Repairing the refrigerator handle LG: how to repair or replace it yourself

A broken refrigerator handle LG is a problem that many owners face. Even a minor crack or play can eventually lead to a complete separation of the part, and buying a new handle at a service center will cost 1,500–4,000 rubles (depending on the model). Fortunately, most faults can be fixed on your own, without the help of a specialist.

In this article we will analyze all possible causes of breakdowns refrigerator handles LG (from models GA-B489* to GR-N309*), we will show how to properly remove the door without damage, and we will give step-by-step repair instructions - from restoring plastic to replacing fasteners. You will also find out in which cases it is better not to repair the handle, but to replace it immediately, and where to buy original spare parts cheaper than in branded services.

We warn you right away: working with the refrigerator door requires care. Errors during disassembly can lead to violation of the seal tightness or damage to the hinge mechanism. If you are not confident in your abilities, it is better to turn to a professional. But if you are ready to act according to the instructions, read on!

Why the handles of LG refrigerators break: 5 main reasons

Refrigerator handles LG are made of durable plastic (usually polypropylene or ABS plastic), but even they are not eternal. Here are the most common causes of breakdowns:

• 🔨 Mechanical damage: impacts, heavy objects falling on the handle or attempts to open the door with excessive force (for example, if the refrigerator frozen and stuck seal).
• ⏳ Natural wear: over time, the plastic loses its elasticity, especially if the refrigerator is located next to heat sources (stove, radiator).
• 🔩 Loose fastenings: screws or latches inside the door become loose, the handle begins to “walk” and eventually breaks.
• 🧴 Exposure to chemicals: aggressive detergents (for example, with chlorine or acetone) destroy the top layer of plastic.
• 🔥 Temperature changes: if the refrigerator is in an unheated room (dacha, balcony), the plastic may crack.

In 70% of cases, the handle can be repaired, but there are also critical damagein which only replacement will help. For example, if the plastic has split into several parts or the fastening “ears” inside the door have completely broken off, read the following. section.

Diagnostics of damage: when the handle can be repaired and when it can only be replaced

Before undertaking repairs, inspect the handle and door of the refrigerator Here key features, which will help determine whether the part can be restored:

Pay special attention fasteners inside the door. If the screws scroll or fall out, the problem may not be in the handle, but in threaded bushings (they wear out over time). In this case, you will have to drill out the old bushings and install new ones - we will talk about this below.

⚠️ Attention: If your refrigerator LG is under warranty, do not disassemble the door yourself! data-i="114">cancellation of warranty cancellation of warranty obligations. Contact an authorized service center.

Preparation for repair: tools and materials

To repair the refrigerator handle LG you will need:

• 🔧 Tools:
• Cross and flat screwdriver (preferably with a magnetic tip)
• Hexagon (for some models, for example, LG GR-B207*)
• Pliers and wire cutters
• Drill with a thin drill (2-3 mm)
• Hair dryer (for softening of plastic)
• 🛠️ Materials:
• Epoxy glue (for example, "Moment Super Epoxy")
• Liquid plastic (Cosmofen Plus or analogues)
• Rubber gaskets (for shock absorption)
• Screws and bushings (if replacement is required)

If you are planning complete replacement of the handle, find its article number in advance. It is indicated on the part itself (usually on the back) or in the instructions for the refrigerator To find a spare part. use:

• Official website LG (section "Spare parts")
• Aggregator sites: eBay, AliExpress, Spare parts for equipment
• Local services (for example, "RemBytTekhnika" or "220-Volt")

Make sure that the refrigerator is unplugged from the network|

Take a photo of the handle fastenings before disassembling|

Prepare the workplace (soft mat for the door)|

Check the presence of all tools|

-->

If you are not sure about the handle model, take a photo of it from different angles and send the photo to the seller - it will help you choose an analogue. Prices for original handles LG start from 1200 rubles, but you can find compatible parts from third-party manufacturers cheaper (from 500 rubles).

Step-by-step instructions: how to remove the handle from the refrigerator door LG

Disassembling the door is the most critical step. If you act carelessly, you can damage the seal or hinges. Follow these instructions:

1. Disconnect. refrigerator unplug and wait until it defrosts (if required).

2. Remove the decorative plugs from the handle (if any). They are usually attached to latches - pry them off with a flat screwdriver.

3. Unscrew the screws under the plugs LG (for example, GA-B429* or GR-N309*) 2-4 screws are used. In some cases, the fastening may be hidden under a plastic cover - it must be carefully removed.

4. Disconnect the handleIf it does not come off, check if there are additional latches inside the door. towards you while simultaneously pressing the clamps.

5. Inspect the mounting holes. If they are damaged, you will have to restore the threads or install new bushings.

On some models (for example, LG Door-in-Door), the handle can be mounted on hidden latches. To open them, you will need a thin screwdriver or a plastic pick. Do not use force - it’s better to watch the video disassembly for your model on YouTube.

What to do if the screws do not come out?

If the screws have soured or are spinning, try the following methods:

1. Apply kerosene or kerosene to the thread, wait 10–15 minutes. WD-40 or kerosene, wait 10–15 minutes.

2. Use a screwdriver with impact mechanism (lightly tap the handle with a hammer).

3. If the screw is broken, drill it out with a thin drill and cut a new thread.

After removing the handle, inspect seal. If it is damaged or deformed, replace it immediately - otherwise, after repair, the door will not close well and the refrigerator will begin to overheat.

How to repair the handle of an LG refrigerator: 3 repair methods

Depending on the type of breakdown, choose one of the restoration methods. We will consider the most reliable methodswhich have been tested in practice.

1. Repairing cracks using epoxy glue

Suitable for handles with cracks up to 5 cm long. Procedure:

1. Clean the surface from grease and dirt (use isopropyl alcohol).
2. Apply glue to the crack with on both sides of the handle. For reliability, you can use fiberglass (sold in radio electronics stores).
3. Squeeze the parts with a clamp or wrap tightly with tape.
4. After. Once dry, sand the seam with sandpaper (400–600 grit).

2. Restoring broken fasteners

If the “ears” of the fasteners break off inside the door, proceed as follows:

1. Drill out the remaining plastic from holes.
2. Insert into the holes metal bushings (you can use furniture ties).
3. Secure the handle with new screws, having previously applied it to the threads thread lock (for example, Loctite).

3. Replacing the handle with a new one

If the handle is critically damaged:

1. Buy a similar part (see the section on spare parts above).
2. Try on the new handle to the door - sometimes adjustments (filing the edges) are required.
3. Install the handle in the reverse order, observing screw tightening torque (do not overtighten!).

After repair, check how the door closes. If it does not fit well, adjust the hinges using a hexagon (instructions are in the manual). refrigerator). springs or does not fit well, adjust the hinges using a hexagon (instructions are in the refrigerator manual).

Common mistakes during repairs and how to avoid them

Even experienced craftsmen sometimes make mistakes that lead to new breakdowns. This is what can't do when repairing the refrigerator handle LG:

• ❌ Use superglue instead of epoxy. It does not withstand loads and peels off quickly.
• ❌ Tighten the screws. "all the way"This leads to thread breakage or deformation of the plastic.
• ❌ Ignore checking the seal. If it is damaged, the refrigerator will waste more energy.
• ❌ Disassemble the door. weight. Place it on a soft surface (for example, a blanket) so as not to scratch it.

Another common mistake is wrong choice of glueFor example, "Moment Crystal" is not suitable for plastic, as it turns yellow and crumbles over time, for example:

• 3M Scotch-Weld DP8005 (two-component adhesive for plastic)
• Permatex Plastic Weld (with reinforcing fibers)
• UHU Plus Endfest 300 (waterproof, withstands up to 100 kg/cm²)

⚠️ Attention: If after the repair, the handle still wobbles, check alignment of the holes in the doors. Sometimes they shift due to metal deformation. In this case, professional straightening may be required.

Where to buy spare parts for the refrigerator LG: proven methods

It is better to buy original handles and fasteners from official dealers, but this is not always profitable. Here is where else you can find quality spare parts:

When purchasing spare parts, pay attention to:

• 🔍 Article details (must match the original).
• 📏 Dimensions (length, width, diameter of mounting holes).
• 🎨 Color (handles are white, silver, black, etc.).

If you buy a handle from AliExpress, check the reviews about the seller. Pay attention to the photos of real buyers - sometimes Chinese parts differ in color or quality of plastic.

FAQ: Answers to frequently asked questions about repairing the handles of LG refrigerators

Is it possible to repair the handle of an LG refrigerator without disassembling the door?

If the crack is small and located on the outside, you can try to seal it liquid plastic (for example Cosmofen) without removing the handle. However, such a repair will be less reliable, since you will not be able to fix the part from the inside. For major repairs, disassembling the door is required.

How much does it cost to replace the handle at a service center? LG?

The cost of work in official services starts from 1500 rubles (excluding spare parts). With a new handle, the total amount will be 3000–6000 rubles, depending on the model of the refrigerator. In unofficial workshops the price tag is lower - from 800 rubles for work.

What to do if after repair the handle still falls off?

Probably a problem in worn fastening bushings inside the door. They need to be replaced with new ones. Also check whether the door itself is deformed - sometimes it is caused by temperature changes, and the handle cannot fit tightly.

Is it possible to use a handle from another refrigerator?

Theoretically, yes, but only if they match:

• Dimensions and shape of the handle;
• Distance between the mounting holes;
• Type of fastening (screws or latches).

Handles from refrigerators LG of the same series or from models Samsung with a similar design are best suited (for example, series RB or RT).

How to temporarily fix the handle if it has fallen off, but there is no new one yet no?

As a temporary solution, you can:

1. Tape the handle to the door with strong electrical tape or construction tape.
2. Use plastic tiesby threading them through the mounting holes.
3. Secure the handle to double-sided tape (not durable, but will help for 1-2 weeks).

Do not forget that such methods are unsafe - the handle can fall off at any moment.