How to properly remove the LG refrigerator door: instructions with photos and nuances

Removing a refrigerator door LG is a task encountered when moving, repairing or re-hanging the hinges to change the opening direction. Despite the apparent complexity, the procedure is quite doable with your own hands, if you know key design points and avoid common mistakes. In this article we will analyze a step-by-step algorithm for models with upper and lower location of the freezer, pay attention to the tools and warn against common mistakes that can lead to damage to the seal or fasteners.

A feature of refrigerators LG is the use of modular hinge system, which differs from the classic solutions Samsung or Indesit. Here it is important to take into account door weight (up to 15–20 kg for two-chamber models) and the presence hidden latches under decorative plugs. If you plan not just to remove, but move the door to the other side, you will need additional adjustment of the hinges and leveling - we will also talk about this below.

⚠️ Warning: On models LG Instaview Door-in-Door (with a transparent insert) and refrigerators with a system Linear Cooling the dismantling process has nuances due to integrated sensors. If removed incorrectly, damage to the electronics may occur - such cases are not covered by the warranty.

Preparation: tools and safety precautions

Before you begin, make sure that the refrigerator unplugged is defrosted (if required). To dismantle the doors LG you will need:

• 🔧 Phillips screwdriver (usually PH2) - for most hinges.
• 🔨 5 mm hexagon - for models with hidden bolts (for example, LG GB-B509SLQZ).
• 📏 Level - if you plan to hang the door.
• 🧲 Magnet or tape - for fixing small parts (screws, plugs).
• 🧤 Rubber-coated gloves - so as not to scratch the surface.

Important: do not use power tools (screwdriver, drill) - there is a high risk of breaking the threads in the plastic fasteners or overtightening the bolts. hinges LG are designed for manual tightening with moderate force.

If your refrigerator is equipped with water/ice dispenser (models LRMVC2306S, LFXS26973S etc.), before removing the door be sure to:

1. Turn off the water supply.
2. Disconnect the hoses from the rear panel (an adjustable wrench will be required).
3. Drain the remaining water from the system (press the dispenser button for 10–15 seconds).

Door fastening diagram: what you need to know

Design of hinges LG depends on series and year of manufacture. Below is a table with the main types of fasteners:

For two-chamber refrigerators LG with a system DoorCooling+ (models 2020 and newer), the upper hinge of the freezer compartment is often equipped with an opening sensor - it cannot be disconnected without first disconnecting from the control board.

To determine the type of fastening of your model, inspect:

• 🔍 Decorative plugs on the hinges - bolts may be hidden under them.
• 📄 Operating instructions (section "Re-hanging doors").
• 🖥️ Official website LG - enter the model in search for spare parts.

Step-by-step instructions: how to remove the door of an LG refrigerator

Let's consider a universal algorithm using the example of a two-chamber model with an upper freezer (GB-B509SLQZ). For other series, the steps may differ slightly - follow the fastening diagram from the previous section.

Step 1: Removing the top door (freezer)

1. Open the freezer door 90°. Place a towel or cardboard under it to avoid scratching the floor.

2. Remove the decorative plug from the top hinge (if there is one under it you will see 2-3). bolt.

3. Loosen the bolts 2-3 turns, but do not unscrew it completely. This will prevent the door from falling.

4. Holding the door, unscrew the bolts completely and remove it from the hinge pin. kg.

Step 2: Removing the middle hinge (for the refrigerator compartment)

1. Close the refrigerator compartment and inspect the middle hinge. It may be hidden under the cover or control panel.

2. Unscrew the bolts securing the hinge to the refrigerator body (usually 3. pieces).

3. Carefully remove the hinge, do not pull it towards you - it may be connected to the sensor wiring.

Step 3: Removing the bottom door (refrigerator compartment)

1. Open the door 45° and fix it in this position (for example, stop).

2. Remove the lower decorative trim - the hinge bolts are hidden under it.

3. Loosen the bolts, holding the door. Unscrew them completely and remove the door from the lower pin.

⚠️ Attention: On models with Inverter Linear Compressor (for example, GA-B419) the lower hinge can be connected to the shock absorption system When dismantling, do not pull the door up - first move it 5-10 mm forward to release it. fasteners.

Nuances for Side-by-Side and French Door models

Refrigerators LG with side chambers (Side-by-Side) and models type French Door (with two doors to the fridge compartment) require a special approach:

• 🔄 Synchronous loosening of the bolts. The hinges on such models are interconnected - if you loosen the bolts on only one door, the second may warp.
• 🔌 Disconnecting the wiring. B doors French Door often there are wires for the dispenser or display. They must be carefully disconnected from the connectors on the body.
• 📐 Adjustment after rehanging. Due to the large weight of the doors (up to 20–25 kg each), after installation on the other side, precise level adjustment is required.

For models LRMVC2306S i LFXS26973S the process looks like this:

1. Remove the top panel (it is secured with latches).
2. Disconnect the wiring connectors from the control board.
3. Loosen the bolts on the top hinges of both doors at the same time.
4. Remove the doors, starting from the right (if you are looking at the refrigerator).

What to do if the door is jammed during removal?

If the door cannot be removed from hinge pin, check:

1. Are the bolts completely unscrewed (sometimes 1-2 turns of thread remain).

2. Are there any hidden fasteners (on some models they are located on the inside of the hinge).

3. Is the door skewed - try to slightly swing it left and right.

If the problem persists, do not use force - contact the service center LG.

How to move the door to the other side

If the purpose of removing the door is to change the opening side, after dismantling you will need:

1. Move the hinges to the opposite side (the holes for them are usually symmetrically located and closed with plugs).
2. Rearrange the handles (if they are removable) or rotate them 180°.
3. Adjust the position of the door aligned so that it fits snugly against the body.
4. Check the seal —after rehanging it may become deformed. If necessary, heat it with a hairdryer (temperature 50–60°C) to restore its shape.

⚠️ Attention: On models with Door-in-Door (inner door), rehanging is possible only at a service center. Independent attempts lead to a violation of the tightness of the inner chamber.

To adjust the door by level:

1. Place the level on the upper edge of the door.
2. If there is a misalignment, loosen the hinge bolts and adjust position.
3. Tighten the bolts and check the fit of the seal around the entire perimeter (use a piece of paper - it should be pressed tightly when closing).

Typical mistakes and how to avoid them

Even with careful dismantling, users often make mistakes that lead to breakdowns. Here are the most common:

• 🔩 Tightening the bolts. This deforms the threads in the plastic bushings of the hinges. Solution: tighten the bolts by hand, without force.
• 🚪 Abrupt removal of the door from the pin. May damage the latches or seal. Solution: move the door forward and then up.
• 🔌 Ignoring the wiring. On models with a display or sensors, broken wires leads to errors Er IF or Er dH. Solution: take pictures of the connectors before disconnecting.
• 🧊 Removal without defrosting. Ice in the freezer adds weight and may deform the door when removed. Solution: defrost the refrigerator 12 hours before work.

If after installing the door you notice that:

• It opens on its own —the hinges need to be adjusted vertically.
• Appeared creaking —lubricate the hinge pins with silicone grease (do not use WD-40!).
• Sealant does not fit —heat it with a hairdryer or adjust the position of the door.

When to contact the service center

Not all situations can be solved on your own. Contact a professional if:

• 🔧 Hinges or pins are deformed (for example, after a door fell).
• ⚡ The display appears errors (Er FF, Er HS) associated with sensors doors.
• 🔌 Damaged wiring in the hinge (exposed wires or melting are visible).
• 🚪 The door is not fixed in the closed position even after adjustment.

The cost of rehanging doors in service centers LG (as of 2026) ranges from 1,500 to 3,500 rubles, depending on models. During the warranty period, the service is provided free of charge, but only if re-hanging is provided for by the design (check this in the refrigerator passport).

FAQ: Frequently asked questions about removing LG refrigerator doors

Is it possible to remove the door of an LG refrigerator alone?

Technically, yes, but it is risky. Doors weigh 10–20 kg, and without an assistant there is a high chance of dropping them or damaging the hinges. For models Side-by-Side help is required - the weight of each door can exceed 20 kg.

What to do if the refrigerator does not turn on after removing the door?

Most likely, the wiring of the door opening sensor or control board is damaged. Check:

1. The condition of the connectors on the refrigerator body.
2. The integrity of the wires in the loop (they should not be pinched or torn).
3. The presence of errors on the display (code Er dH indicates a problem with door).

If the malfunction remains, call a technician.

How to remove the door if the bolts are rusty?

Do not try to unscrew them by force - this will lead to the thread breaking. Proceed as follows:

1. Apply to the bolts penetrating lubricant (for example, Liqui Moly MoS2) and wait 10-15 minutes.
2. Use impact screwdriver or a spanner with a lever.
3. If the bolt does not budge, drill it with a drill (the diameter of the drill is 0.5 mm less than the diameter of the bolt).

After dismantling, replace the rusty bolts for new ones (articles can be found in the spare parts catalogue LG).

Do you need to lubricate the hinges after removing the door?

Yes, but only silicone lubricant or with special compounds for refrigeration equipment. Do not use:

• WD-40 - it is aggressive for plastic and rubber.
• Vegetable oil - it oxidizes and contaminates the mechanism.
• Graphite grease - it attracts dust.

Apply the lubricant in a thin layer on hinge pins and rubbing surfaces.

Is it possible to hang the door on an LG refrigerator with the Instaview system?

No. Models with a transparent insert Instaview Door-in-Door (for example GR-B247JVQA) have rigidly fixed hinges and integrated ones. sensors. Self-reversing will lead to loss of tightness of the internal chamber and void the warranty. In such cases, contact an authorized service center.