Owners of refrigeration equipment are often faced with a situation where water appears inside the chamber or on the floor next to the equipment. In models with a system No Frost or static cooling, condensate should be discharged automatically, without requiring user intervention. However, if you notice a puddle under the door or on the floor, this is a signal of a problem with the drainage system. Understanding where exactly the moisture is directed is the first step to solving the problem without calling a specialist.
In the brand's refrigerators Beko liquid removal is implemented according to a classic scheme that has been tested for decades. The moisture formed on the back wall flows into a special chute, from where it goes through a tube into a container located above the compressor. There it evaporates safely. If this process is disrupted, the water begins to look for a way out, creating discomfort and the risk of damage to the floor covering. In this article we will analyze in detail the path of a drop from the wall to the evaporator.
The moisture removal system in refrigerators Beko is designed to minimize the need for maintenance. However, the physical properties of water and air mean that contaminants can accumulate in the channel. Drain hole is a bottleneck that most often causes a malfunction. Knowing its exact location and operating principle will help you quickly remove the blockage and return the equipment to normal operation.
The principle of operation of the condensate drainage system
The basis of the operation of the refrigeration chamber is a cyclic change in temperature. When the compressor is running, the back wall cools and moisture from the air settles on it in the form of frost or droplets. In models with drip system (or in the Fresh Zone in No Frost), when the compressor is turned off, the wall heats up. The ice melts, and the resulting water rushes down under the influence of gravity.
It is at this moment that drainage chute, located at the bottom of the rear panel, comes into operation. It collects the flowing liquid and directs it into the opening of the tube. The diameter of this channel is usually from 5 to 10 millimeters, which is enough for the free flow of water, but not enough for the passage of large particles of debris. Next, the water, through a hose running inside the housing, enters the tray above the motor.
It is important to understand that in refrigerators Beko with a system No Frost the process of moisture removal occurs automatically during defrost cycles. The water drips onto the heating element or warm tray, where it instantly turns into steam. If you see water inside the chamber, it means that the system cannot cope with the volume of moisture or the path is blocked.
⚠️ Attention: If water flows along the front panel or drips from a shelf, this often indicates that the drainage hole is frozen or clogged, and the water has nowhere to go except over the edge of the gutter.
Where is the drainage hole in Beko models
Finding the water outlet point is a simple task if you know where to look. In most refrigerators Beko, regardless of the height and number of chambers, the drainage hole is located on the back wall of the main refrigerator compartment. It is located at the very bottom, in the center or offset, right above the plastic groove, which visually resembles a small funnel.
You don’t need to disassemble the refrigerator to find it. It is enough to open the door of the main chamber and look down. You will see a horizontal slit or circular hole in the plastic. This is where the water should go. In some models of the series NeoFrost access to it may be slightly hampered by the bottom shelf or vegetable drawer, which will have to be temporarily removed.
In the freezer compartment of the system No Frost the situation is different. There the hole is hidden behind the back panel and is not directly accessible without removing the plastic. Water flows from there through internal channels. If the problem with water occurs in the freezer and you see ice near the door, the internal drainage is most likely clogged or the seal is broken.
The location of the hole was not chosen at random. This is the lowest point of the inner chamber, which ensures that all moisture drains there. If you tilt the refrigerator forward, water should still flow into this channel. The design Beko provides for a slight slope of the rear wall just for this purpose.
Why the water does not drain: the main causes of blockage
The most common reason for the appearance of water is a banal clogging. During operation, microparticles of food, crumbs, and lint from packaging get into the refrigerator. Over time, they accumulate in the drainage channel, forming a plug. Water stops passing through it and begins to overflow over the edge of the gutter directly onto the shelves and products.
The second reason is formation ice blockage. If the refrigerator is overloaded or the thermostat is faulty, the water in the duct may freeze faster than it can drain. Ice blocks the narrow opening, and new condensation simply cannot pass further. This often happens in winter or when doors are opened frequently.
- 🥦 Food remains: crumbs, pieces of lettuce or sausage casings often become the core of a blockage.
- 🧊 Ice crust: occurs due to a violation of the temperature regime or frequent opening of doors.
- 🦠 Mold and mucus: biological organisms love a moist environment and can completely clog the tube.
Mechanical damage is also worth mentioning. If you carelessly moved drawers or cleaned the refrigerator with sharp objects, you could damage the gutter itself or dislodge the tube. In the models Beko the plastic is quite durable, but fragile in the cold. Any crack will cause water to flow past the hole, into the cabinet or onto the floor.
The myth about tilting
There is an opinion that if you tilt the refrigerator, water will flow better. This is wrong. Tilt helps only if the tube inside the housing is bent or has a complex terrain, but most often the problem is at the entry point.
Instructions for cleaning the drain with your own hands
Removing a blockage is a procedure that does not require special skills, but does require accuracy. Before starting work, be sure to unplug the refrigerator. This is a safety measure, since you will be working with water and metal objects near electrical components, albeit indirectly.
First, empty the bottom of the refrigerator compartment. Remove crisper drawers and shelves if they interfere with access to the back wall. Wipe the area around the drain hole thoroughly with a dry cloth to remove any visible water or dirt. This will allow you to see the process and not spread the dirt deeper.
☑️ Preparing for cleaning
Now we proceed to mechanical cleaning. Use a special pipe cleaner (often included) or twist some soft wire/take a long bottle brush. Carefully, without sudden movements, insert the tool into the hole. Your task is to push the plug down towards the compressor. Do not use excessive force to avoid piercing the tube through.
After mechanical impact, it is recommended to rinse the channel. Fill a syringe without a needle or a rubber bulb with warm water. Squirt water into the hole. If the water leaves with a characteristic gurgling sound and does not pour back out, congratulations, the system is free. If the water is standing, repeat the procedure with a brush.
| Tool | Purpose | Precautions |
|---|---|---|
| Pipe brush | Removing soft plugs | Do not press hard so as not to scratch the plastic |
| Syringe (20 ml) | Washing with water | Water should be warm, but not boiling water |
| Vacuum cleaner | Pumping out dirt | Use only in blowing mode or gently suction |
| Soda and vinegar | Dissolving fat | Be sure to rinse after use |
If plain water does not help, you can use a soda solution. Dilute a teaspoon in a glass of warm water and rinse the canal. This will help break down fatty deposits that are often found in refrigerators where open food is stored. After the procedure, be sure to wipe the camera dry.
⚠️ Attention: It is strictly forbidden to use sharp metal objects (knitting needles, scissors, screwdrivers) for cleaning. You can pierce the drainage tube, which is located inside the wall, and then repairs will require disassembling the case.
What to do if water flows under the refrigerator
The situation when water is found on the floor under the refrigerator Bekocan have several reasons. If the internal cleanliness of the chamber is in order and it is dry inside, but there is a puddle under the equipment, the problem may lie in the water drainage system from the compressor. Water from the tray above the motor may overflow if it does not have time to evaporate.
This often happens if the refrigerator is too close to the wall or in a niche with poor ventilation. The compressor overheats and the water does not have time to evaporate, accumulating in the pan. Check the gap between the back of the refrigerator and the wall. It must be at least 5-7 centimeters for free air circulation.
Another reason is the displacement or skew of the refrigerator itself. If the equipment is not level, the water in the tray may overflow one of the sides and drip onto the floor. Use a spirit level to check the position of the frame. Adjusting the legs will help correct the situation.
It is also worth checking the integrity of the drainage tube that fits the tray. If it comes off or cracks (which happens when the compressor vibrates), water will flow past the container. To check this, you will need to move the refrigerator and remove the rear metal panel (crankcase).
Preventing the formation of blockages and ice
So that the question “where does the water flow” does not bother you in the future, you should adhere to simple operating rules. Regular cleaning is the key to a long life of the drainage system. Once every 2-3 months, it is recommended to carry out preventive flushing of the hole with warm water, even if there are no visible problems.
Keep an eye on the packaging of the products. Store opened foods (especially liquid, greasy, or crumbly foods) in closed containers. This will prevent debris from entering the chamber and, as a result, the drainage. In models Beko with zoo Active Fresh it is especially important not to block the ventilation holes with drawers.
- 🧹 Wipe the back wall with a dry cloth during each general cleaning.
- 🌡️ Monitor the temperature conditions, do not Set the values too low unless necessary.
- 🚪 Minimize the time the doors are open to reduce the flow of moist air.
If you notice that too much ice is forming on the back wall, check the door seal. A loosely closed door is the main enemy of a moisture removal system. The seal must be clean and flexible. If necessary, it can be washed with warm water and soap or replaced.
The secret of cleanliness
Put an activated carbon tablet or a special odor absorber in the refrigerator door. They also help absorb excess moisture, reducing the load on drainage.
When you need to call a specialist
Despite the simplicity of the design, there are situations when self-repair will not help. If, after thorough cleaning, water continues to accumulate inside the camera, there may be a deeper problem. This may be a malfunction Defrost heating element in the No Frost system. If the heating element is burned out, the ice does not melt, it builds up and blocks the air duct channels.
Another case is a freon leak. If there is a lack of refrigerant, the refrigerator may run non-stop, trying to gain temperature. This leads to permanent freezing of the evaporator and drainage system. In this case, simple defrosting will only give a temporary effect for a couple of days.
You also need the help of a specialist if you damage the tube while cleaning. If water flows inside the housing or you hear hissing (freon coming out), immediately turn off the device and call service. Repairing the drainage system inside the sealed case requires qualifications and special tools.
⚠️ Attention: If you smell burning or see sparking in the compressor area when trying to turn on the refrigerator after defrosting, operation of the device is prohibited until the electrician is checked by a technician.
In conclusion, the water drainage system in refrigerators Beko reliable and simple. Understanding that water flows into the gutter, passes through the tube and evaporates above the motor helps to isolate the problem. Regular care and careful storage of food will reduce the risk of leaks to a minimum.
Is it possible to pour boiling water into the drainage hole to defrost ice?
It is not recommended to use boiling water, since a sharp temperature change can damage the plastic of the gutter or the tube itself, making it brittle. It is better to use warm water (40-50 degrees) or a special defrosting spray. If there is a lot of ice, let the refrigerator stand turned off with the doors open for several hours.
Why does the water in the drainage tray above the compressor have an unpleasant odor?
An unpleasant odor indicates stagnation of water and the development of bacteria or mold. This happens if the water does not have time to completely evaporate or organic matter gets into the tray. The tray must be removed (after turning off the refrigerator), washed with a disinfectant and dried thoroughly.
How often do you need to defrost the Beko No Frost refrigerator?
The No Frost system does not require regular defrosting to remove ice, as this happens automatically. However, for hygienic purposes and to prevent blockages, it is recommended to completely defrost and wash the refrigerator at least 1-2 times a year. This will extend the life of the equipment.
What to do if the brush gets stuck in the drainage tube?
Do not pull sharply. Try gently turning the brush while pushing it back and forth. If it is stuck tightly, you can try heating the outlet of the tube with a hair dryer (at low temperature) to make the plastic softer, or pouring a little warm water to soften the plug around the brush.
Water drips only when I open the refrigerator, why?
This may indicate that water has accumulated in the groove, but does not drain due to ice plug. When you open the door, the pressure and temperature changes and the ice may melt or shift slightly, releasing accumulated water. This is a sure sign that the drainage requires cleaning.