Re-hanging the refrigerator door Veko is a task that many owners face when moving, renovating a kitchen, or simply wanting to optimize space. Unlike models of other brands (for example Indesit or Samsung), refrigerators from the Turkish manufacturer have their own design features. The main difficulty - do not damage the seal and adjust the hinges correctly after transfer.
B In this article you will find not only step-by-step instructions with video, but also analysis of typical mistakesthat lead to door distortion or leakage. We will also dwell in detail on choice tools (spoiler: not all screwdrivers will work!) and the nuances of working with models Veko of different series - from budget Veko RCN 3300 to premium Veko Side-by-Side.
If you have never done such work, don’t worry: the process takes no more than an hour, and the savings on calling a specialist will be 1,500–3,000 rubles. The main thing is to follow the algorithm and not skip the key steps, which we will discuss below.
Why you may need to rehang the door on a Veko refrigerator
In practice, owners resort to rehanging the door for three main reasons. Firstly, change in kitchen layout: for example, if the refrigerator was moved to another corner, and now the door opens inconveniently (it rests against a wall or furniture). Secondly, wear of hinges over time they become loose and the door begins to sag. Hanging on the other side helps to evenly distribute the load.
The third reason is replacing the seal. If the rubber gasket is torn or has lost its elasticity, it is replaced, and at the same time the door is re-hung for ease of installation. By the way, in models Veko with the system No Frost the seal wears out faster due to frequent opening (on average once every 3-4 years).
- 🔧 Hinge repair - if the door creaks or does not close tightly.
- 🏡 Kitchen redevelopment - when the furniture arrangement changes.
- 🔄 Replacement of the seal - when there is a loss of tightness.
- 🛠️ Prevention - uniform distribution of the load on hinges.
Important: in Veko series refrigerators RCN and RCS with electronic control, after re-hanging, you may need to reset the settings (see the section on calibrating sensors).
Preparation: tools and materials
Before you start work, check that you have all the necessary tools. Minimum set:
- ⚒️ Phillips screwdriver (preferably magnetic so as not to lose the screws).
- 🔨 5 mm hex key (for some models Veko).
- 📏 Level (to check the evenness of installation).
- 🧲 Magnet or adhesive tape (to secure the door during operation).
- 🧴 Hinge lubricant (silicone or WD-40).
If in yours models Veko are used on hinges (for example, in series decorative plugs on hinges (for example, in series Veko Premium), prepare a flat screwdriver or a plastic pick for their removal. dismantling. marker — it’s convenient for them to mark the location of fasteners before dismantling.
Attention! Included with the refrigerator Veko there are usually spare screws and plugs for re-hanging. If they are not there, check the vegetable drawer or the back wall (there are often little things there). empty, you will have to buy additional fasteners at the service center.
Remove food and shelves from the door|Unplug the refrigerator|Prepare a work space (towel on the floor)|Check for the presence of all screws and plugs-->
Step-by-step instructions: how to rehang the door on the Veko refrigerator
The re-hanging process can be divided into 5 key stages. Let's start with dismantling the old door. Important: if your refrigerator Veko s two cameras (freezer and refrigeration), you will have to rehang both doors. separately.
Step 1. Removing the top hinge
- Open the door 90 degrees and fix it (for example, with a magnet to the body).
- Remove the decorative plug from the top hinge (pry it off with a screwdriver).
- Unscrew the screws securing the hinge to the refrigerator body (usually 2-3 pieces).
- Carefully remove the hinge and set it aside.
Step 2. Removing the door
After dismantling the upper hinge, the door will only be held on the lower hinge. Lift it up and remove it from the pin. Be careful —the door is heavy (especially in models with auto-defrost), it is better to work with an assistant.
Step 3. Transferring the hinges to the other side
On the opposite side of the case you will see technological holes for the hinges (they are closed with plugs). Remove the plugs and install the hinges in a mirror image with respect to the previous one. position. Do not confuse the upper and lower hinges —they differ in design!
Step 4. Installing the door
Place the door on the lower pin, then secure the upper hinge. Tighten the screws gradually. checking that the door does not warp. After fixing, check the gaps - they should be the same around the entire perimeter.
Step 5. Adjustment and check
Open and close the door several times If it opens independently or tight closesadjust. hinges using a hex key. In models Veko with a display (Veko Smart), after re-hanging it may be necessary calibration of the closing sensor (see instructions for the model).
⚠️ Attention! If after rehanging the refrigerator Veko starts to buzz loudly or does not turn off, check whether the refrigerant pipeline is pinched (it passes through the hinges). In this case, you need to loosen the fastenings and reinstall the door.
What to do if the door does not close tightly after rehanging?
If the seal does not fit evenly, try the following:
1. Check if the door is warped (use a level).
2. Heat the seal with a hair dryer (temperature 50–60°C) - this will restore its elasticity.
3. Adjust the hinges: loosen the screws, align the door and tighten again.
4. for Veko usually indicated in the product passport).
Features of re-hanging for different Veko models
Refrigerators Veko are divided into several series, and the re-hanging process may differ Below are the key nuances for popular lines.
| Model series | Features of re-hanging | Typical problems |
|---|---|---|
| Veko RCN (single-chamber) | Simple design, symmetrical hinges. Standard screws are suitable. | Door misalignment due to weak hinges (additional lubrication is needed). |
| Veko RCS (two-chamber) | It is necessary to re-hang both doors. The upper hinge of the freezer is secured with 4 screws. | Difficulties with leveling the freezer door (a level is needed). |
| Veko Side-by-Side | Heavy doors, two people are needed. The hinges are adjusted with a hexagon. | It is difficult to align vertically (use adjusting washers). |
| Veko Smart (with display) | After re-hanging, a reset is required (press Mode + Temp to 5 sec). |
Closing sensor error (if the door does not lock). |
In models with No Frost system (for example, Veko RCS 5200 NF) after re-hanging, cooling may temporarily deteriorate. This is normal - the refrigerator needs 12–24 hours to stabilize the temperature.
⚠️ Attention! In refrigerators Veko s inverter compressor (series Inverter) after re-hanging it is not recommended to immediately turn on food. Wait 10–15 minutes for the oil in the compressor to be distributed evenly.
Typical mistakes and how to avoid them
Even with the apparent simplicity of the process, many make mistakes that later lead to breakdowns. Here TOP-5 misses and ways to prevent them:
- 🔩 Tightening the screws → leads to thread failure. Solution: tighten crosswise, without excessive force.
- 🔄 Confusion with the upper and lower hinges → the door does not close. Solution: the hinges are marked with letters
L(left) andR(right). - 🧲 Ignoring the magnetic seal → loss of tightness. Solution: after installation, check the fit with a sheet of paper (it should hold).
- ⚡ Work under voltage → risk of electric shock. Solution: be sure to remove the plug from the socket!
- 🛠️ Lack of hinge lubrication → creaking and wear. Solution: use silicone grease (not oils!).
Another common mistake is incorrect installation of decorative plugs. If they are not secured tightly, they will fall off over time, exposing the mounting holes. In models Veko the plugs are often fastened with latches - press until you hear a click.
Video instructions: how to hang the door on a Veko refrigerator
For clarity, we have selected the best videos with a step-by-step process. Please note: the algorithm may differ slightly depending on the model, but the general scheme remains the same.
Video 1. Re-hanging the door on Veko RCN 3300 (single-chamber)
This video shows the process for a budget model. The author explains in detail how to remove the decorative trims and adjust the hinges:
https://www.youtube.com/watch?v=example_link_1 (replace with the current one).
Video 2. Transferring doors to Veko RCS 5200 (two-chamber)
The work with the freezer and refrigerator compartments is demonstrated here. Pay attention to the moment with the alignment of the top hinge:
https://www.youtube.com/watch?v=example_link_2.
Video 3. Adjusting the door after rehanging
If the door sags or does not close, this video will help fix the problem without calling masters:
https://www.youtube.com/watch?v=example_link_3.
⚠️ Attention! In some videos, the authors use non-standard tools (for example, a gas wrench instead of a hexagon). Do not repeat this - this can damage the fastenings!
What to do if after re-hanging the refrigerator does not work correctly
Sometimes after re-hanging, owners encounter problems in the operation of the refrigerator. Here are the most common symptoms and their causes:
- ❄️ The upper chamber does not freeze → the pipeline is pinched or the seal is broken.
- 🔊 Loud noise from the compressor → vibration is transmitted to the door (needs to be adjusted hinges).
- 💡 The error indicator is flashing → in models with a display, the settings are lost (reboot required).
- 🚪 The door opens itself → incorrect tilt angle (use adjusting washers).
If the refrigerator Veko after re-hanging does not turn on, check:
- Connected is it connected to the mains (sometimes the plug falls out of the socket when moving).
- Is the power cord damaged (especially if it is pressed by a door).
- Has the thermal fuse tripped (in this case, you need to wait 10-15 minutes before automatic reset).
FAQ: Frequently asked questions about rehanging the door on the Veko refrigerator
Is it possible to rehang the door on the Veko refrigerator yourself if no experience?
Yes, this is possible even for beginners. The main thing is to take your time and follow the instructions. Start by watching a video for your model, then get your tools ready and follow the steps. If you are afraid of making a mistake, practice removing/installing the top hinge without completely dismantling the door.
How much does it cost to rehang a door at the Veko service center?
The cost depends on the region and model. The average prices in Russia are as follows:
- Single-chamber refrigerator: 1,200–1,800 rubles.
- Double-chamber: 1,800–2,500 rubles.
- Side-by-Side: 2,500–3,500 rubles.
If hinges or seals need to be replaced, the price will increase by 500–1,500 rubles.
What to do if, after rehanging, the Veko refrigerator door does not close tightly?
Check first:
- Evenness of door installation (use a level).
- Condition of the seal (it may be dirty or deformed).
- Tightening of the hinges (they should be fixed firmly, but without distortion).
If the problem remains, try adjusting the hinges with a hex wrench or replace the seal.
Is it necessary to defrost the refrigerator before re-hanging the door?
Absolutely! Even if you have a model with No Frost, turn off the refrigerator 4-6 hours before work. This is necessary for:
- Safety (eliminates the risk of electric shock).
- Convenience (the door will be easier to remove).
- Safety of products (they can be temporarily transferred to a cooler bag).
Is it possible to hang the door on Veko refrigerator with display without changing the settings?
In most cases, the settings are lost, but they are easy to restore. After re-hanging:
- Connect the refrigerator to the network.
- Press the
ModeandTempbuttons for 5 seconds to reset. - Adjust the temperature again (recommended values: +4°C for the refrigerator compartment, -18°C for the freezer).
In models with Wi-Fi (for example, Veko Smart Pro), you may need to reconnect to the network.