A new refrigerator Atlant is not just a purchase, but an investment in the comfort and safety of food for years to come. But in order for the equipment to serve for a long time and without failures, the first start-up must take place according to strict rules. Many users are in a hurry to connect the unit immediately after delivery, not taking into account that incorrect start it can lead to compressor breakdowns, freon leakage or incorrect operation of electronic modules. This is especially true for models Atlant with a system No Frost or inverter compressors, where violation of the instructions can result in costly repairs.
This article contains detailed step-by-step instructions on how to properly turn on the refrigerator Atlant after purchase, taking into account the manufacturer’s recommendations and the experience of service centers. We will look at why you cannot ignore settling timehow to check the tightness of the seals, what settings to choose for the optimal mode and what to do if the refrigerator does not cool after the first start. And also typical mistakes that reduce the service life of equipment by 30-40%.
Why you can’t turn on the Atlant refrigerator immediately after delivery
The main mistake of 80% of buyers is trying to turn on the refrigerator Atlant to the network immediately after it was brought from the store. The manufacturer categorically prohibits doing this, and here's why:
- 🔹 Oil in the compressor. During transport, oil drains from the compressor into the cooling circuit. If you turn on the refrigerator immediately, the compressor will run dry, which will lead to it instant wear or jamming (repairs will cost 50-70% of the cost of a new unit).
- 🔹 Freon pressure. In refrigeration systems with
R600a(used in most models Atlant), freon is under pressure. A sudden switch on can cause water hammer and rupture of capillary tubes. - 🔹 Condensation on electronic boards. If the refrigerator was delivered in cold weather, condensation will form on the control chips. Connection to the network will lead to a short circuit.
The manufacturer Atlant indicates in the instructions the minimum settling time - 4-6 hours at room temperature. However, this parameter depends on: 4-6 hours data-i="75">🔋 Type of compressor (inverter models, for example
- 🌡️ Indoor temperatures (if below +15°C, the time increases to 8-12 hours).
- 🚛 Tilt angle during transportation (if the refrigerator was transported lying down, you will have to wait up to 24 hours).
- 🔋 Type of compressor (inverter models, for example, Atlant XM 6025-101, require longer stabilization).
⚠️ Attention: If the refrigerator was delivered in a horizontal position (lying down), be sure to check the integrity of the cooling tubes before turning it on. To do this, gently shake the unit - you should not hear liquid pouring or rattling. If you suspect damage to do not turn on refrigerator, call a technician.
Preparing the Atlant refrigerator for the first time: step-by-step checklist
Before connecting the refrigerator Atlant to the network, complete the required preparatory steps. Skipping even one step can lead to malfunctions or an increase in energy consumption by 15-20%.
Unpack the refrigerator and remove all protective films|Check the integrity of the door seals|Place the refrigerator on a flat surface (use a level)|Adjust the legs for stability|Wipe the interior surfaces with a weak solution of soda|Check the voltage at the outlet (there should be 220-230 V)|Make sure that the back wall does not touch the wall (at least 5 cm gap)
-->
Pay special attention installation of the refrigerator according to level. A misalignment of even 1-2 degrees leads to:
- 🔊 Increased noise during compressor operation.
- ❄️ Uneven distribution of cold (there will be ice in one corner, above-zero temperature in the other).
- 💧 Accumulation of water under the vegetable drawers.
To check, use a building level, placing it on the top lid of the refrigerator. Adjust the legs with the key (included) until the bubble is exactly in the center. For models Atlant with a system No Frost (for example, Atlant MXM 2835-90), the permissible slope should not exceed 0.5 degrees.
⚠️ Attention: If your model Atlant has a functionSuper FreezeorFast Cool, before turning them on for the first time, disable them through the control panel. Activating these modes on the first day of operation may cause overload of the compressor.
How to properly turn on the Atlant refrigerator: step by step
When preparation is completed, proceed to turn it on. Follow the instructions strictly in order - this will guarantee the correct operation of all systems.
Connecting to the network. Insert the plug into a grounded outlet. Make sure the voltage is stable (use a multimeter or a special tester to check). Refrigerators Atlant are sensitive to power surges - if your network has frequent fluctuations, connect a stabilizer.
Start the compressor. Press the power button (in models with electronic control) or turn the thermostat to position "1" or "2" (in mechanical ones). The compressor should start within 1-2 minutes. If after 5 minutes of operation you do not hear a slight hum, check the connection or contact service.
Temperature setting. Optimal values for the first start:
- 🥶 Refrigerator compartment: +4°C (thermostat position "3" or "Medium").
- ❄️ Freezer compartment: -18°C (position "***").
In models with a display (for example Atlant MX 2835-80), configure the parameters through the menu Temp → Fridge/MFreezer.
Checking operation. Via 2-3 hours after switching on, check:
- 🔊 No extraneous noise (knocking, grinding, vibration).
- 💨 Uniform distribution of cold (use a thermometer).
- 💧 Absence of a puddle under the refrigerator (indicates a freon leak or a clogged drainage system).
If the refrigerator Atlant is equipped with a system Smart Diagnosis (for example, series models New Line), after the first turn on, wait until the self-diagnosis is completed. The display will show a code 00 or OK —this means that all systems are working normally. If other codes appear (for example, E1, E4), contact the service center.
How long should the Atlant refrigerator work after the first turn on
Many users worry when a new refrigerator Atlant works without stopping in the first hours. This is a normal process, but there are nuances that you need to know.
| Operation period | Normal behavior | Signs of malfunction |
|---|---|---|
| First 2-4 hours | The compressor is working continuously, there may be a slight smell of plastic (dissipates after a day). | Strong heating of the side walls (above +45°C), loud knocking or vibration. |
| 4-8 hours | The compressor turns off for 10-15 minutes every 30-40 minutes of operation. | The compressor does not turn off at all or works for less than 5 minutes per cycle. |
| Days after switching on | The temperature in the chambers has stabilized, the compressor operates in normal mode (20-30 min cycle). | Temperature in the refrigeration room chamber above +6°C, in the freezer - above -12°C. |
| 3-5 days | The refrigerator reaches optimal mode, energy consumption is reduced by 10-15%. | The appearance of frost on the back wall (for models without No Frost) or water under the drawers. |
If the refrigerator Atlant works without stopping for more than 8 hours, check:
- 🔌 The connection is correct (the door may not be closed tightly).
- 🌡️ Temperature indoors (if above +30°C, the compressor will work longer).
- 📦 Number of loaded products (a large volume of warm products increases the cooling time).
What to do if the Atlant refrigerator does not turn off after 12 hours?
If the compressor runs continuously for more than 12 hours, do the following steps:
1. Unplug the refrigerator for 1 hour.
2. Check if there is anything blocking the door from closing (for example, seal or food).
3. Make sure that the thermostat is set to position "2" or "3" (not to maximum).
4. If the problem persists, call a technician to diagnose the thermostat or compressor.
Typical errors when turning on the Atlant refrigerator for the first time
Even minor flaws at the startup stage can lead to serious damage. Here are the most common mistakes and their consequences:
- 🚫 Ignoring settling time. In 60% of cases it leads to compressor jamming in the first months of operation. The repair will cost 8,000–15,000 rubles.
- 🚫 Connection via an extension cord. Refrigerators Atlant consume up to 150-300 W at starting the compressor. Cheap extension cords cannot withstand the load, which leads to overheating of the outlet or failure of the electronics.
- 🚫 Loading products immediately after switching on. Warm foods increase the cooling time by 30-50%, which creates extra load on the compressor. It is optimal to load the refrigerator 2-3 hours after starting.
- 🚫 Installation close to the wall. The rear grille should be 5-10 cm away from the wall for normal air circulation. Otherwise, the compressor will overheat, and energy consumption will increase by 20-25%.
- 🚫 Use of aggressive detergents. To wash internal surfaces, do not use bleach or abrasive sponges - this destroys the antibacterial coating (available in models Atlant s technology
BioFresh).
Another common mistake is incorrect setting. temperature. Many people set the maximum cooling (+2°C in the refrigerator), believing that this way the products will last longer. In fact, this leads to:
- ❄️ Formation of ice on the back wall (even in models with
No Frost). - 💰 Increase in energy consumption by 10-15%.
- 🥦 Freezing of vegetables and fruits in the bottom drawers.
⚠️ Attention: If you bought a refrigerator Atlant with the function Holiday ("Vacation" mode), do not activate it in the first 3 days of operation. This function turns off the refrigerator compartment, which may disrupt the temperature stabilization process.
What to do if the Atlant refrigerator does not cool after the first turn on
If 6-8 hours after starting the refrigerator Atlant does not cool or does not work correctly, do not panic. In 70% of cases, the problem is solved without calling a technician. First check:
Power. Make sure that the plug is firmly inserted into the socket and there is voltage in the network. Try connecting another device. (for example, a table lamp) into the same socket.
Thermostat. In mechanical models, turn the temperature control to maximum and listen - you should hear a click (the compressor turns on). If there is no click, the thermostat is faulty.
Door. Check whether it closes tightly. Take a sheet of paper, insert it between the seal and the body and close the door. If the sheet pulls out easily, the seal requires replacement.
Ventilation. Make sure that the rear grille is not clogged with dust and there is air access to it. c
No Frost(for example, Atlant MY 3124-000) clogged ventilation holes leads to freezing of the evaporator.
If the refrigerator Atlant hums, but does not cool, the following are possible malfunction:
| Symptom | Possible cause | Solution |
|---|---|---|
| The compressor works, but does not cool | Freon leak or capillary blockage tubes | Call a technician for diagnostics and refueling |
| The compressor turns on for 1-2 seconds and turns off | Malfunction of the start relay | Replacement of the relay (cost 1,500–2,500 rub.) |
| The refrigerator freezes too much | The thermostat or temperature sensor is faulty | Replacement of the sensor (cost 2,000–3,500 rubles) |
| Ice forms on the back wall | Clogged drainage system or malfunction of the defrosting heating element | Cleaning the drainage or replacing the heating element |
If you cannot independently determine the cause of the malfunction, use the self-diagnosis function (if your model has it):
- Press and hold. button
Super(orAlarm) for 5 seconds. - The display will show an error code (for example,
E1- a problem with the refrigerator compartment sensor). - Check the code with the table in the instructions or on website Atlant.
How to care for the Atlant refrigerator after the first turn on.
Proper care in the first weeks of operation extends the life of the refrigerator Atlant by 20-30%. Follow these recommendations:
- 🧼 Cleaning. Once a month, wash the internal surfaces with a warm soda solution (1 tablespoon per 1 liter of water). antibacterial wipes.
BioFreshuse special antibacterial wipes. - ❄️ Defrosting. Refrigerators with
No Frostdo not require manual defrosting, but once a year they need to be turned off to clean the ventilation holes. In conventional models, defrost when the ice thickness is more than 5 mm. - 🔌 Power supply. When leaving for a long time (more than 2 weeks), unplug the refrigerator, but leave the door ajar for ventilation.
- 📦 Distribution of products. Do not put warm dishes in the refrigerator (cool them to room temperature temperature). Do not fill the back wall with products - this interferes with air circulation.
For models Atlant with a display (for example, Atlant MXM 2835-90) regularly check the temperature readings if they are outside the normal range (+3...+5°C). refrigerator, -16...-20°C in the freezer), perform calibration:
- Press the button
Tempfor 3 seconds. - Use the "+" and "-" buttons to set the correct values.
- Save the settings with the button
OK.
⚠️ Attention: If your refrigerator Atlant is equipped with a function Eco Modeactivate it 1-2 weeks after the first start. This mode reduces energy consumption by 10%, but increases the operating time of the compressor. Do not turn it on if the room temperature is higher. +28°C.
FAQ: Frequently asked questions about turning on the Atlant refrigerator for the first time
Is it possible to turn on the Atlant refrigerator through an extension cord?
No, this is strictly prohibited. Refrigerators Atlant have a high inrush current (3-5 times higher than the rated current), which can melt the contacts of the extension cord. Use only a grounded outlet located no further than 1.5 m from the refrigerator. If the outlet is far away, draw a separate line.
How long should the compressor run when first turned on?
In the first 2-4 hours, the compressor works continuously, then the cycle should stabilize: 20-30 minutes of operation and 10-15 minutes of rest. If after 8 hours the compressor does not turn off, check the tightness of the door closure and the room temperature. If the problem persists, call a technician.
Do you need to wash the Atlant refrigerator before turning it on for the first time?
Yes, definitely. There may be particles of packaging materials, dust or technical grease left inside. Use a soft sponge and a warm soda solution (1 tablespoon per 1 liter of water). Do not use detergents with chlorine or abrasive cleaning powders - they damage the interior coating.
What to do if the Atlant refrigerator is severely damaged after turning it on. is it noisy?
On the first day of work, noise up to 45 dB (comparable to a quiet conversation) is normal. But if you hear knocking, grinding or vibration:
- Check that the refrigerator is level (use a level).
- Make sure that the back wall does not touch furniture or the wall.
- If the noise does not go away after 2-3 days, the compressor or fan may be faulty (in models c
No Frost).
Is it possible to place the Atlant refrigerator next to a radiator or stove?
No. The minimum distance to heat sources is 50 cm. If another placement option is not possible, install a heat-reflecting screen (for example, made of foil polyethylene foam). Remember that for every degree above +25°C in the room the energy consumption of the refrigerator is increased. increases by 5-7%.