Rehanging the Candy refrigerator door yourself: instructions with photos and life hacks

Re-hanging the door refrigerator Candy is a task that many owners face when moving, renovating a kitchen, or simply wanting to change the opening side. Despite the apparent complexity, the procedure is quite doable with your own hands if you know the key nuances. The main thing is not to rush, be patient and have the right tools. In this article we will analyze the process step by step, taking into account the features of popular models of the brand, and also warn against typical mistakes that can lead to damage to equipment.

It is important to understand that the design of refrigerator doors Candy depends from such as a freezer (upper or lower), the presence of a water dispenser and even the year of manufacture. For example, models of the series Candy CRU or Candy CSB have their own peculiarities of attaching hinges. We took these points into account and prepared universal instructions that are suitable for 90% of the brand’s household refrigerators. If your model belongs to the premium segment (for example Candy Grand Vita), check for the presence of additional door latches - their removal will require special care.

Preparation: tools and conditions

Before you start work, make sure you have everything you need. Minimum set of tools includes:

• 🔧 Phillips screwdriver (usually No. 2) - for most hinge screws.
• 🔧 Hex key (size depends on the model, most often 4 or 5 mm) - for some series Candy.
• 📏 Tape measure or ruler - to measure the gaps after rehanging.
• 🧲 Magnet or telescopic grip - will help if the screw falls into a hard-to-reach place.
• 🧴 Silicone grease - for processing hinges after installation.

Also prepare the workspace:

• 🚪 Clear the passage to the refrigerator - you will need room to maneuver the door.
• 🧊 Unplug the refrigerator and defrost (if the freezer is not No Frost).
• 📦 Remove all food and shelves from the door - they may get in the way or fall.
• 🧹 Place a soft cloth on the floor - this will protect the door covering from scratches.

⚠️ Attention: If your refrigerator Candy equipped with a system Total No Frost or an electronic display, after re-hanging it may be required resetThis is usually done by holding the button Super Cool for 5 seconds (the exact combination is indicated in the instructions for the model).

It would be a good idea to photograph the original position of the hinges and wiring (if any). This will help avoid confusion during reassembly. Pay attention to the thread direction screws - some models Candy use left-handed screws on the bottom hinge!

Step 1: Removing the old door

Start with the top hinge - it is usually easier to handle. Gently lift the door up to remove it from the bottom pin. If the door is stuck, do not use excessive force: check that all the screws are on the hinges. unscrewed. In models Candy CBI and Candy CSO the upper hinge can be secured with a hidden screw under the decorative plug - do not forget to remove it!

Dismantling algorithm:

1. Unscrew the screws of the top hinge (usually 2-3 pieces).
2. Hold the door, remove the decorative hinge cover (if any).
3. Carefully lift the door up and remove it from the lower pin.
4. Unscrew the screws bottom hinge and remove it from the body.

If the door is equipped with water dispenser (as in models Candy CRU 1642), before dismantling, disconnect the water supply hoses. To do this:

1. Turn off the water supply valve (usually located under the sink).
2. Disconnect the hose from the back panel of the refrigerator, first placing a container for residual water.
3. Remove the hose clamps on the door (a flat-head screwdriver may be required).

⚠️ Attention: In refrigerators Candy with the system Water Dispenser after re-hanging the door, it may be necessary reinstallation of the closing sensorIf after assembly the dispenser does not work, check the position of the magnetic contact on the frame.

Step 2: Transferring the hinges to the opposite side

Now you need to move the hinges to the other side of the body. It is important to take into account here symmetrical holes - in most models Candy they are already provided by the manufacturer and are closed with plugs. If there are no holes, the door is overhanging may not be possible without drilling the case, which will void the warranty.

Instructions for transferring hinges:

1. Remove the plugs on the opposite side of the case (use flat screwdriver or knife).
2. Move the upper and lower hinges to the new holes, aligning them with the marks.
3. Tighten the screws not all the way —this will allow you to adjust the position of the door later.
4. If the model contains middle loop (for example, in Candy CBCS 5185), move it too, maintaining symmetry.

Pay special attention the lower hinge — it often has adjusting bolt to align the door vertically. In models Candy with the system Multi Air Flow the lower hinge can be attached through a metal plate - do not lose it during dismantling!

What to do if there are no holes for the hinges?

In this case, re-hanging the door without drilling the body is impossible. Contact the service center Candy to assess the possibility of modification. Self-drilling can lead to damage to the refrigerant or electronics. which will make repairs extremely expensive.

Step 3: Installing the door on the new side

Before hanging the door back, check:

• 🔄 Whether all hinges are secured symmetrically relative to the original position.
• 🔧 Is there any play in the screws - they should be tightened, but not overtightened.
• 🧲 Are there magnetic seals on the new side (in some models they need to be moved manually).

Installation process:

1. Place the door onto the lower hinge pin, holding it by the top edge.
2. Lower the door down, so that the pin fits into the groove of the lower hinge.
3. Secure the upper hinge with screws, but do not tighten them completely.
4. Check how the door closes - if there is a distortion, adjust the position of the hinges.

For models with dispenser:

1. Connect the water supply hoses to the new side of the door.
2. Install the hose clamps and check the tightness of the connections.
3. Turn on the water supply and check the operation of the dispenser (you may need to bleed the system by holding the button 10-15 seconds).

Step 4: Adjustment and testing

After installing the door, you need to adjust its position to ensure a tight fit and silent operation. In refrigerators Candy adjustment is carried out through:

• 🔧 Upper hinge —responsible for horizontal alignment (if the door tilts forward/backward).
• 🔧 Bottom hinge —adjusts the vertical position (if the door sags or touches body).
• 🧲 Magnetic seal —should fit evenly around the entire perimeter.

How to adjust:

1. Check the gaps around the perimeter of the door - they should be the same (1-2 mm).
2. If the door sags, tighten the adjusting bolt on the lower hinge (clockwise - raises, counterclockwise - lowers).
3. If the door “moves” to the side, loosen the screws of the upper hinge and adjust the position.
4. Close the door and check how it fits - if the seal “bounces”, the hinges need to be tightened.

To check the tightness, use test with a sheet of paper:

1. Insert a sheet of paper between the seal and the body.
2. Close the door and try to pull it out sheet.
3. If the sheet comes out easily, the seal needs to be adjusted or replaced.

⚠️ Attention: In models with electronic control (for example, Candy Smart Touch) after rehanging the door, the calibration of the temperature sensor may be lost. If the refrigerator starts to work unstably, reset the settings according to the instructions.

Typical errors and how to avoid them

Even with careful work, you can make mistakes that will lead to incorrect operation of the refrigerator. Here are the most common:

• 🔧 Tightening the hinge screws - this deforms the thread and can lead to backlash. Tighten the screws with force, but without fanaticism.
• 🚪 Incorrect position of the seal - if it is “squeezed” between the door and the body, the tightness will be broken. The seal must lie freely!
• 💧 Water leakage after re-hanging —if you do not reconnect the dispenser hoses, water will drip inside the housing. Always check the tightness of the connections.
• 🔌 Forgetting to unplug the refrigerator from the mains is dangerous not only due to electric shock, but also damage to the electronics due to a short circuit.

Another common problem - creaking hinges after reweighing. Causes and solutions:

• 🔊 Insufficient lubrication —treat the hinges with silicone grease (not oil!).
• 🔩 Hinge skew —check the symmetry of their installation.
• 🛠️ Wear of bushings —in older models Candy plastic hinge bushings may crack. They are easy to replace with new ones (the article number is usually indicated in the instructions).

If after rehanging the refrigerator becomes make more noise, check:

• 🔄 Correctness installation door shock absorbers (if they are in the model).
• 🧲 Position magnetic contact —it can cling to the body.
• 🌡️ Fan operation (in models with No Frost) - sometimes when vibration it hits the walls.

Features for refrigerators with a freezer at the bottom

Models Candy with the bottom freezer (for example Candy CBCS 5185 or Candy CRU 1642) have their own nuances when hanging doors. The main difference is two-chamber designwhere the upper and lower doors are interconnected.

What needs to be taken into account:

• 🔄 Dismantling procedure - first the upper door is removed, then the lower one. An attempt to do the opposite will lead to jamming of the mechanism.
• 🔧 Middle hinge — in some models it is attached to latches, which are easy to break if removed carelessly.
• 🧊 Freezer seal —it thicker than that of the refrigerator compartment and requires more careful adjustment.

Algorithm for two-chamber models:

1. Remove the top door (as described earlier).
2. Unscrew the middle hinge screws and remove it.
3. Carefully lift the bottom door and remove it from the bottom pin.
4. Move all three hinges to the opposite side, maintaining the order (top → middle → bottom).
5. Install the bottom door first, then the middle hinge, and lastly, the top door.

After installation, check closing synchronicity both doors. If the bottom door closes before the top door, adjust the position of the middle hinge. In models with Full No Frost uneven closing can lead to icing of the seal.

Why may the bottom door not close?

This is often due to misalignment of the middle hinge or wear shock absorbers. In refrigerators Candy with a system Easy Close the problem may lie in a malfunction of the soft closing mechanism - it will have to be replaced.

When is it better to contact a specialist

Although overhanging the door Candy is quite is within the capabilities of most users, there are situations when it is better to trust professionals:

• 🛠️ If the refrigerator is on guarantees —self-repair will invalidate it.
• ⚡ If during dismantling you find damaged wires or contacts (relevant for models with a display).
• 🔧 If there are no holes for hinges on the opposite side, drilling the case requires experience.
• 🧊 If after rehanging the refrigerator does not freeze or gives an error (for example, E1 or E2 on the display).

The cost of professional door rehanging in service centers Candy varies from 1,500 to 3,500 rubles (for 2026), depending on the model and region. The price usually includes:

• Dismantling and installation of the door.
• Adjustment of hinges and seal.
• Checking tightness and performance.

If you decide to contact the service, make sure that the technician:

• 📋 Has experience working specifically with refrigerators Candy (some nuances of fastenings are unique to the brand).
• 🛠️ Uses original spare parts (if replacement of hinges or seals is required).
• 📄 Provides a guarantee for completed work (usually 3-6 months).

⚠️ Attention: Details of the design of refrigerators Candy may vary depending on the year of manufacture and series. For example, models before 2020 often used metal hinges, while new ones often used plastic hinges with a metal core. This affects the strength and the method of adjustment. If in doubt, check the details in the official documentation for your model.

FAQ: Frequently asked questions about reversing the door Candy

Is it possible to rehang the refrigerator door Candy without an assistant?

Technically yes, but it is extremely inconvenient. The refrigerator door weighs 10-15 kg, and holding it with one hand while tightening the screws with the other is very difficult. We recommend hiring an assistant, at least for insurance. If you work alone, use stands (for example, a chair) to temporarily fix the door.

What to do if, after hanging, the door does not close tightly?

First check:

1. The uniformity of the gaps around the perimeter (should be 1-2 mm).
2. Position of the seal - it should not be twisted or pinched.
3. Adjusting bolts on the hinges - they may need to be tightened or loosened.

If the problem persists, try heat the seal with a hairdryer (temperature 50-60°C) - this will restore its elasticity. In extreme cases, the seal will have to be replaced.

Do you need to defrost the refrigerator before hanging the door?

If your refrigerator is not equipped with a system No Frost, defrosting is required! Otherwise, when dismantling the door, ice may damage the seal or hinges. For models with No Frost it is enough to unplug the refrigerator for 1-2 hours to avoid condensation on electronic components.

How to rehang the door if the refrigerator Candy has a water dispenser?

The process is complicated by the need to reconnect the hoses. Here are the key steps:

1. Turn off the water and disconnect the hose from the rear panel.
2. Remove the hose clamps on the door (usually they are secured with latches).
3. After rehanging, connect the hoses to the new side, check for leaks.
4. Bleed the system by holding the dispenser button for 10-15 seconds to remove air.

If water does not flow after connecting, check water supply valve —it may become clogged during dismantling.

How long does it take to rehang the door?

If you have tools and an assistant, the procedure will take 1.5-2 hours. If you are doing this for the first time, reserve 3-4 hours - there may be delays for adjustments or searching for “difficult” screws. In the service center, the work takes about 1 hour, since the craftsmen use specialized tools.