First turning on the built-in refrigerator Samsung is a critical stage on which the durability of the compressor and the quality of operation of the entire cooling system depend. Unlike free-standing models, built-in devices have their own specific installation and ventilation, which directly affects the initial start-up. Many users make the mistake of starting operation immediately after connecting to the network, which can lead to breakdown.
Before pressing the power button, you need to make sure that the unit has been standing in an upright position for a certain time after transportation. This is required so that the oil flows into the compressor crankcase and the refrigerant is evenly distributed throughout the system. Ignoring this rule is a common cause of failure of expensive components.
In this article we will analyze in detail all the stages of preparation, configuration and first launch of your equipment. You will learn about the nuances of working with the control panel, the features of various modes, and how to avoid common mistakes when starting. Following these recommendations will ensure stable operation of your device for many years.
Preliminary preparation and exposure after transportation
The most important step before turning on the built-in refrigerator Samsungis the correct exposure after delivery. If the equipment was transported in a horizontal position or simply tilted strongly, compressor oil could leak into the refrigerant circuit. An attempt to start the engine in this condition will result in dry operation or water hammer.
The holding time depends on the transportation conditions and the ambient temperature. In winter, this period can be extended as the oil becomes more viscous. In summer, the process of liquid spreading occurs faster, but it’s still not worth the risk.
- ⏳ If the refrigerator was transported vertically, let it stand for at least 2-3 hours.
- 🚚 When transporting horizontally, a holding time of at least 8-12 hours is required.
- 🌡️ In the cold season (below +10°C) it is better to increase the settling time to 24 hours.
It is also important to check the integrity of the packaging and the absence of visible damage to the housing or thermal insulation. Built-in models often have specific fastenings for the furniture facade, which could be damaged during careless unloading. Make sure all shipping bolts and internal shelf fasteners are removed.
⚠️ Attention: Never try to speed up the warming process of the oil using a hair dryer or heater. A sharp temperature change can damage plastic elements and seals.
Choice of installation location and ventilation requirements
Built-in appliances Samsung requires strict adherence to ventilation rules, since it is hidden in a furniture box. The heat generated by the condenser must be effectively removed, otherwise the compressor will work with overload, and electricity consumption will increase.
The gaps between the cabinet walls and the refrigerator body must comply with the requirements of the instructions. This is usually a few centimeters above and below to ensure natural air convection. If the furniture is assembled without taking these standards into account, the cooling efficiency drops sharply.
Make sure that the outlet to which the device will be connected is grounded and meets the power requirements. It is not recommended to use extension cords or tees as the compressor inrush currents may be high. It is best to have a separate connection point.
| Parameter | Minimum value | Optimal value | Consequences of violation |
|---|---|---|---|
| Gap at top | 5 cm | 10 cm | Compressor overheating |
| Gap from below (vent grille) | 3 cm | 5 cm | Insufficient inflow air |
| Distance to wall | 2 cm | 5 cm | Vibration and noise |
| Room temperature | +10°C | +25°C | Operation failure thermostat |
Primary cleaning and placement of internal elements
Before loading food, the internal space must be prepared. Factory packaging, protective films and stickers must be completely removed. Remains of tape or glue can emit an unpleasant odor, which will quickly be absorbed into the products.
Wet clean the chambers using a mild soda solution or a special household appliance cleaner. This will help eliminate the smell of new plastic and possible dust that has accumulated during storage in the warehouse. After washing, be sure to wipe all surfaces dry.
Install shelves, drawers and containers in accordance with the instructions. In models Samsung with the system No Frost it is important to correctly install the air dampers and guides so that cold air circulates evenly. Improper installation of shelves can block air flow.
☑️ Preparation for the first start
Pay special attention to the door seals. They should be clean and fit snugly all around. If the door does not close tightly, the compressor will work continuously, trying to maintain the set temperature.
Connecting to the electrical network and activating the system
After the device has been conditioned and prepared, you can proceed to the electrical connection. Insert the plug into a grounded outlet. Some models Samsung do not have a physical power button on the case, and the unit starts working immediately after power is turned on.
If the control panel has a touch button Power or On/Off, press and hold it for 3 seconds. The screen should light up and a beep will sound. At this moment, the self-diagnosis system checks the main components.
In the first minutes of operation, you may hear gurgling or hissing - this is normal, the refrigerant begins to circulate through the tubes. The compressor may work intermittently, gaining the required power.
⚠️ Attention: Do not plug in the refrigerator if you see damage to the power cord or plug. This may result in a short circuit or electric shock.
Modern inverter compressors Digital Inverter operate very quietly. The absence of a loud hum does not mean that the refrigerator is not working. Focus on the display readings and the temperature inside the chambers.
Setting temperature modes and smart functions
After turning on, you need to set the optimal temperature parameters. By default, refrigerators Samsung usually have factory settings: +3°C for the refrigerator compartment and -18°C or -20°C for the freezer.
To configure, use the control panel on the door or inside the chamber. Press the button Fridge (Refrigerator) or Freezer (Freezer) to change the value. The adjustment range is usually from +1°C to +7°C for the main compartment.
- ❄️ Mode Power Cool — accelerates the cooling of products in the refrigerator compartment.
- 🧊 Mode Power Freeze — intensive freezing in the freezer compartment.
- 🍺 Mode Cool Select+ — allows you to turn the freezer into a refrigerator or a freshness zone (depending on the model).
If your model supports control via Wi-Fi and the application SmartThings, connect the device to the network. This will allow you to remotely monitor the temperature and receive notifications of faults. To pair, follow the instructions on the screen.
Operation control and product loading
Complete cooling of the internal volume to the specified parameters takes time. For an empty refrigerator, this is usually 2-4 hours, but to achieve a stable temperature, it is better to wait 12-24 hours.
Do not load the chamber with large quantities of food at once. Thermal inertia can throw off the settings, causing the compressor to work at its limit. Start loading gradually, giving the system time to compensate for the heat introduced by the products.
Watch the first cycles of operation. If the refrigerator turns on and off too often or, conversely, does not turn off at all during the day, this may indicate a problem with the seal or temperature sensor.
⚠️ Attention: Technical characteristics and control interfaces may vary depending on the specific series and year of manufacture of the model. Always check the paper instructions that come with the kit, as manufacturers can change the software and functionality.
Frequently asked questions and solving problems when starting
Even if you strictly follow the instructions, questions may arise. Below are answers to the most common of them, which will help you make sure that the equipment is working properly.
Why does a Samsung refrigerator make strange sounds after turning on?
Gurgling, clicking and a quiet hum are normal sounds of the refrigerant and compressor operating. This is especially typical for systems No Frost. If the sound does not resemble the grinding of metal and is not accompanied by vibration, there is no need to worry.
How can you tell that the refrigerator has reached the desired temperature?
The indicator is the frequency at which the compressor turns on. When it starts to turn on less frequently and operate in shorter cycles, it means the target temperature has been reached. You can also check the feeling of cold, but it is better to use a thermometer.
Is it possible to plug in the refrigerator via an extension cord?
Manufacturers do not recommend doing this. The extension cord must be designed for powerful loads (at least 10-16 Amperes) and be grounded. Cheap extension cords can melt or cause a fire.
What to do if the display does not light up after switching on?
Check whether the plug is firmly inserted into the socket. Make sure there is power to the outlet itself. If everything is fine with the electricity, the control unit or display may be faulty - in this case, you need to call a technician.
Do you need to defrost a new refrigerator before use?
No, new models Samsung with the system No Frost do not require defrosting. Simply wash them before first use. Defrosting is only needed if the device has been idle for a long time in an unheated room.