Reversing the refrigerator door Samsung with a built-in display is a task that requires not only accuracy, but also knowledge of technical nuances. Unlike classic models without electronics, it is important to consider the location of the power wires for the display, sensors and system No Frost. Errors during dismantling can lead to damage to the cables or disruption of the chamber's seal.
In this article we will analyze the process step by step: from preparing tools to final adjustment of the loops. We will pay special attention to models with display on the door (series RF, RS, Family Hub), where rehanging requires working with electronic components. You will also find a tool compatibility table, warnings about common errors and answers to frequently asked questions.
If your refrigerator Samsung was released after 2018, most likely, the kit includes instructions for re-hanging the display. However, even if it is available, it is worth checking the actions with our recommendations - the manufacturer sometimes simplifies the description of the critical stages.
1. Preparation: tools and conditions
Before starting work, make sure that you have everything you need. For models Samsung with a display, you will need tools that are not in the standard set:
- 🔧 Hex key 4 mm — for fastening the hinges (included in most models).
- 🔨 Flat screwdriver — for removing decorative plugs and prying up the clips display.
- 🔧 Socket wrench 10 mm — for fastening the lower hinge (if the door is heavy, like this one Family Hub).
- 📏 Level —to check horizontality after installation.
- 🧲 Magnetic screwdriver —to avoid losing small screws when working with the display.
- 🧴 Silicone grease —for processing hinges after rehanging.
Also prepare your workspace:
- 🚪 Clear a passage at least 1.5 m wide - a door with a display weighs 15–25 kg.
- 🔌 Unplug the refrigerator 2 hours before starting work (so that the ice in the system No Frost thaws and did not damage the seal).
- 🧊 Remove all products and shelves from the door compartments - they may fall out when tilted.
Important: If your model is equipped with a system Beverage Center (water dispenser on the door), you will need an additional kit for transferring tubes. It can be ordered from an authorized dealer Samsung by part code DA97-10429A.
⚠️ Attention: In refrigerators Samsung 2020–2026 with a display Family Hub the screen power cable passes through the top loop. If dismantled incorrectly, the contacts can be damaged, which will lead to failure of the touch panel. If you are not confident in your abilities, contact the service center.
2. Dismantling the door: step-by-step instructions
Start with the top hinge - it fixes the door in a vertical position. Algorithm of actions:
Remove the decorative plug of the top hinge (pry it off with a flat screwdriver from the side.
Unscrew it). screws with a hex wrench
4 mm, but do not remove the hinge completely - it holds the door.Holding the door, carefully lift it up to remove it from the grooves of the lower hinge. Do not pull on yourself! - the display cable can tear.
Put the door on a soft surface (for example, a blanket) with the display facing up. Place wooden blocks under the corners to avoid pressure on the screen.
Now move on to the bottom hinge:
- 🔧 Unscrew the screws with a socket wrench
10 mm(in some models - a hexagon). - 🔄 Remove the hinge and set it aside - it will be needed for installation on the other side.
- 🔍 Check the mounting holes on the refrigerator body. If they are closed with plugs, carefully remove them with a flat screwdriver.
Take a photo of the location of the display cables|
Mark the top/bottom of the door with a marker (so as not to confuse it during installation)|
Check the integrity of the sealing rubber|
Prepare a container for small parts (screws, clips). hexagon).
A nuance for models with Family Hub: The display cable is attached to the door with plastic clips. To disconnect it, you need:
- Remove the display back cover (2 hexagon screws).
- Press the clips on the sides of the connector (do not pull the wires!).
- Carefully remove the cable and secure it with tape to the door so as not to bend it.
3. Transferring the hinges and preparing the holes
The refrigerator body Samsung has symmetrical holes for hinges on both sides. However, in models with a display, it may be necessary to move the fasteners for the cable.
Instructions for moving the hinges:
Take the hinges removed earlier and attach them to the mirror holes on the opposite side of the case.
Check whether the holes for the screws match. If not, use a drill with a drill
5 mm(only for metal cases!), the holes are already provided, but closed. plugs.Install the hinges in new places, but do not tighten the screws completely - first you need to align the door.
For models with Family display Hub additionally:
- 🔌 Move the fastening for the power cable (usually located in the upper corner of the door). The refrigerator comes with a plastic holder - install it on the opposite side.
- 📶 Check the length of the cable. If it does not reach the new connector, do not pull it! Contact the service to extend the wire.
| Refrigerator model | Hinge type | Do you need to drill holes? | Features of the display cable |
|---|---|---|---|
| RF23A9671SG (Family Hub) | Metal, adjustable | No (there are holes) | Cable 30 cm, secured with clips |
| RS68A8841B4 (Side-by-Side) | Plastic with metal bushings | Yes (for the bottom loop) | Cable 40 cm, connector in the upper corner |
| RB37J5230SA (with display on the door) | Combined (plastic + metal) | No | Cable 25 cm, fastener with adhesive tape |
⚠️ Attention: In refrigerators Samsung with a system Twin Cooling Plus (two compressors), when reversing the door, it may be necessary to reconfigure the temperature sensors. After installation, start the test mode through the menu Diagnostic → Door Test (instructions in the user manual).
4. Installing the door on the new side
This is the most critical step. Proceed in the following order:
Move the door to the body and align the top hinge with the groove. Make sure that the display cable is not twisted. data-i="148">Lower the door so that the lower hinge fits into the groove. Hold it by the upper edge - the weight is distributed unevenly!
Lower the door down until the bottom hinge fits into the groove. Hold it by the top edge - the weight is distributed unevenly!
Tighten the screws of the upper hinge, but not all the way. Check that the door opens freely.
Adjust the lower hinge so that the door does not sag. horizontal.
For models with display:
- 🔌 Connect the cable to the new connector on the case. Make sure that the contacts match (usually there is a key recess).
- 📱 Secure the cable with clips or adhesive tape. tape (included). Don't leave it dangling!
- 🔧 Install the back cover of the display and tighten the screws.
Checking functionality:
- 🔌 Connect the refrigerator to the network.
- 📺 Make sure that the display turns on and responds to touches.
- 🧊 Check that the indicator is on No Frost (should light up 5-10 minutes after turning on).
5. Adjustment and testing
After installing the door, it is necessary to adjust its position to avoid distortions and ensure tightness. Use the following algorithm:
Check the gaps around the perimeter of the door. They should be the same (1–2 mm). If there is more gap at the top or bottom, adjust the corresponding hinge.
Open the door 90° and release. It should remain in this position (if it closes on its own, loosen the top hinge).
Check the tightness using a sheet of paper: clamp it between the door and the body. If the sheet is pulled out without effort, the seal needs to be adjusted.
For models with Family Hub display additionally:
- 📲 Calibrate the touch screen:
Settings → Screen → Calibration. - 🔊 Check the operation of the speakers (if any): turn on music through Spotify or Deezer.
In refrigerators Samsung series Bespoke (2021+) After re-hanging the door, the display settings must be reset. To do this, press and hold the Power Cooling and Fridge button simultaneously for 10 seconds.
6. Typical mistakes and how to avoid them
Even with careful work, mistakes are possible that lead to breakdowns. Here are the most common:
- 🔌 Damage to the display cable. Cause: sudden jerking of the door or twisting of the wire. Solution: Use plastic ties to secure the cable along the door.
- 🚪 Door skew. Cause: uneven tightening of the hinges. Solution: Adjust the hinges one by one, checking the level.
- ❄️ Tightness failure. Cause: deformation of the seal during dismantling. Solution: Warm the seal with a hairdryer before installation.
- 📵 The display does not turn on. Cause: incorrect connection of the cable or contact damage. Solution: Check the connector on the refrigerator body (sometimes it is covered with a protective film).
If after rehanging the refrigerator Samsung cools:
- Check whether the temperature sensors have moved (they can be attached to the door).
- Run diagnostics through the menu
Settings → Support → Self Diagnosis. - If there is an error
22E(problem with the sensor) - contact service.
⚠️ Attention: In refrigerators with the function Auto Open Door (automatic opening) after rehanging, the proximity sensor must be reconfigured. The instructions are in the user manual in the section Advanced Features.
What to do if the door does not close after rehanging?
If the door does not close tightly, the reason may be:
1) Deformed seal - try warming it with a hairdryer (temperature no higher than 60°C) and shape with your hands.
2) Skewed hinges - loosen the screws and adjust the position of the door according to the level.
3) If a foreign object gets into the groove - check the bottom hinge for debris.
If the problem cannot be solved, the magnetic one may be damaged seal insert (needs replacement).
7. Features for different Samsung series
The design of doors and displays differs depending on the series of the refrigerator. Here are the key nuances:
| Series | Weighing features | Tools |
|---|---|---|
| Family Hub (RF, RS) | The display cable passes through the top loop. Relocation of the cable fastening is required. | 4 mm hexagon, 10 mm socket wrench, screwdriver |
| Bespoke (2021+) | Modular design - the door is removed along with the display. You need to reset the settings after installation. | 3 mm hexagon, plastic puller for clips |
| Twin Cooling Plus | Temperature sensors are attached to the door. After rehanging, calibration is needed. | Hexagon 4 mm, level |
| No Frost (without display) | The process is simpler - just move the hinges and adjust the seal. | Hexagon 4 mm, screwdriver |
For models with water dispenser (RS68A8841B4 and similar):
- 💧 Relocation of water supply tubes is required. The kit must include an adapter
DA97-10429A. - 🔧 The tubes must not be bent - the bending radius is at least 5 cm.
- 🚰 After connecting, check the tightness: pour water and make sure there are no leaks.
FAQ: Frequently asked questions
Is it possible to re-hang the door of a Samsung refrigerator with a display yourself, or do you have to call a technician?
You can re-hang the door yourself if you follow the instructions and carefully handle the display cable. However, for models Family Hub i Bespoke it is recommended to have experience working with electronics. If in doubt, it is better to call a service engineer Samsungas damage to the cable can lead to expensive repairs.
What to do if the display does not work after rehanging?
First check:
- Is the cable connected to the connector on the case refrigerator (sometimes it is covered with a protective film).
- Are the contacts on the cable damaged (inspect for abrasions or tears).
- Is the back cover of the display installed correctly - it can put pressure on the cable.
If the display still does not work, try resetting settings: unplug the refrigerator for 5 minutes, then turn it on again. If this does not help, contact the service.
Is it necessary to reconfigure the temperature settings after rehanging the door?
In most cases, reconfiguration is not required, since the temperature sensors are located inside the chambers and not on the door. However, models with Twin Cooling Plus (two compressors) may require calibration. To do this:
- Start test mode through the menu
Diagnostic → Door Test. - Follow the instructions on the display (usually you need to confirm closing the door).
If the refrigerator gives an error 22E or 25E —contact support Samsung.
How long does it take to rehang a door with a display?
On average, the process takes 1.5–2.5 hours if you act carefully. Time distribution:
- Preparation and dismantling - 30-40 minutes.
- Transfer of loops and cable - 20-30 minutes.
- Installation and adjustment - 30-40 minutes.
- Testing - 10–20 minutes.
If the refrigerator is equipped with a water dispenser, add another 20–30 minutes for moving the tubes.
Is it possible to rehang the door without disconnecting the refrigerator from the network?
No! Disconnection from the network is necessary for two reasons:
- Safety: when working with metal parts there is a risk of short circuit.
- Electronics protection: a sudden power outage during cable transfer can damage the display controller.
It is recommended to turn off the refrigerator 2 hours before the start work so that the ice in the system No Frost melts and does not damage the seal during dismantling.