How to properly turn on the Stinol refrigerator: instructions with photos and expert advice

The first turn on of the refrigerator Stinol is an important stage on which the durability of the equipment and the quality of cooling of products depend. Many users make mistakes already at the unpacking stage: they ignore the settling time after transportation, install the legs incorrectly, or connect the power without checking the voltage. The result is increased noise, unstable temperature, or even compressor breakdown.

This article will help you avoid typical problems. We will analyze step-by-step algorithm for all popular models (Stinol 100/101/103/107/110/116), indicate critical nuances (for example, why you can’t turn on the refrigerator while lying on your side), and give a checklist to check the functionality. We will pay special attention to setting the temperature - this parameter often gets lost at the first start.

If your Stinol has already been standing for several days after delivery, but is not cooling, do not rush to call a technician. In 80% of cases, the problem is solved by adjusting the position or resetting the settings. Read about all this below.

1. Preparing the refrigerator for the first time

Before connecting Stinol to the network, do mandatory preparatory steps. Ignoring them can lead to compressor failure or freon leakage.

✅ Settling time after transportation:

• 📦 If the refrigerator was transported vertically —wait 2–4 hours before turning on. This is necessary so that the oil in the compressor flows downwards.
• 🚛 If transported lying on your side - stand 6–12 hours (for models with the system No Frost —up to 24 hours). Otherwise, you risk jamming the compressor.
• ❄️ In winter (at temperatures below +5°C), the settling time is increased to days - this prevents condensation seal.

✅ Unpacking and checking the contents:

Carefully remove the packaging film and foam. Make sure that the box contains:

• 🔧 Key for adjusting the legs (included in the kit for models Stinol 103/107).
• 📄 Warranty card and instructions (if not, download on the website Stinol according to the model).
• 🧊 Ice tray (for models with freshness zone).

⚠️ Attention: If there are dents or scratches on the body more than 0.5 mm deep - do not turn on the refrigeratorThis may indicate damage to the cooling circuit. defect and contact the store for a replacement.

2. Installing the refrigerator in place: nuances for Stinol models

The correct position of the refrigerator affects cooling uniformity i operation noise. For Stinol special requirements apply:

📏 Distance from walls and furniture:

• 🪑 Behind: minimum 5–7 cm air circulation). wear. No Frost — 10 cm.
• ☀️ From heat sources (battery, stove, window): no less 50 cm. Otherwise, the compressor will wear out.
• ⚡ From an outlet: the cord should not be tensioned. Optimally - 20–30 cm reserve.

🔧 Adjusting the legs:

An uneven floor is the main reason vibration and noise y Stinol. Adjust the legs according to the level of:

1. Place a building level on the top lid of the refrigerator.
2. Tighten the front legs with a key (clockwise - raise, counterclockwise - lower).
3. The rear legs are adjusted manually (turn counterclockwise).
4. Acceptable slope - no more 1–2° backwards (to close the door tightly).

How to check the slope without a level?

Place a glass of water halfway on the top shelf. If the water moves towards the back wall, the slope is correct. If towards the front, raise the front legs.

⚠️ Attention: If the refrigerator Stinol 101/103 is on linoleum or laminate, place rubber feet under rubber gaskets (sold in hardware stores). gaskets

3. Electrical connection: safety first

Refrigerators Stinol incorrect connection is the reason 90% compressor breakdowns in the first month of operation.

⚡ Requirements for the socket:

• 🔌 The socket must be grounded (European standard). To check, use a tester or contact an electrician.
• 📊 Network voltage: 220–240 V. If there are frequent surges in your home, install voltage stabilizer (recommended models: Resanta ASN-1000/1-Ts or Shtil R 1000).
• 🔌 Prohibited use extension cords or tees - this can lead to overheating of the contacts.

🔄 Power on order:

1. Insert the plug into the socket all the way (there should be no play).
2. Press the button power supply (if available) or turn the thermostat to position "1" (minimum).
3. Wait for the first start of the compressor (light clicking and vibration).
4. After 15–20 minutes check whether the refrigerator has started to cool (put your hand on the back wall - it should be warm).

Yes, always|No, but I plan to|No, I don’t see the need|I don’t know what it is-->

⚠️ Attention: If after turning on the refrigerator Stinol does not start, but the indicators are on, check:

• Did safety thermostat (try removing the plug and inserting it again after 5 minutes).
• Not whether fuse the plug is blown (call with a tester).

4. Temperature setting: optimal values for Stinol

Incorrectly set temperature is the reason icing, product spoilage or increased energy consumption. In models Stinol the setting depends on the type of cooling system.

❄️ Recommended modes:

🔧 How to set the temperature:

• 📉 In models with mechanical control (for example, Stinol 100) turn the knob to the desired division (usually "2-3" for +4°C).
• 🖥️ In refrigerators with electronic display (Stinol 107) press Menu → Temperature → Refrigerator compartment and set the value using the "+/-" buttons.

The door closes tightly (no gaps)|The compressor runs in cycles (turns on/off)|There is no ice on the back wall of the refrigerator compartment|The freezer cools to -18°C in 4–6 hours-->

⚠️ Attention: If the refrigerator Stinol s No Frost freezer compartment does not freeze, but the refrigerator is working - check if the mode is turned on "Vacation" (in some models it turns off the freezer).

5. First cooling: what to do in the first 24 hours

After switching on, the refrigerator Stinol needs 6–12 hoursto enter operating mode. During this time:

• ❄️ Do not load the chambers with food - an empty refrigerator will cool faster.
• 🔊 Increased noise is possible (up to 45 dB) - this is normal for a new compressor.
• 💧 In models with a drip system, condensation may appear on the rear wall - it will disappear after the temperature has stabilized.

📊 What to check in the first day:

1. After 2 hours: the compressor should start (slight vibration and a warm case at the back).
2. In 6 hours: the temperature in the refrigerator compartment should drop to +8...+10°C.
3. In 12 hours: the freezer should reach -18°C (check with a thermometer).

🧊 When can you load food:

• 🥦 Refrigerator compartment: after 4–6 hours after switching on.
• 🍦 Freezer compartment: after 12–24 hours (for deep freezing).

6. Typical mistakes when you first turn it on and how to avoid them

Even experienced users sometimes miss important details. Here TOP-5 errorsthat lead to breakdowns Stinol:

❌ Error 1: Turning on immediately after delivery

If the refrigerator was transported lying down, and you turned it on earlier than 6 hours later, the risk of the compressor jamming increases by 70%. Oil from the compressor gets into the circuit, and a hydraulic shock occurs at startup.

❌ Error 2: Incorrect installation of the legs

A skew of more than 2° leads to:

• 🔊 Increased noise (up to 50 dB).
• 🚪 Spontaneous opening of the door.
• 🧊 Uneven cooling (in the lower part of the chamber it can be 3–5°C warmer).

❌ Error 3: Connection via extension cord

Refrigerators Stinol consume up to 150–200 W in peak mode. Cheap extension cords are not designed for such a load - this is fraught fire or compressor overheating.

❌ Error 4: Loading warm food in the first hours

If you put warm food (for example, soup or just boiled eggs) in an empty refrigerator, the temperature in the chamber will rise to +15...+20°C. The compressor will work without stopping, which reduces its resource.

❌ Error 5: Ignoring error indicators

In models Stinol 107/110 codes may appear on the display:

• E1 - problem with the refrigerator compartment temperature sensor.
• E2 — malfunction of the freezer chamber sensor.
• E4 — system failure No Frost.

If the indicator blinks for more than 5 minutes - turn off the refrigerator and call a technician.

7. Features of turning on after defrosting or moving

If the refrigerator Stinol has already been in use, but was turned off (for example, for defrosting or moving), the rules for turning on are different.

❄️ After defrosting:

• 🧽 Wipe all surfaces dry (moisture may freeze and block the fan in models with No Frost).
• ⏳ Wait 30–60 minutes before turning on - this time is needed for condensation to evaporate.
• 🔄 Set the temperature regulator to "1" and gradually increase to the desired value.

🚛 After moving:

• 📦 If the refrigerator was transported vertically - just wait 2 hours.
• 🛏️ If lying —stand 12–24 hours (depending on the room temperature).
• 🔧 Check the integrity of the seal —it could have been deformed during transportation.

⚠️ Attention: If after moving the refrigerator Stinol started vibrate strongly, check:

• Are the compressor fastenings loose (relevant for models Stinol 100/101).
• Has a foreign object gotten under the body (for example, a piece of foam from packaging).

8. Frequently asked questions about switching on Stinol refrigerators

🔹 Why does the new Stinol refrigerator not turn on after connecting to the network?

The reasons may be the following:

• 🔌 The socket is faulty (check with a tester or connect another device).
• ⏳ Not the interval after transportation has been maintained (wait 6–12 hours).
• 🛠️ The compressor protection has tripped (try removing the plug and inserting it again after 5 minutes).
• 🔧 Defective thermostat (needs replacement under warranty).

If the indicators are on the panels are on, but the compressor does not start - call a technician (there may be a freon leak).

🔹 Is it possible to turn on the Stinol refrigerator at a room temperature below +10°C?

No. At temperatures below +10°C:

• The oil in the compressor thickens, which leads to to increased load.
• The seal loses elasticity, and the door may stop closing tightly.
• In models with No Frost may ice up the fan.

If you need to turn on the refrigerator in an unheated room (for example, at the dacha in winter), use heating cable for the compressor (sold in service centers).

🔹 How long should the compressor work when first turned on?

Normal:

• 🕒 First 2–3 hours the compressor can work continuously (cooling empty chambers).
• 🔄 Then it should go into cyclic mode: works for 10–15 minutes, rests for 20–30 minutes.
• ⚠️ If the compressor does not turn off longer 6 hours - this is a reason to contact the service.

🔹 What to do if, after turning on, the Stinol refrigerator makes a lot of noise?

Check:

• 📏 Installation level (adjust the legs).
• 🧊 Does the case touch the back wall or furniture (there should be a gap of 5-10 cm).
• 🔊 Is the mode turned on "Super Freeze" (in this case, the noise of the compressor reinforced).
• 🛠️ Are the compressor fastenings loose (relevant after transportation).

If the noise does not disappear after 24 hours, record it on video and contact the service center (the fan or compressor may be defective).

🔹 Is it necessary to defrost a new refrigerator Stinol before turning it on for the first time?

No, defrost a new refrigerator no need. The exception is if you bought use equipment and there is ice on the walls.

In models with No Frost (Stinol 103/107) defrosting is required once a year to clean the ventilation ducts.