complexity, the procedure is quite doable at home if you know the key nuances. The main thing is to take your time and follow the logic of the design: the manufacturer has provided the possibility of outweighing, so all fastenings are symmetrical.

In this article you will find step-by-step instructions with photosan analysis of typical errors, as well as tips for working with models of different series (Indesit C 132 G, BIAA 13, DF 4180 W etc.). We will pay special attention to points that are often missed in standard manuals: how to properly remove decorative plugs, how the process differs for refrigerators with water dispenser, and how to avoid warping the door after installation.

Before Before you start, check: does your model really support overweight? Some budget lines (for example Indesit ITF 118 W) have door hinges that are not symmetrical - in this case, the fittings will need to be replaced. Check this in device passport (section "Technical Specifications" or "Design Features").

1. Preparation: tools and conditions

For work you will need:

• ⚒️ Phillips screwdriver (preferably magnetic so as not to lose small screws)
• 🔧 Wrench 10 mm (for some models - 8 or 12 mm)
• 📏 Level (to check horizontality after installation)
• 🧲 Magnet or tape (to temporarily fix the door when removing)
• 🧴 Silicone grease (for hinges after reinstallation)

Important: unplug the refrigerator 1-2 hours before starting work. This is necessary not only for safety, but also to ensure that the compressor cools down - this way you will avoid the risk of damage to the seal when dismantling the door. If your model has a function. Super Cool or Super Freeze, disable it in advance.

⚠️ Attention: Do not hang the door when the room temperature is below +10°C. Plastic parts become fragile and may crack during dismantling.

Prepare the work space:

• 📦 Clear the shelf in front of the refrigerator (at least 1.5 m wide).
• 🧹 Lay down soft cloth or cardboard - this will protect the floor from scratches if the door accidentally falls.
• 🔦 Organize good lighting, especially if the hinges are located at the bottom.

Make sure that the model supports hanging|Unplug the refrigerator in advance|Prepare tools and spare parts (if necessary)|Free up space around the refrigerator|Take a photo initial position of hinges and fastenings -->

2. Removing the door: step-by-step process

Start with the top hinge - it usually holds the main load. Algorithm of actions:

1. Remove decorative plug from the top loop. It is attached with latches - pry it off with a flat screwdriver or knife (carefully so as not to scratch the plastic). In some models (Indesit BIAA 13), the plug can be screwed on with a screw - it needs to be unscrewed.

2. Unscrew fastening screws hinges (usually 2-3 pieces). In models with a dispenser, there may be an additional clamp for the hose - do not lose it!

3. Holding the door, remove it from bottom hinge pin. It is better to do this together: one person lifts the door, the second pulls it up at an angle of 30–45°.

If the door is “jammed” and cannot be removed, check:

• 🔹 Did you remember to unscrew all the screws (sometimes one is hidden under a sticker).
• 🔹 Is there an additional lock in the bottom hinge (typical for models Indesit C 168 NF and similar ones).
• 🔹 Does the seal get in the way - it can be slightly bent.

⚠️ Attention: On the doors s water dispenser before removing, be sure to disconnect the water supply hose! It is attached to the back wall of the refrigerator with a clip. If you do not do this in advance, you can damage the connection.

After removing the door:

• 📸 Take a photo of the location of the hinges and holes - this will help with reassembly.
• 🧹 Clean the hinge pins from old grease (use alcohol or a special cleaner).
• 🔄 Move decorative plugs i fastening screws to the opposite side.

What to do if the hinge screws cannot be unscrewed?

If the screws are stuck or the threads are broken, try the following methods:

1. Apply WD-40 or similar lubricant to the threads, wait 10-15 minutes.

2. Use a screwdriver with an extended blade for better support.

3. Use a wrench instead of a screwdriver (select the slot size).

4. As a last resort, drill out the screw with a drill with a thin drill bit (only if you plan to replace the hinges!).

3. Transferring hinges and fasteners to the other side

Now you need to prepare the refrigerator for installing the door on the new side. There are two scenarios here:

General algorithm for most models:

1. Unscrew install the lower hinge and transfer it to the opposite side. Please note: the holes for fastenings are already provided by the manufacturer (they are closed with plugs).

2. Install top hinge in a mirror. models Indesit C 132 G and similar ones are attached here door-stop (the stop that limits the opening angle) - it also needs to be moved.

3. If your model has middle hinge (typical for tall refrigerators), repeat the procedure for it as well.

Critical important: When transferring the hinges, do not confuse the upper and lower ones! They differ in design: the upper one usually has an adjusting screw for aligning the door, and the lower one has a pin for hanging. In models Indesit BIAA 13 the upper hinge also contains a door opening sensor - it cannot be damaged!

For models with a dispenser:

• 💧 Move control unit (if it is located on the door) to the other side. To do this, disconnect the connectors and cover them with plugs.
• 🔌 Reinstall water supply hose. In some cases you will need to extend it (you can use the original hose Indesit art. C00300956).

4. Installing the door on the new side

This is the most critical stage. Follow the instructions:

1. Place the door onto lower hinge pin, lifting it at an angle of 45°. Make sure that the seal does not interfere with movement.

2. Lower the door so that the top edge fits into the groove of the upper hinge. Here you may need the help of a second person.

3. Tighten the screws of the top hinge, but not all the way - leave some play for adjustment.

4. Check how the door closes. If it opens spontaneously or clings to the body, adjustment is needed.

For adjustment:

• 🔩 Loosen the top hinge screws and adjust the door's vertical position.
• 📐 Use a level to make sure the door hangs level. The permissible skew is no more than 2 mm.
• 🔧 If the door sag, tighten the bottom hinge (but do not overdo it - this may deform the seal).

After installation:

• 🧴 Apply silicone grease on the hinge pins - this will prevent squeaking.
• 🧼 Wipe the seal with soapy water - fingerprints could remain on it.
• 🔌 Connect the refrigerator to the network and check if condensation on the seal (this is a sign of a loose fit).

⚠️ Attention: If, after hanging, the door closes with force, do not try to “rub” it in with force! This will lead to deformation of the seal. Instead, loosen the hinges and adjust the position again.

5. Features for models with a dispenser

Refrigerators Indesit with a water supply system (DWF 16, DWA 14 etc.) require additional manipulations:

1. Disconnecting the hose. Before removing the door, disconnect the hose from the back panel (usually it is secured with a clip). Be careful - there may be water left in the hose!

2. Moving the control unit. If the control panel is located on the door, it must be removed by disconnecting the connectors. In models Indesit C 168 NF the block is secured with 4 screws.

3. Hose extension. When rehanging, the hose may not reach the new hole. Use the original extension Indesit (art. C00300956) or a universal adapter.

4. Check tightness. After installation, start the water supply and check for leaks at the connections.

Typical mistakes when working with a dispenser:

• 🚫 Ignoring the hose clip. If you do not fix the hose, it may bend, which will block the water supply.
• 🚫 Confusion of control unit connectors. In models with a display the connectors may be asymmetrical - check the diagram in the instructions.
• 🚫 Use of non-original hoses. Cheap analogs may burst under pressure.

If after rehanging the dispenser does not works:

• 🔌 Check whether the hose is connected to the pump (it is located at the bottom of the rear wall).
• 💡 Make sure that the control unit is correctly connected to the board (in models Indesit DF 5200 W the connector is marked as "J3").
• 🚰 Start the water supply test mode (hold the dispenser button for 5 seconds).

6. Checking and testing after rehanging

Do not rush to put the products back! First, make sure that everything works correctly:

1. Tightness test. Close the door and check the seal around the entire perimeter. If there are gaps of more than 1 mm, adjust the hinges.

2. Checking the temperature. Install the thermometer on the middle shelf and turn on the refrigerator. After 2 hours, the temperature should be +4...+5°C.

3. Test the dispenser (if any). Pour a glass of water - the flow should be smooth, without air bubbles.

4. Noise control. When opening/closing the door it should not there may be creaking or extraneous sounds.

Typical problems and their solutions:

If after all the manipulations the door still does not close tightly, the reason may be a deformed seal. In this case:

• 🔥 Warm the seal with a hairdryer (temperature 50–60°C) and shape it with your hands.
• 🧴 Apply a special lubricant for rubber to the seal (for example, WD-40 Specialist).
• 🛒 If the seal damaged - replace it (original for Indesit - art. C00194053).

7. Common mistakes and how to avoid them

Even experienced craftsmen sometimes make mistakes when hanging the door:

• 🚫 Use the wrong tools. For example, trying to unscrew the hinge screws with a knife or pliers. This will strip the splines and make the job more difficult.
• 🚫 Apply excessive force. If the door cannot be removed, do not pull it - check that all the screws are unscrewed.
• 🚫 Ignore the instructions for the specific model. For example, Indesit BIAA 13 there is a hidden screw under the sticker on the top hinge.
• 🚫 Forget about the door opening sensor. In some models it is built into the top hinge - if it is damaged, the refrigerator will constantly squeak.

A few more nuances:

• 🔋 Do not turn on the refrigerator immediately after hanging it. Wait 30-60 minutes - this time is needed to stabilize the pressure in the refrigerator. system.
• 🧲 If there are magnetic note holders on the door, remove them before work - they may interfere with removal.
• 📏 In two-chamber refrigerators (Indesit C 168 NF), first hang the freezer door, then the refrigerator door.

If you are faced with a non-standard situation (for example, the hinges are not symmetrical or there are no holes on the new side), do not try to improvise. Contact the service center Indesit - some models require special components for rehanging.

⚠️ Attention: The design of the hinges and fasteners may differ depending on the year of manufacture of the refrigerator. For example, in models Indesit before 2018, hinges with plastic bushings were used, which easily broke during careless dismantling. Check the specifics of your model in the documents or on the manufacturer’s website.

8. When is the best time to contact a specialist? data-i="267">Although re-hanging a door is a task that is feasible for most users, there are cases when it is better to trust professionals:

Although hanging a door is a task that is feasible for most users, there are cases when it is better to trust the professionals:

• 🔧 If your model Indesit is older than 10 years, the hinges could be deformed, and their replacement will require special tools.
• 💧 If refrigerator with a system No Frost and dispenser - an error when connecting the hoses can lead to a leak.
• 🔊 If, after re-hanging, constant noise (hum, vibration) appears, this may indicate a displacement of the compressor.
• 🚪 If the door "sags" by more than 5 mm after installation, it is possible the hinges are worn out and require replacement.

The cost of professional re-hanging in service centers Indesit ranges from 1,500 to 3,000 rubles (for 2026) This amount usually includes:

• Diagnostics of the condition of the hinges and seal.
• Moving fasteners and adjusting the door.
• Checking the tightness and functionality of the dispenser (if any).

If you decide to contact the service, prepare the following information:

• 📄 The exact model of the refrigerator (located on a sticker inside the chamber or on the back wall).
• 📅 Year of purchase (this will help the technician understand the design of the hinges).
• 📸 Photo of the current condition of the hinges and fasteners (if there is visible damage).

FAQ: Answers to frequently asked questions

Is it possible to hang the door on an Indesit refrigerator without an assistant?

Technically yes, but it's difficult. The door weighs 10–15 kg, and holding it with one hand while tightening the screws is problematic. If there is no one to help, use belt ties or magnetic holdersto temporarily fix the door in the desired position. As a last resort, place a soft stand under it (for example, a folded blanket) to avoid scratching the floor.

What to do if, after re-hanging, the refrigerator begins to operate louder?

This is normal in the first 1-2 days - vibration may increase due to changes in the load on the hinges. However, if the noise does not go away, check:

• 🔹 The level of the refrigerator (it should be level, without distortions).
• 🔹 The tightening of the hinges (too tight can deform the body).
• 🔹 The condition of the compressor shock absorbers (they could move when moving refrigerator).

If the noise is similar to metal scraping, immediately turn off the refrigerator - this may indicate that the compressor tubes are touching the housing.

How to rehang the door if the hinges are asymmetrical?

In some models Indesit (for example, ITF 118 W) the loops are not designed for hanging. In this case, there are two options:

1. Buy set of hinges for the opposite side (original spare parts can be found under art. C00194054 for the upper and C00194055 for the lower hinge).

2. Order universal hinges with symmetrical fastening (suitable for most refrigerators Indesit/Ariston).

The cost of a new set of hinges is from 800 to 2,000 rubles. Installation takes 20–30 minutes.

Do you need to lubricate the hinges after rehanging?

Yes, this is necessary! Use silicone grease (for example, Liqui Moly Silicon-Fett) or special lubricant for refrigerators. Apply it in a thin layer on:

• 🔹 Hinge pins.
• 🔹 Threads of mounting screws.
• 🔹 Plastic bushings (if your model has them).

Do not use WD-40 or machine oil - they attract dust and can thicken over time.

Is it possible to hang the door on the freezer separately?

In two-chamber refrigerators Indesit (for example C 168 NF) the freezer door is hung independently from the main one. The process is similar:

1. Remove the upper and lower hinges of the freezer.
2. Move the fastenings to the other side.
3. Install the door and adjust its position.

Please note: in some models the freezer compartment has additional lock (for example, in Indesit ITF 218 WIt also needs to be moved to a new one). side.