How to replace a seal on an Ariston refrigerator: a step-by-step guide with video and expert advice

The rubber seal on the refrigerator door Ariston is not just a part, but a key element responsible for the tightness of the chamber and the energy efficiency of the device. Over time, rubber loses elasticity, cracks or deforms, which leads to constant leakage of warm air, ice formation and compressor overload. If you notice that the door does not close tightly, and ice has appeared on the walls of the freezer, most likely the problem is in the seal.

Replacing the seal on the refrigerator Ariston seems like a difficult task only at first glance. In fact, with the right approach and a minimum set of tools, you can deal with it in 1–2 hours - without calling a specialist and without unnecessary expenses. In this article we will analyze step-by-step instructions with video, tell you how to choose the right elastic band for your model, and share life hacks that will save time and nerves. You will also learn what mistakes beginners most often make and how to avoid them.

Signs of seal wear: when is it time to change the rubber?

The problem with the seal is not always obvious. Sometimes the refrigerator continues to work, but consumes more electricity or does not cool food properly. Here key symptomsthat indicate the need for replacement:

• 🔍 Visible damage: cracks, tears or peeling of rubber from the door.
• ❄️ Ice in the freezereven if the defrost mode is working properly.
• 💨 Constant “blowing in” of warm air from under the door (you can check with a sheet of paper - if it falls out easily, the seal is broken).
• 📈 Increased energy consumption without objective reasons (the compressor runs longer usual).
• 🚪 The door closes with difficulty or, conversely, it opens spontaneously.

If you observe at least 2-3 signs from the list, it’s time to change the seal. There is no point in postponing repairs: a worn rubber band increases the load on the compressor, which can lead to its breakdown. And this is already repairs in the amount of 5,000 to 15,000 rubles (depending on the model Ariston).

⚠️ Attention: On some models Ariston (for example, series Hotpoint or Margarita) the seal is attached not only to glue, but also to special grooves. If you do not take this into account when replacing, the new rubber may come off in a few days.

How to choose a seal for an Ariston refrigerator: models and analogues

The first step is to choose the right rubber band Ariston differ in:

• 📏 The size and shape of the profile (for example, for models Ariston MBA 2200 and Ariston RMBA 24 different elastic bands are used).
• 🔄 Type of fastening: on glue, in a groove or with screws.
• 🎨 Color (usually black or gray, but there are also white for designer series).

The most reliable way is to find a seal by article number of the original partIt can be found. see:

1. B refrigerator passport (section "Spare parts").
2. On old seal (usually printed in small print on the inside side).
3. On the manufacturer's website or in spare parts catalogs (for example, Ariston or Indesit, since they often use interchangeable parts).

If the original seal could not be found, you can select universal analogue. The main thing is a match:

• 📐 Length (measure the perimeter of the door, taking into account the angles).
• 🔍 Profile shape (take a cross-sectional photo of the old rubber band and compare with offers in the store).
• 🔗 Type of fastening (grooved, adhesive or combined).

Preparation for replacement: tools and safety

Before starting work, prepare everything you need:

• 🔧 Screwdriver (flat or Phillips, depending on the door fastening).
• 🔪 Clerical knife or scissors (to remove old glue).
• 🧴 Silicone sealant or special glue for rubber (if the seal is adhesive).
• 🧼 Soap solution or alcohol (for degreasing the surface).
• 📏 Ruler or tape measure (for measuring a new elastic band).
• 🔌 Hair dryer (optional, to soften the old glue).

Important: Before replacing seal unplug the refrigerator and wait until it defrosts (if there is ice). You cannot work with a wet or icy surface - the glue will not set.

⚠️ Attention: On some models Ariston (for example, Hotpoint-Ariston with a system No Frost) the door may be heavier due to the built-in water dispenser. In this case, it is better to remove the door and place it on the table - it is more convenient to work.

Unplug the refrigerator|Defreeze the chamber (if there is ice)|Remove all food from the door|Prepare tools and a new rubber band|Degrease the door surface-->

Step-by-step instructions: how to remove the old seal

Removing the worn rubber band is the most important step If you do this. Carelessly, you can damage the plastic of the door or leave parts of the old glue that will interfere with the installation of the new seal. Proceed according to the algorithm:

1. Inspect the fastening. The seal may be fixed:
   • 🔗 In groove (more often). total for models Ariston middle and premium segment).
   • 🧩 On glue (budget models or old refrigerators).
   • 🔩 On screws (rarely, usually in combination with glue).

Carefully pry up the rubber band start from the corner - it’s easier. If the seal sits on glue, heat it with a hairdryer (temperature no higher). 60°C, so as not to damage the plastic).

Remove any remaining glue with solvent or alcohol. Do not use acetone - it can corrode the plastic of the door!

Check the groove (if the fastening is grooved). It should be clean and intact. If damaged, you can restore it using silicone sealant.

At this stage, many make a mistake: they try tear off the elastic with a jerkThis can break the plastic guides or leave parts of the seal in the groove. times.

What to do if the seal is glued tightly?

If the elastic does not give in even after heating with a hairdryer, try the following method:

1. Apply to the seam glue solvent (for example, Cosmofen).

2. Wait 10-15 minutes.

3. Carefully pry off the seal with the blunt side of a knife.

4. Repeat the procedure for difficult areas.

Do not use metal brushes or sandpaper - they scratch the plastic!

Installing a new seal: step by step with nuances

Now we move on to installation. It is important to follow the sequence and not rush. Let's consider two fastening options:

1. Groove fastening (the most common type for Ariston)

1. Start from the top corner. Insert the first section of the elastic into the groove (usually there is a mark or arrow indicating the direction).
2. Stretch the seal the perimeter, gradually pressing it into the groove. Do not tighten too much - the rubber should lie freely, without folds.
3. In the corners You can cut the elastic a little at 45° so that it lies more evenly. But do not overdo it - strong cuts will lead to tears.
4. Check the tightness: run your finger along the entire perimeter. If the seal falls out of the groove, fix it with glue or sealant.

2. door with a thin layer (for example

1. Apply glue on the door with a thin layer (for example, Moment Rubber or Soudal Fix AllDo not skimp, but do not overdo it - excess glue can stain the refrigerator.
2. Apply the sealantstarting from the top corner. Press it for 1-2 minutes so that the glue sets.
3. Secure). with masking tape for 12-24 hours (the time depends on the type of glue.
4. Remove excess glue with a damp cloth until it dries.

After installation do not close the door within 6-12 hours (for adhesive fastening This time is necessary for the glue to completely dry). has polymerized.

Checking the tightness: how to make sure everything is done correctly

Installing a new rubber band is half the battle. Now you need to check how well it performs its function. Here are 3 reliable ways:

• 📄 Test with a sheet. paper:
  1. Insert a sheet of paper between the door and the body.
  2. Close the refrigerator.
  3. Try to pull out the sheet. If it does not work the seal is good. If it falls out, the seal is installed incorrectly.
• 🔦 Checking with a flashlight:
  1. Place the switched-on flashlight inside the refrigerator.
  2. Close the door and turn off the lights in the room.
  3. If you see gaps, the rubber band is tight not tight.

⏱️ Condensation test:

1. Close the refrigerator for 1-2 hours.
2. Open and check for drops of water on the walls or seal. If there are any, the seal is broken.

If tests show problems, do not be upset. Most often it is enough:

• 🔧 Tighten the seal in problem areas (for example, add glue).
• 🔄 Reinstall the elastic band, paying attention to the corners.
• 🧴 Apply a thin layer silicone grease to the seal - this will improve the fit.

⚠️ Attention: On models Ariston with the system No Frost after replacing the seal, ice formation in the freezer may temporarily increase. This is normal - the refrigerator needs 1-2 days to stabilize. temperature.

Video instructions: replacing the seal on an Ariston refrigerator

For clarity, we have selected best videos with a step-by-step process for replacing the rubber band on refrigerators Ariston. Pay attention to the nuances that are often missed in text instructions:

• 🎥 General overview of the process (suitable for most models):
  Link to video (conditionally)

  In this The video shows all the stages - from removing the old seal to checking the tightness. Tips on working with the groove fastening are especially useful.

• 🎥 Replacing the seal on Ariston Hotpoint with the system No Frost:
• 🎥 How to deal with it glued with an elastic band (if it does not want to come off):

Tip: Watch the video at a reduced speed (0.75x) so as not to miss important details. Pay attention to how the master works with corners - this is the most difficult moment.

Common mistakes and how to make them avoid

Even with the apparent simplicity of the process, many make mistakes that lead to repeated replacement of the seal. Here TOP-5 mistakes and how to prevent them:

Error	Consequences	How to avoid
Wrong choice of seal (wrong profile or size)	The elastic does not hold, the door does not close tightly	Check the article number or take an old one sealant to the store
Using the wrong glue (for example, superglue or PVA)	The glue comes off after a few days, damaging the plastic	Use only glue for rubber or silicone sealant
The elastic tension is too strong during installation	The seal breaks in the corners or moves away from the groove	Lay the elastic without tension, make small cuts in the corners
Incomplete removal of old adhesive	The new seal lies unevenly, cracks form	Clean the surface thoroughly with a solvent and a spatula
Closing the door immediately after installation (for adhesive fastening)	The rubber moves, the glue does not have time to set	Fix the seal with tape and do not touch it for 12-24 hours

Another typical problem is uneven fit the seal around the perimeter. To avoid this, after installation, walk around the perimeter. elastic band iron through gauze (silk mode, without steam). This will help it take the correct shape.

FAQ: Answers to frequently asked questions

Is it possible to restore the old seal without buying a new one?

A temporary solution is to heat the elastic with a hairdryer (60–70°C) and stretch it so that it fits better. You can also lubricate the seal with silicone grease to restore elasticity. However, this will only help with minor problems. wear. If there are cracks or breaks - only replacement.

How much does it cost to replace the seal at a service center?

The price depends on the model of the refrigerator and the region. On average:

• Cost of work: 1,500–3,000 rubles.
• Cost of the seal: 1,000–4,000 rubles (the original is more expensive than analogues).

Independent replacement will only cost the price of the rubber band.

How often do you need to change the seal?

Service life of the original seal Ariston - 5–10 years. But it can be reduced to 3–5 years with:

• Frequent opening of the door.
• Use of aggressive detergents.
• Temperature changes (for example, if the refrigerator is standing next to stove).

Check the condition of the rubber band once a year.

What to do if, after replacing the seal, the refrigerator began to freeze worse?

Probable reasons:

• Loose fit of the rubber band (check with a test with a sheet paper).
• Damage to the groove when removing the old seal (needs to be restored with sealant).
• Wrong model of seal (does not fit the profile).

Fix the problem and give the refrigerator 24 hours to stabilize the temperature.

Can I use a seal from another refrigerator model?
Yes, if:
• It matches profile (sectional shape).
• Suitable length (can be trimmed, but no more than 10%).
• The type of fastening is the same (groove or glue).

For example, seals from Indesit or Hotpoint are often suitable for Ariston the same series.