We rehang the LG refrigerator doors yourself: instructions with photos and tips

Re-hanging the refrigerator door LG is a task that many owners face when moving, renovating a kitchen, or simply wanting to optimize space. Unlike other brands, equipment from the Korean manufacturer has its own design features that are important to consider. For example, models with a system No Frost require care when working with seals, and two-chamber refrigerators require precise adherence to the sequence of actions for the upper and lower doors.

Despite the apparent complexity, the procedure does not require professional skills. It is enough to have a standard set of tools on hand and 1-2 hours of free time. The main thing is to take your time and follow the algorithm, taking into account the type of your model (LG Door-in-Door, InstaView or classic series). In this article, we will look at step-by-step instructions, common mistakes and give tips on how to avoid damage to the case or opening mechanism.

⚠️ Mounting parts and hole locations may vary depending on the year of manufacture of the refrigerator. If your model is older than 2018, we recommend that you check the diagram in the official documentation or on the website LG by model number (you will find it on the sticker inside the camera).

1. Preparation: tools and conditions

Before you start work, make sure that you have everything you need. Missing even one tool can delay the process or lead to damage to parts. For example, using the wrong screwdriver often causes the splines on bolts to break off.

Here is a complete list of what you will need:

• ⚒️ Phillips and flathead screwdrivers (preferably magnetic, so as not to lose bolts)
• 🔧 A set of wrenches or sockets (usually required size 10 mm)
• 📏 Tape measure or ruler (to check gaps)
• 🧲 Magnet or bowl (to fold small parts)
• 🧴 Hinge lubricant (silicone or special for refrigerators)
• 🧻 Soft cloth and alcohol (to clean the seal)

Also prepare the work space:

• 🚪 Clear access to the refrigerator from all sides - at least 1 meter of free space.
• 🔌 Turn off the power and remove all food (the door is easier remove if the chambers are empty).
• 🧊 If the refrigerator was in operation, wait 1-2 hours for the condensation to evaporate.

2. Removing the old doors: step-by-step algorithm

We start with the top door (if you have a two-chamber model). This is important because the bottom door is often attached to the top door through a common hinge. Trying to remove the bottom one first can lead to distortion or damage to the mechanism.

Proceed according to the following plan:

1. Open the door 90 degrees and fix it (you can place a book or ask an assistant to hold it).
2. Remove the decorative plugs from the hinges - they are usually snapped or screwed with self-tapping screws. Pry them off with a flat-head screwdriver, starting from the bottom edge.
3. Unscrew the bolts securing the top hinge to the refrigerator body (usually 2-3 pieces). Do not unscrew them completely - loosen enough so that the door comes off the hinge.
4. Carefully lift the door up and remove it from the lower hinge. If it is tight, check that all the bolts are unscrewed.

For the lower door (in two-chamber models):

• 🔹 First unscrew the middle hinge connecting the upper and lower doors.
• 🔹 Then remove the lower hinge as described above.
• 🔹 If the freezer door is heavier than usual, have a helper support it while removing it.

⚠️ Attention: In models with the system Door-in-Door (for example LG GR-B247JVQA) the inner door is removed separately. Do not try to remove it together with the main one - this will lead to damage to the opening mechanism.

3. Transferring hinges and plugs to the other side

After removing the doors, it is necessary to transfer the fastenings to the opposite side. The main thing here is not to mix up the holes and damage the threads. In most models LG the holes for the hinges are already provided from the factory, but are closed with plugs.

How to proceed:

1. Remove the plugs on the other side of the case (they are usually plastic and can be removed with a flat screwdriver).
2. Move the hinges to new side using the same bolts. Do not tighten them completely —first you need to align the door.
3. If there are no holes (rare, but happens in older models), you will have to drill them yourself. Use a metal drill with a diameter of 4-5 mm and be sure to protect the surface with masking tape.

For models with hidden hinges (for example, LG InstaView ThinQ):

• 🔹 The hinges are hidden under the decorative panel. First remove it by snapping the clips around the perimeter.
• 🔹 Transferring the hinges requires care - they cannot be mixed up (the upper and lower ones are different in shape).

4. Installing the doors on the new side

This is the most critical stage. The door must stand up straight, without distortions, otherwise the seal will not fit tightly, which will lead to loss of cold and heat. increase energy consumption.

Procedure:

1. Place the top door on the hinges, starting with the bottom hinge. Make sure it moves up and down freely.
2. Align the door vertically (use a level or visually check the gaps at the top and bottom - they should be identical).
3. Tighten the bolts of the upper hinge, but not completely. Check how the door opens/closes.
4. Install the lower door (for two-chamber models), connecting it to the upper one through the middle hinge.

Checking the correctness. installation:

• 🔹 The door should open smoothly, without creaks.
• 🔹 The seal should fit evenly around the entire perimeter (check with a piece of paper - it should not fall out when the door is closed).
• 🔹 The gaps between the door and the body are the same on top and from below (a discrepancy of up to 1 mm is acceptable).

⚠️ Attention: If after installation the door opens by itself at an angle of inclination of the refrigerator of more than 15°, this means that the hinges are overtightened or installed asymmetrically. Loosen the bolts and adjust the position.

5. Adjusting and checking the tightness

Even if the door is visually level, this does not guarantee tightness. compressor.

How to adjust:

• 🔧 If the door sags, tighten the bolts on the hinge that is closer to the problem corner.
• 🔧 If the seal does not fit in one place, loosen the opposite hinge and slightly move the door in the desired direction.
• 🔧 To check the tightness, use a flashlight: in a dark room, direct the light inside the closed refrigerator. If a gap is visible, the seal requires adjustment.

Frequent errors and their consequences:

• 🚫 Overtightened bolts → deformation of the hinges, creaking when opening.
• 🚫 Mismatch of holes → the door hangs crookedly, the seal wears out faster.
• 🚫 Ignoring the middle hinge (in two-chamber models) → the lower door clings to the upper one.

In models with a system Smart ThinQ (for example LG SXS Series) after rehanging the doors, you may need to reset the display settings. To do this, hold the button Ice+ 10 seconds until a sound signal appears.

6. Features for different series of LG refrigerators

The design of hinges and doors varies depending on the series. Let's look at the key differences:

Door-in-Door Series:

• 🔹 The inner door is removed separately - first the main door, then the mini door.
• 🔹 The hinges have additional latches that need to be snapped off before removal.

InstaView series (with transparent panel):

• 🔹 The door is heavier than usual due to the glass insert - an assistant is definitely needed.
• 🔹 The hinges are reinforced, but the bolts require more careful tightening (risk of damage to the glass).

Classic models (for example, LG GA-B429):

• 🔹 Standard hinges with 2-3 bolts, symmetrical holes for the left/right side.
• 🔹 The seal can be removed and washed with warm water before installation.

What to do if there are no holes for hinges?

In some older models LG (before 2015), holes for alternative fastening of hinges are not provided. In this case, you will have to drill them yourself. Use a metal drill with a diameter of 4 mm and be sure to protect the surface of the refrigerator with masking tape. The location of the holes can be determined by the symmetry of the existing ones. according to the technical documentation of the model.

7. Care after re-hanging: tips for extending the service life

After successfully re-hanging the doors, the refrigerator requires special care in the first weeks of operation. This will help to avoid problems with the seal and hinges.

What to do immediately:

• 🧼 Wipe the seal with a weak solution of vinegar (1:1 with water) - this will remove the factory grease and improve the fit.
• 🛠️ Apply silicone grease to the hinge hinges (not on the rubber!).
• 📝 Write down the date of rehanging - check the tightness after 3 months again.

What to avoid:

• 🚫 Do not hang heavy objects (bottles, cans) on the door in the first 2 weeks - the hinges should “get in”.
• 🚫 Do not open the door sharply - this may disrupt the adjustment.
• 🚫 Do not use abrasive cleaners on the seal.

⚠️ Attention: If, after rehanging, the refrigerator begins to operate louder, check whether the door is catching the internal shelves when opening. This may indicate a misalignment that will worsen over time.

Frequently asked questions (FAQ)

Is it possible to rehang the door on an LG refrigerator yourself if you have no experience?

Yes, the procedure does not require professional skills, but it is important to follow the instructions and take your time. The main risks for beginners are: overtighten the bolts (which will lead to deformation of the hinges) or incorrectly align the door. (due to which the seal will not fit). If in doubt, practice unscrewing/tightening the bolts without removing the door.

How long does it take to rehang the doors?

On average - 1-2 hours for a two-chamber refrigerator and 40-60 minutes for a single-chamber refrigerator. The most time is spent on adjustment and checking. tightness. If the model is with a system Door-in-Door, add another 30 minutes to work with the inner door.

Do you need to call a technician after re-hanging it yourself to check?

Usually this is not required if you followed the instructions and the door opens/closes smoothly and the seal fits. evenly. However, if you notice increased noise, ice formation or uneven cooling, it is better to invite a specialist to diagnose.

What to do if, after hanging, the door does not close tightly?

There may be different reasons:

• 🔹 Hinges are skewed - loosen the bolts and adjust the position of the door.
• 🔹 Wear of the seal —try warming it with a hairdryer (temperature 50-60°C) to restore elasticity.
• 🔹 Ingress of debris —check if anything is preventing the closure (for example, crumbs or labels on seal).

If the problem does not disappear, the hinges or body may have been damaged during installation.

Is it possible to reverse the door on an LG refrigerator with a display (Smart ThinQ)?

Yes, but there are nuances:

• 🔹 Before removing the door, unplug the refrigerator for 10 minutes - this will reset the display settings.
• 🔹 After installation, you may need to recalibrate the sensor (instructions in the user manual).
• 🔹 Avoid getting moisture on the electronic unit during operating time.