Rehanging the doors on a two-chamber refrigerator Indesit: video + instructions

Reversing the doors on a two-chamber refrigerator Indesit is a task that owners face when moving, renovating a kitchen, or a banal desire to optimize space. Despite the apparent complexity, the procedure is quite doable with your own hands if you know the key nuances: from the correct dismantling of hinges to adjusting the gaps after installation. In this article you will find not only a text guide with photos, but also step-by-step video from professionals, as well as a table of tool compatibility for different models Indesit (series C 168, TN 118, DF 4180 etc.).

It is important to consider that the design of double-chamber refrigerators differs from single-chamber ones: here the doors are interconnected synchronizing mechanism, and improper dismantling can lead to distortion or breakage of the plastic fasteners. We will look at how to avoid common mistakes - from damage to the seal to incorrect installation of the top hinge, which most often causes squeaks and poor fit.

If you are looking for video instructions, scroll the page to the section "Video: hanging doors on Indesit in 15 minutes", where current videos with comments are collected masters For those who prefer text format, below are detailed step-by-step instructions with photographs of each stage.

What tools will be needed: complete list

Before starting work, prepare the tools - their absence halfway through the process can lead to hinge deformation or thread breakage if dismantled incorrectly. Here's what you'll definitely need:

• 🔧 Phillips screwdriver (PH2 size - standard for most models Indesit)
• 🔨 5 mm hexagon (for models with lower hinges on bolts)
• 📏 Ruler or square (to check gaps after installation)
• 🧲 Magnetic holder (to avoid losing small parts when removing doors)
• 🧴 Silicone grease (for processing hinges after rehanging)

For some models (for example, Indesit BIAA 13 or ITF 118) may be required 10 mm socket wrench - this depends on the type of fastening of the middle hinge. You can check the exact number and size of bolts in the table below.

⚠️ Attention: In models Indesit 2020–2023, the middle hinge can be attached to plastic latches. When dismantling, do not pull the door towards you - first press the latches on the inside!

Preparing the refrigerator for rehanging

Before removing the doors, take a few mandatory steps:

1. Unplug the refrigerator and wait until it defrosts (if the freezer is covered with ice. This will prevent short circuits when working with metal tools.
2. Remove all products and the shelves from the doors - they may fall when removed.
3. Seal the sealing tape rubber band with masking tape so as not to damage it when moving the doors.
4. Prepare the work space: place a soft cloth on the floor so as not to scratch the body when laying the doors.

Pay special attention synchronizing mechanism (to the bar between the doors Indesit it's often attached to the top hinge - if you don't unclip it before removing it, you can break the plastic holders.

Take a photograph of the location of the hinges and bolts|

Prepare a box for small parts|

Check the presence of all tools|

Mark the top and bottom of the doors with a marker (so as not to confuse them when installing them back)-->

Step-by-step instructions: how to remove the doors

The process of dismantling doors on two-chamber refrigerators Indesit consists of 5 key steps. Follow them strictly in order to avoid distortion or damage to the hinges.

1. Removing the top door (refrigerator compartment)

Start with the top hinge:

1. Open the refrigerator door to 90 degrees.
2. Remove the decorative plug from the hinge (pry it off with a flat-head screwdriver).
3. Unscrew the bolts with a Phillips screwdriver counterclockwise arrows (usually 2-3 bolts).
4. Holding the door, carefully remove it from the hinge pin and place it on the prepared surface.

2. Detaching the synchronizer

The synchronizing mechanism (bar between the doors) is attached to the top hinge. To remove it:

• 🔧 Unscrew the fixing bolt (usually one, located on the side).
• 🖇️ Disconnect the bar from the loop by pulling it up.
• ⚠️ Do not pull with force - if the mechanism does not give in, check whether it has gone unnoticed bolt.

3. Removing the lower door (freezer)

The lower door is removed in the same way as the upper one, but there is a nuance: often the lower hinge is attached to the an additional bolt from the inside. sides casing. To unscrew it:

1. Remove the bottom cover of the refrigerator (it is held on by latches).
2. Find the bolt under the hinge and unscrew it with a hexagon.
3. Remove the door from the pin, holding it by the bottom edge.

What to do, if the door cannot be removed?

If the door is “jammed” on the hinge pin, do not try to pull it! Most likely, the problem is in the deformed plastic bushing. Gently shake the door left and right, while pulling up. If this does not help, remove the hinge completely (unscrewing all the bolts) and remove the door along with it. data-i="140">Installing the doors on the opposite side

Installing doors on the opposite side

Now that the doors are removed, you need to move the hinges to the other side. The main thing here is do not confuse the top and bottom, since the hinges are asymmetrical. Follow the algorithm:

1. Transfer loops

• 🔧 Unscrew the hinges on the opposite side of the case (they are closed with plugs).
• 📍 Transfer them to the vacated holes, observing the order: top hinge - on top, bottom - from below.
• ⚠️ In models Indesit BIAA 13 and ITF 118 the middle loop is attached to 3 bolts —do not miss the bottom one!

2. Installing doors

Start with the bottom door (freezer):

1. Place the door on the pin of the bottom hinge, making sure that it is seated all the way.
2. Tighten the bolts, but not all the way - leave some play adjustments.
3. Install the upper door, connecting it to the synchronizer.
4. Secure the upper hinge and check that the doors open smoothly, without squeaks.

3. Adjusting the gaps

After installation, check:

• 📏 The gap between the doors —should be 2–3 mm (checked with a ruler).
• 🔄 Smooth running —the doors should open without effort.
• 🧲 Sealant fit —if gaps remain, tighten the bolts hinges.

Video: rehanging doors on Indesit in 15 minutes

For clarity, we have selected the best video instructions from the masters, which show the process on popular models. Indesit. Pay attention to the following points:

• 🎥 0:45 —how to properly remove the decorative plug without scratches.
• 🎥 4:20 —the nuances of working with the synchronizing mechanism.
• 🎥 8:10 —adjusting the hinges after installation.

📌 Video 1: Hanging the doors by Indesit C 168 (classic scheme with 3 loops)

📌 Video 2: Features of models with hidden loops (Indesit BIAA 13)

⚠️ Attention: The video may models with outdated hinge fastening (until 2019) are shown. If your refrigerator is newer, check the instructions above - the number of bolts may have changed!

Typical mistakes and how to avoid them

Even If you carefully follow the instructions, you can make mistakes that will lead to creaks, distortion or poor fit of the doors. Here are the most common ones:

• 🔧 Overtightened hinge bolts → the door opens with force. Solution: loosen the bolts on half a turn.
• 🚪 Mismatch of holes for hinges → the door hangs crookedly. Solution: check if you have mixed up the upper and lower hinges.
• 🧊 The seal is damaged → the refrigerator does not keep cold. Solution: heat the elastic with a hairdryer (temperature 50–60°C) and restore its shape.
• 🔄 Creak when opening → insufficient lubrication. Solution: Apply silicone grease to the hinge pins.

If after rehanging the refrigerator becomes makes more noisecheck:

1. Tension of the synchronizing mechanism - it should not sag.
2. Are the bolts secured to the rear wall of the case (sometimes they loosen due to vibration).
3. Does the door touch the case when closing (there should be a gap of 1-2 mm).

Frequently asked questions about hanging Indesit doors

Is it possible to hang the doors on an Indesit refrigerator yourself if you have no experience?

Yes, the procedure does not require professional skills, but the main thing is not to rush and follow the instructions. If in doubt, practice. removing/installing one door (for example, a refrigerator) before re-hanging both.

How long does re-hanging take?

On average - from 30 minutes to 1.5 hours, depending on the model, it takes the longest to adjust the gaps and check the tightness. If the refrigerator has not been defrosted in advance, add 2-3 hours. defrosting.

Do you need to lubricate the hinges after rehanging?

Be sure to use silicone grease (not petroleum-based oils - they damage the plastic) Apply 1-2 drops to the hinge pins and spread while opening/closing the door.

What to do if, after rehanging, the door does not close tightly?

The reasons may be different:

• Hinges are skewed - loosen the bolts and adjust the position.
• Deformed seal - warm it with a hairdryer or replace it.
• If debris gets into the mechanism - clean the hinges with a brush.

If the problem persists, check if something is preventing the closure (for example, a protruding shelf or a magnetic holder).

Is it possible to hang the doors on the refrigerator? Indesit with a display?

Yes, but there is a nuance: in models with electronic control (Indesit ITF 118 W, DF 5201 W), you will have to reconfigure the door opening sensorAfter re-hanging:

1. Disconnect the refrigerator from the power supply. for 5 minutes.
2. Turn on and hold the button Super Cool 10 seconds to reset the settings.
3. Check whether the backlight and open door signal work correctly.