After purchasing new household appliances or transporting them to a new place of residence, the owners the primary task arises - to start the equipment correctly. Samsung No Frost refrigerator It is a complex technical device that requires compliance with certain time intervals before turning it on for the first time, especially if it was transported in a lying position.
Many users make the mistake of hastily connecting the unit to the power supply immediately after unpacking, which can lead to compressor failure. In this article, we will look in detail at how to turn on a Samsung refrigerator how to turn on samsung refrigeratorso that it operates quietly, efficiently and lasts for many years without the need for expensive repairs.
The activation process begins long before you press the power button on the control panel. It is necessary to take into account the physical properties of the refrigerant and oil, which must take their normal places in the system after shaking during transportation. Following the instructions at this stage is a critical factor in the longevity of your device.
Preparation for the first start after purchase
First The next step is a thorough visual inspection of the device after it is delivered to the apartment. Transport packaging must be removed completely, including everything adhesive tapes and protective filmsthat may interfere with the normal operation of mechanisms or air access.
Particular attention should be paid to the inside of the chamber, where shelves and drawers are often fixed using additional fasteners. Transport locks can be made of foam or hard cardboard, and their removal is necessary for the proper functioning of the air circulation system.
After removing the packaging, you must wait until the temperature inside the chambers equalizes to room temperature. This is especially true if the device is brought in from frost, since a sharp temperature change can damage plastic elements and seals.
It is important to check the integrity of the rubber seals on the doors. Deformation of the seal can lead to a loose fit of the door, which will cause constant operation of the compressor and the formation of ice in the future.
Settling time: when to turn it on
One of the most important parameters when starting up for the first time is the settling time. If Samsung refrigerator was transported in an upright position, the minimum waiting time is 2-3 hours. During this time, the oil that has entered the cooling circuit will have time to drain back into the compressor crankcase.
⚠️ Attention: If the device was transported in a horizontal position, the settling time should be at least 8-12 hours. Ignoring this rule can lead to water hammer in the compressor.
In winter, when equipment is brought in from the street, an acclimatization period is added to the settling time. Condensateformed on the internal electronic boards due to temperature changes must completely evaporate before applying voltage.
Why can’t you turn it on right away?
The oil in the compressor spreads throughout the system during transportation. If you turn on the engine immediately, it will try to compress the liquid (oil), which will lead to valve failure or jamming of the piston group. The settling time is necessary for the gravitational return of oil to the reservoir.
You should not rush things, even if it seems that the device has already “warmed up”. Stable operation of the electronics depends on the dryness of the contacts and control boards, which can oxidize in the presence of moisture.
Installation and alignment of the case
Before connecting the power cord to the outlet, you must correctly install the refrigerator case. No Frost system sensitive to distortions, since condensate must flow freely into the drainage tray located above the compressor.
Use a building level or built-in adjustment supports to set the horizontal level. Adjusting the legs This is done by twisting or unscrewing them, which allows you to compensate for uneven floors.
It is recommended to install the refrigerator with a slight tilt back (about 2 degrees). This will ensure automatic closing of the doors under the influence of gravity and a tight fit magnetic seal.
Ensure sufficient clearance between the back wall of the device and the wall of the room. Ventilation holes should not be closed, as this will lead to overheating of the condenser and increased energy consumption.
Connecting to the power supply
For connection Samsung refrigerator use only an individual socket with grounding. The use of extension cords, tees or low-quality surge protectors is not recommended, as the starting currents of the compressor can be high.
☑️ Check before turning on
Insert the plug into the socket until it stops. In some models, when turned on for the first time, a characteristic click of the relay may be heard - this is a normal phenomenon, indicating the start of operation of the control system control systems.
If the indicators on the control panel light up, it means that power is supplied correctly. Lack of response may indicate a lack of voltage in the network or a malfunction of the power cable itself.
Make sure that the outlet does not heat up during operation. Contact heating indicates a poor connection or insufficient wiring cross-section, which can cause a fire.
Primary setting of temperature and modes
After power is applied, the refrigerator switches to the default operating mode. Usually this is standard cooling modein which the temperature in the refrigerator compartment is set at +3°C, and in the freezer -18°C or -20°C.
To change the parameters, use the control panel located on the outside of the door or inside the chamber. By pressing the button Freezer or Fridge, you can adjust the degree of cooling in the corresponding compartments.
| Mode | Temperature (HC) | Temperature (MK) | Description |
|---|---|---|---|
| Standard | +3°C | -18°C | Optimal for daily use |
| Eco | +4°C | -18°C | Energy saving |
| Power Cool | +1°C | No changes | Quick cooling of products |
| Power Freeze | No change | -23°C | Quick freezing |
Mode Power Cool is useful when you need to quickly cool a large amount of food brought from the store. However, it is not recommended to keep it on all the time to avoid excessive load on the compressor.
Models with a digital display may display an error code or flashing light if the door is left open too long when first started. Just close the door, and the indication should return to normal in a few minutes.
Loading with products and entering the mode
Full stabilization of the temperature in the chambers No Frost takes from 2 to 4 hours. At this time, it is not recommended to open the doors unless absolutely necessary, so as not to disrupt the cooling process.
The first loading of products should be done gradually. Overflow of the chambers in the first hours of operation may cause the compressor to work without stopping, trying to cool a large volume of warm mass.
⚠️ Attention: Do not place food close to the back wall of the refrigerator compartment. Cold air circulation channels are located there, and blocking them will lead to local hypothermia or spoilage of products.
Distribute products evenly, leaving space between them for free circulation of air flows. System No Frost works effectively only when air can move freely throughout the entire volume of the chambers.
Frequently asked questions when starting up (FAQ)
Why does the Samsung refrigerator hum loudly immediately after turning on?
In the first hours of operation, the compressor may work with increased load in order to cool the warm internal volume. The hum may also be caused by the circulation of refrigerant in the pipes. If the noise does not subside after a day or is accompanied by vibration of the case, check the adjustment of the support legs.
What does the flashing "Ice Max" or "C" indicator mean?
Flashing indicators often indicate that the door has been open for a long time or the temperature inside the chambers is higher than normal. After closing the door and entering the mode, the indication should go out. If the blinking continues for more than 24 hours, diagnostics of the sensors may be required.
Is it possible to connect the refrigerator to the network via an extension cord?
Manufacturers do not recommend using extension cords, especially cheap ones, as they may not withstand the starting current of the compressor. If the use of an extension cord is unavoidable, make sure that it has a wire cross-section of at least 1.5 mm² and is designed for a current of at least 10-16 Amps.
Is it necessary to defrost a new No Frost refrigerator before turning it on?
No, the system No Frost (without frost) assumes automatic moisture removal and no need for manual defrosting. Factory lubrication and cleanliness of the internal chambers do not require additional procedures before the first start, except for removing the packaging.