How to properly remove the Stinol refrigerator door: instructions with photos and videos

Removing the refrigerator door Stinol is a task that every owner of this equipment faces sooner or later. The reasons can be different: from a banal rearrangement of furniture to replacing a seal or repairing hinges. However, without knowledge of the design features of the model and the sequence of actions, the process can turn into painful torture with the risk of damaging the equipment. This is especially true for refrigerators Stinol Soviet and early post-Soviet production (series 101, 103, 110), where door fastenings have unique engineering solutions.

In this article we will analyze the dismantling process step by step - from preparing tools to the nuances of working with different models. You will learn how to avoid common mistakes (for example, warping the door when installing it back), what parts may require replacement, and what to do if the door refuses to go back into place after removal. And for visuals, we have added links to video instructions from masters with 10 years of experience in repairing refrigeration equipment.

Preparation for dismantling: tools and safety measures

Before you start work, make sure you have what you have at hand there is everything you need. For most models Stinol (except modern ones with electronic control) you will need a minimum set:

• 🔧 Phillips screwdriver (preferably with a magnetic tip - the screws in the hinges often “stick” and fall out)
• 🔧 Flat screwdriver (for prying up decorative plugs)
• 📏 Ruler or square (to check the evenness of the door after installation)
• 🧲 Magnet (to hold small screws and washers)
• 🧴 WD-40 or equivalent (if the hinges are rusty or stuck)

Important: if your refrigerator Stinol belongs to models with top freezer compartment (for example, Stinol 104 or Stinol 116), also prepare a stepladder or a stable chair —the freezer door is removed from above, and it is inconvenient to work in weight. For models with No Frost (for example, Stinol NF 330), you will additionally need vacuum cleaner - after removing the door, dust may spill out from the ventilation ducts.

⚠️ Attention: If the refrigerator is connected to the network, be sure to unplug it from the outlet 1-2 hours before starting work. This is necessary not only for safety, but also to ensure that the compressor cools down - hot parts of the plastic case can be deformed under mechanical stress.

Also note that refrigerator doors Stinol weigh from 8 to 15 kg (depending on the model and material). Work with an assistant if you are not confident in your abilities - falling the door can damage the hinges or glass shelves inside the chamber.

Design features of Stinol doors: what you need to know before removing

Refrigerators Stinol were produced in several design series, and the method of fastening the doors in them differs. Here are the key points that affect the dismantling process:

A critical nuance for models before 2005: non-standard screws with left-hand threads are often used in the hinges (especially in the upper brackets). If The screwdriver turns, but the screw does not come out - try turning it in the opposite direction. Also in old ones Stinol there may be rivets instead of screws they will have to be drilled out.

Another “trick” of the brand is hidden seal clamps. In models Stinol 103 i Stinol 110 the door elastic is attached not only to glue, but also to plastic clips, which break when removed inaccurately. If you plan to replace the seal, buy a set of clips in advance (article for Stinol — 6000-000026).

How to determine the year of manufacture of your Stinol?

The year of manufacture of the Stinol refrigerator is encrypted in the serial number on the nameplate (usually on the back wall).

The first two digits after the letter code are the year (for example, AT98... - 1998, KL03... - 2003).

If the plate is erased, focus on the design: models before 2000 have handles in the form of “ears”, after 2005 - integrated handles.

Step-by-step instructions: how to remove the door of a Stinol refrigerator

Let's consider the universal algorithm using the example of the most common model - Stinol 103 (with an upper freezer compartment). For other series, we will clarify the nuances. separately.

Step 1: Removing the decorative plugs

On most models Stinol the hinges are closed with plastic plugs. To remove them:

1. Pry the plug with a flat screwdriver on the side. (there is a small groove there).
2. Gently pull it towards you - it should come off the latches. Do not use force so as not to break the clips!
3. If the plug is stuck, pour it around the perimeter. WD-40 and wait 5-10 minutes.

Step 2: Unscrewing the lower hinge

The lower hinge is Stinol 103 attached with two screws:

1. Unscrew top screw (it is usually longer) 3-4 turns, but do not remove it completely.
2. Unscrew bottom screw completely and pull it out.
3. Holding the door, carefully lift it up - it should come out of the groove of the lower hinge.

Important! In models Stinol 110 i Stinol 116 the lower hinge has retaining ringwhich must first be removed pliers.

Step 3: Removing the top bracket

The top bracket is Stinol 103 attached to the refrigerator body with two screws for a Phillips screwdriver:

1. Unscrew both screws (they may be hidden under the decorative trim).
2. Remove the bracket from the hinge by pulling it towards you.
3. Carefully lay the door on the floor, having previously laid a soft cloth (so as not to scratch the enamel).

For models Stinol NF (No Frost) the top hinge is often equipped plastic bushing. When dismantling, hold it with your hand - if the bushing falls out, it will be difficult to find a replacement.

Is the refrigerator disconnected from the network?|Is there an assistant to support the door?|Are the tools (screwdrivers, WD-40) prepared?|Are the hinges photographed before dismantling?|Are there a place for neatly laying the door?-->

Step 4: Removing the freezer door (for two-chamber models)

If yours is Stinol two-chamber (for example, Stinol 104 or Stinol 200), The freezer door is removed in the same way, but with nuances:

1. First remove refrigerator door (as described above).
2. Unscrew middle hingethat connects both doors.
3. Holding the freezer door, unscrew top screws (they can be hidden under a plug on the ceiling of the chamber).
4. Remove door, pulling it towards you and slightly up.

In models Stinol Side-by-Side (for example, Stinol SBS 236) the doors are removed independently of each other, but the weight of each can reach 20 kg - you can’t do without an assistant here.

Typical problems and how to solve them avoid

Even with careful dismantling, owners Stinol often encounter difficulties. Here are the most common of them and methods of solution:

• 🔧 The screws do not come out - if the thread is “stuck”, do not try to tear it off by force. Water the screw WD-40, wait 15 minutes and try again. For older models, you may need an impact screwdriver.
• 🚪 The door is stuck in the hinges - this happens if the refrigerator has been standing unevenly for a long time. Try to slightly swing the door left and right, while lifting it up.
• 🔩 The plastic bushing is broken —in models Stinol NF this is a common problem. Workaround: Wrap duct tape around the hinge to ensure a tight fit. For permanent repairs, you need an original bushing (article number 6000-000045).
• ⚠️ After installation, the door is not closes -check that the hinges are not warped. Use levelto align the door vertically.

Another typical mistake is when installing it back. This leads to deformation of the hinges and cracks in the plastic case. Tighten the screws “halfway”, and then check the movement of the door. It should open smoothly, without squeaks. hooks. tightening the screws when reinstalling. This leads to deformation of the hinges and cracks in the plastic case. Tighten the screws “half-strength” and then check the door movement. It should open smoothly, without squeaks or snags.

⚠️ Attention: In refrigerators Stinol s electronic display (models after 2010), when removing the door, the calibration of the sensors may be lost. After reinstallation, reset the settings: press and hold the button. Super Cool 10 seconds.

Replacing the seal: when and how to do it

Most often, the door is removed to replace the sealing rubber. Signs that it is time to change the seal:

• 🌡️ Refrigerator does not maintain temperature, although the compressor is working without stops.
• 💧 Ice or condensation forms on the back wall 📏 The gap between the door and the body exceeds.
• 📏 The gap between the door and the body exceeds 2–3 mm (checked with a sheet paper).
• 🦟 Seal delaminated or lost elasticity.

To replace the seal with Stinol you will need:

1. New seal (original articles: 6000-000025 for the refrigerator, 6000-000027 for the freezer).
2. Silicone sealant (for example, Moment Germent).
3. Hair dryer (to soften the old glue).

Replacement process:

1. Remove the door (as described above) and lay it on a flat surface.
2. Pry off the old one seal with a flat screwdriver and remove it. Clean the groove from any remaining glue.
3. Apply sealant to the new seal and insert it into the groove, starting from the corners.
4. Warm it up. seal with a hairdryer (temperature 50–60°C) for a better fit.
5. Reinstall the door and check the tightness with a sheet of paper.

If the new seal does not hold, use double-sided tape 3M in addition to the sealant Stinol NF the seal is attached to plastic clips -they need to be carefully removed and transferred to a new rubber band.

Reinstalling the door: how to avoid distortion

Installing the door back is often more difficult than removing it. Here is a step-by-step algorithm for models Stinol 103/110:

1. Place the door onto the top bracket, making sure that the hinge is in place. into the groove.
2. Hold the door, screw in the top screws of the bracket (not all the way!).
3. Raise the door and align the bottom groove with the hinge. Insert the bottom screw. and tighten it 2-3 turns.
4. Check the vertical level. If necessary, adjust the position of the door by loosening or tightening the screws.
5. Tighten all screws finally, starting from the bottom hinges.

For models with magnetic hinges (for example, Stinol 200+):

1. Align the magnetic latches on the door and body.
2. Latch the door in the upper position with a light press.
3. Lower the door all the way so that the lower lock is in place.

If the door is after installation opens on its own, the problem is that the hinges are skewed so that there is a gap between the door and the body. was the same around the entire perimeter (checked with a sheet of paper - it should be pulled out with the same force).

⚠️ Attention: In refrigerators Stinol s water dispenser (models Stinol DSF) when installing the door you need to connect a hose water supply. Before installation, check whether the hose is kinked - this can lead to leaks.

When it is better to call a specialist: complex cases

Despite the apparent simplicity, there are situations when you can do it yourself dismantling the door Stinol can lead to serious damage. Contact a specialist if:

• 🔧 Hinges are so rustythat the screws do not budge even after WD-40.
• ⚡ Refrigerator with electronic control (models after 2015), and you are not sure about the settings after dismantling.
• 💥 Door deformed (for example, after a fall) - it can "lead" during installation.
• 🔄 Required replacement of hinges - this requires original parts and experience working with metal.
• 🛠️ Refrigerator on guarantees —self-repair will void it.

The cost of professional dismantling/installation of a door Stinol in service centers ranges from 1,500 to 3,000 rubles (as of 2026 year). If you need to replace the hinges or seal, the price will increase to 4,000–6,000 rubles, including spare parts. However, in some cases this is cheaper than repairing after an unsuccessful attempt on your own.

For example, if during dismantling you break the thread in a hinge, replacing it will cost 2 500–4,000 rubles (depending on the model). And if you damage plastic body the door, a new one will cost 8,000–15,000 rubles.

How to find original spare parts for Stinol?

Official dealer Stinol in Russia - company POZIS. On their website there is a catalog of spare parts with a search by the serial number of the refrigerator.

Alternative - services like Zapchasti365 or All-Zap, where original and similar parts are sold.

When purchasing, check the article number - for example, a loop for Stinol 103 will not be suitable for Stinol NF 330, even if they look similar.

Video instructions and additional materials

For a visual understanding of the process, we recommend that you watch the video from experienced craftsmen:

• 🎥 Removing the Stinol 103 door —step-by-step analysis with comments.
• 🎥 Replacing the seal with Stinol NF —nuances work with No Frost models.
• 🎥 Adjusting Stinol 110 hinges —how to eliminate misalignment.

It is also useful to download the official operating instructions for your model. They can be found on the website POZIS in the "Documentation" section or on forums for repairing household appliances (for example, MasterCity or ForumHouse).

If you are looking for wiring diagrams for models Stinol (for example, for diagnosing faults after dismantling), they are posted in VKontakte communities dedicated to refrigerator repair. Search by hashtags #Stinol_repair or #refrigerator_with_your_hands.

FAQ: Frequently asked questions about removing Stinol doors

Is it possible to remove a Stinol door without unplugging the refrigerator?

Technically it is possible, but highly not recommended. Firstly, it is dangerous (risk of electric shock when working with metal parts). Secondly, vibration when unscrewing the screws can damage the compressor if it is running. Thirdly, in models with No Frost the fan can turn on at any time and interfere with operation.

How much does it weigh? refrigerator door Stinol 103?

The door of the refrigerator compartment weighs about 8–10 kg, the freezer - 10–12 kg. The weight depends on the material: in older models the doors are metal (heavier), in new ones - plastic with foam filler (lighter). data-i="336">can weigh up to Stinol Side-by-Side can weigh up to 20 kg.

What to do if the door does not close tightly after installation?

Reasons and solutions:

1. Diskewed hinges — loosen the screws and adjust the position of the door according to the level.
2. Debris getting into the seal —clean the rubber band and groove from crumbs and dust.
3. Deformation of the seal —try heating it with a hair dryer (60°C) to restore its shape.
4. Wear of hinges —replacement is required (especially important for models older than 10 years).

Where to buy original ones hinges for Stinol 110?

Original hinges for Stinol 110 can be ordered:

• From an official dealer POZIS (hinge code: 6000-000030).
• On AliExpress (search for “Stinol 110 hinge”), but the quality may vary.
• In service centers that repair refrigerators Stinol (often there are used spare parts in good condition).

The cost of a new hinge is from 800 to 1,500 rubles. When purchasing, check whether the part is suitable for your modification (for example, a hinge from Stinol 110-1 may not fit on Stinol 110-3).

Is it possible to change the Stinol door to a different-floor one (from left opening to right)?

Yes, but this requires rearrangement of the hinges and, possibly, drilling new holes. In most models Stinol the hinges are symmetrical, but:

• B Stinol 103 i Stinol 110 need to be rearranged top bracket and drill holes for the screws on the other side.
• B Stinol NF you will also need to rehang water dispenser (if any).
• You will need a seal re-gluesince it is asymmetrical.

The cost of rehanging the door in the service ranges from 2,000 to 4,000 rubles.