Rearranging furniture in the kitchen or changing the layout of the room often requires moving the refrigerator to another corner. At this moment, many owners of brand appliances Pozis face a problem: the door opens in the wrong direction, blocking the passage or interfering with neighboring cabinets. Fortunately, the design of most modern models provides the ability to change the side of the hinge, which allows you to adapt the unit to new operating conditions without loss of functionality.
The process of rehanging the door leaf on refrigerators Pozis is not technically difficult, but it requires care and adherence to a certain sequence of actions. Incorrect installation of hinges or loss of fasteners can lead to misalignment of the sash, failure of the seal and, as a result, increased energy consumption. Therefore, before starting work, you need to carefully study the design of your device and prepare the appropriate tools.
In this guide, we will look in detail at how to hang the Pozis refrigerator door, based on the technical features of various series of this brand. We will look at the nuances of working with two-chamber and single-chamber models, pay attention to adjusting the gaps and answer frequently asked questions. Correct reinstallation ensures that your refrigerator will last a long time and effectively store food.
Necessary tools and workplace preparation
Before you begin dismantling door hinges, it is important to ensure safe and comfortable working conditions. A refrigerator is a large and heavy device, so the space around it is a critical factor. It is recommended to move the unit at least one meter away from the wall in order to have access to it from all sides. Also, be sure to disconnect the device from the power supply by unplugging the plug from the socket and allow the compressor to cool for 10-15 minutes.
To perform the work, you will need a standard DIY kit. In most cases, it is enough to have a Phillips screwdriver and a wrench or socket of the appropriate size on hand (usually 8, 10 or 12 mm, depending on the model). Some modern modifications Pozis can be equipped with special decorative plugs, which require careful handling so as not to damage their plastic structure when removed.
- 🔧 Phillips and flat-head screwdriver (sizes PH2, SL4).
- 🔩 Wrench or ratchet with a set of heads (8-13 mm).
- 🧤 Work gloves to protect hands from sharp edges and dirt.
- 🧹 Clean rags for wiping hinges and removing old grease.
☑️ Preparation for rehanging
Particular attention It is worth paying attention to the stability of the refrigerator during operation. Since the center of gravity will shift after removing one of the doors, the unit may become unstable. Fixing the position the housing will help to avoid equipment falling and injury. If the refrigerator came with special shipping bolts or wedges, they can be used for temporary fixation, although in domestic conditions it is usually enough to just hold the body or work with an assistant.
Design features of Pozis refrigerator doors
Refrigerators Pozis are available in various modifications: single-chamber, double-chamber, as well as models with the No Frost system and drip defrosting. The design of their door units may differ. In classic two-chamber models, the upper and lower doors have independent fastening systems, which allows you to change the opening side for each leaf separately or together. Single-chamber models often have a simpler design, but require caution when working with seals.
An important element is loop group. For different series Pozis (for example, RD, RK, Frio series), the location of the mounting holes and the shape of the hinges themselves may vary. On some models, the top hinge is a non-removable axle, while on others it is completely removed along with the bracket. Understanding the type of your design will help you avoid errors during assembly.
Differences between models with magnetic tape
In some older models, the seal may be glued, rather than simply inserted into the groove. In this case, additional heating with a hairdryer is required to soften the glue before dismantling, so as not to tear the rubber.
It is also worth considering the presence of additional elements on the door, such as a display, control button or bottle shelf. If your model Pozis has an electronic control module installed on the door, you will need to carefully disconnect the cable cable before rehanging it. This requires special delicacy, as the contacts may be fragile.
⚠️ Attention: On models with the No Frost system, the cold air supply channels may pass through the door hinges. When dismantling, make sure that the air ducts are not twisted and the sealing cuffs of the channels are intact, otherwise the cooling efficiency will sharply decrease.
Removing the door: step-by-step algorithm
The process of removing the door should start from the top leaf if you have a two-chamber refrigerator. This will ensure the stability of the structure, since the lower part will serve as a support. The first step is to remove all removable elements from the door: shelves, containers and decorative trims. This will significantly reduce the weight of the structure and minimize the risk of damage to fragile interior parts.
Next, you need to dismantle the top hinge. Unscrew the mounting bolts holding the bracket. At this moment the door must be held, since after removing the loop it will remain hanging only on the seal or magnets and may fall. Carefully lift the door, removing it from the lower axis, and place it in a safe place, preferably on a soft surface, so as not to scratch the front panel.
- 🚪 Remove the top decorative hinge plug (if equipped).
- 🔓 Unscrew the bolts securing the upper hinge with a wrench or a screwdriver.
- 🙌 Remove the door from the lower support axis, holding it with your second hand.
- 🔧 Remove the lower support pin or hinge for reinstallation on the other side.
After removing the upper door, go to the lower (freezer) camera). The principle of operation is similar: remove the upper hinge of the lower chamber (which is located in the middle of the refrigerator), dismantle the door. It is important not to lose washers, bushings and plastic spacers that may be located inside the hinge mechanism. Each part has its own purpose and provides the correct gap.
When dismantling, pay attention to the condition sealing rubber. If it has creases or damage, re-hanging it may be a good reason to replace it. However, if the rubber is elastic and intact, simply wipe it with a damp cloth from dust and dirt accumulated in the folds.
Table: Typical mistakes when hanging doors
Even with instructions, home craftsmen often make mistakes that lead to the door not fitting tightly or extraneous sounds. Analyzing common problems will help you avoid them during your work. Below is a table systematizing typical mistakes and methods for preventing them.
| Error | Consequence | How to avoid |
|---|---|---|
| Incomplete tightening of bolts | Door distortion, violation tightness | Use a wrench, check the tightness of all bolts |
| Loss of plastic bushings | Creak, friction of metal on metal | Put small parts in a container, do not leave them on the floor |
| Twisting of the cable (for No Frost) | Broken wires, electronics failure | Carefully lay the wires, secure with clamps |
| Ignoring the adjustment of the legs | The door does not close itself | After installation, check the tilt of the refrigerator body |
One of the common mistakes is ignoring adjusting screws on hinges. Many models Pozis provide mechanisms (fine-tuning) for the position of the door relative to the body. If after installation you notice that the door is skewed, do not rush to unscrew everything again - try using these adjusters.
Installing the door on the new side and adjusting
After successful dismantling, the installation stage on the opposite side begins. There are usually technological holes on the body of the refrigerator and at the end of the door, closed with plastic plugs. You need to move the plugs to the vacated spaces to maintain an aesthetic appearance. Then install the lower support pin or hinge in a new place using the standard holes.
Hanging the door is done in the reverse order. Place the bottom door on the axle, put on the middle hinge (for two-chamber models) and secure it. Then install the top door and mount the top bracket. At this stage, it is critical to monitor alignment of the holes. Do not use excessive force if the bolt does not fit - the door may be warped and needs to be lifted or moved a little.
- 🔄 Rearrange the decorative plugs into the vacated holes.
- 🔨 Install the support axes and hinges on a new one side.
- 🚪 Hang the doors, starting from the bottom leaf.
- 🔩 Tighten the fastening bolts, controlling the position of the doors.
The final stage is adjustment. The door should close tightly around its entire perimeter. Check this with a piece of paper: press it between the door and the body at different points. If the paper is removed with the same force along the entire perimeter, tightness is ensured. If the paper dangles loosely in some place, you need to tighten the adjusting bolts or check the evenness of the installation of the refrigerator itself.
⚠️ Attention: Technical characteristics and design of the hinges may vary depending on the year of manufacture and the specific series of the refrigerator. Always check your actions with the official user instructions included with your model Pozis.
Frequent questions and answers (FAQ)
Do you need to defrost the refrigerator before hanging the door?
Yes, this is highly advisable. First, an empty refrigerator is easier to move and tilt. Secondly, during defrosting, you can wash the internal surfaces and remove water that may spill when the body tilt changes during work.
What to do if, after rehanging, the door does not fit tightly?
First of all, check the horizontal installation of the refrigerator itself using a level. Often the problem is solved by tightening the front adjustable supports. If the body is level, try loosening the hinge mounting bolts, press the door tightly to the body and tighten the bolts again.
Is it possible for one person to hang the door on their own?
Theoretically it is possible, but it is strongly not recommended. The refrigerator door is heavy and bulky and can be easily dropped or damaged. In addition, it is difficult to hold the door and tighten the bolts at the same time. Involve an assistant for backup.
Will the warranty be lost if you re-hang it yourself?
According to the law, the consumer has the right to independently service equipment if this does not require special complex equipment. However, if during the rehanging process you damage the hinges, break the glass or damage the integrity of the wiring, the warranty case will not be recognized. Proceed carefully.
When finishing work, wipe the external surfaces of the refrigerator and check the operation of door handles and locks (if any). Correctly re-hanging the door will extend the service life of your door and make its use as convenient as possible. If you followed the instructions and were careful, the result will please you for many years. Pozis and will make using it as convenient as possible. If you followed the instructions and were careful, the results will please you for many years.